<Desc/Clms Page number 1>
EMI1.1
EMI1.2
<Desc/Clms Page number 2>
EMI2.1
platte al am Geschützrohrbodenstücke anliegt.
Beim Öffnen des Verschlusses erfasst man den Griff J und dreht ihn nach dem Geschützrohre hin. Der Drehung des Griffes J folgt unter Vermittlung der Anschläge / die Klinke F,
EMI2.2
Wenn unmittelbar nach Beginn der Drehung der Handkurbel E die Grenzplatte al des Ver- se. hlusskeiles in die aus Fig. 5 ersichtliche Lage zum Geschützrohrbodenstücke C gelangt ist, hat der Riegel G seine Anlage am Geschützrohrbodenstücke verloren. Er hat sich dann unter der Wirkung seiner Feder g2 in seinem Lager um ein solches Mass verschoben, dass seine Nase g1 aus der Bahn der Nase f1 der in der Sperrstellung befindlichen Klinke F getreten ist.
Infolgedessen braucht man beim Drehen der Handkurbel E - zum Öffnen des Verschlusses ist, wie erwähnt, mehr als eine volle Umdrehung der Transportschraube B erforderlich-weder die Klinke F in der ausgerückten Stellung zu halten noch sie von neuem auszurücken, wenn nach einer vollen Umdrehung der Handkurbel, deren die Klinke F tragender Arm in die aus Fig. 5 ersichtliche Stellung zum Riegel G gelangt ist.
Das Schliessen des Verschlusses wird durch eine Drehung der Handkurbel E in der dem Sinne des Pfeiles x entgegengesetzten Richtung bewirkt. Im letzten Teile der Schliessbewegung des Verschlusskeiles wird der Riegel G dadurch, dass er zur Anlage an das Geschützrohrbodenstück C kommt, durch dieses in seine Sperrstellung zurückgeführt. Wenn der Riegel G diese Stellung nahezu erreicht hat. trifft die Nase f1 der in der Sperrstellung befindlichen Klinke F mit ihrer Schrägfläche f5 gegen die Schrägfläche g5 der Nase 91 des Riegels G. Infolgedessen weicht, während der Handkurbel J ? der letzte Teil ihrer Drehung erteilt wird, die Klinke F dem Riegel G aus.
In dem Augenblicke aber, in dem die Grenzplatte al des Verschlusskeiles zur Anlage an das Geschütz- roh rbodenatück gelangt ist und der Riegel G seine Sperrstellung erreicht hat, gibt die Nase gl
EMI2.3
Gesperrt F C ist dann wieder eingerückt und der Verschluss ist gegen unbeabsichtigtes Öffnen gesichert.
PATENT-ANSPRÜCHE :
1. Gesperre zum Festlegen der Handkurbel von Geschützkeilverschlüssen mit Transportschraube, dadurch gekennzeichnet, dass derjenige Teil (G) des Gesperres (F G), der zum Eingriffe mit dem an der Verschlusskurbel (E) angeordneten Gesperrteile (F) bestimmt ist, am Verschlusskeile (A) derartig beweglich angeordnet ist, dass er im ersten Teile der öffnung- bewegung des Verschlusskeiles seine Sperrstellung selbsttätig verlässt und gegen Ende der Schliessbewegung des Verschlusskeiles selbsttätig in seine Sperrstellung zurückgeführt wird.
<Desc / Clms Page number 1>
EMI1.1
EMI1.2
<Desc / Clms Page number 2>
EMI2.1
plate al rests on the barrel base.
When opening the breech, one grasps the handle J and turns it towards the gun barrel. The rotation of the handle J follows through the intermediary of the stops / the pawl F,
EMI2.2
If immediately after the start of the rotation of the hand crank E, the boundary plate a1 of the locking wedge has reached the position of the gun barrel base piece C shown in FIG. 5, the bolt G has lost its contact with the gun barrel base piece. Under the action of his spring g2 he has then shifted in his bearing by such an amount that his nose g1 has stepped out of the path of the nose f1 of the pawl F in the blocking position.
As a result, when turning the hand crank E - as mentioned, more than one full turn of the transport screw B is required to open the shutter - neither the pawl F must be held in the disengaged position nor it must be disengaged again if, after one full turn the Hand crank whose arm carrying the pawl F has reached the position of the latch G shown in FIG.
The closure of the lock is effected by turning the hand crank E in the direction opposite to that of the arrow x. In the last part of the closing movement of the locking wedge, the bolt G is returned to its blocking position by the fact that it comes to rest against the gun barrel bottom section C. When the bolt G has almost reached this position. the nose f1 of the pawl F in the locked position hits with its inclined surface f5 against the inclined surface g5 of the nose 91 of the bolt G. As a result, while the hand crank J? the last part of its rotation is granted, the pawl F to the bolt G out.
At the moment, however, in which the boundary plate a1 of the locking wedge has come to rest on the gun barrel and the bolt G has reached its locking position, the nose gl
EMI2.3
Locked F C is then re-engaged and the lock is secured against unintentional opening.
PATENT CLAIMS:
1. Lock for fixing the hand crank of gun wedge locks with transport screw, characterized in that that part (G) of the lock (FG) which is intended to intervene with the locking parts (F) arranged on the lock crank (E) is attached to the lock wedge (A ) is arranged movably in such a way that it leaves its locking position automatically in the first part of the opening movement of the locking wedge and is automatically returned to its locking position towards the end of the locking movement of the locking wedge.