Application Guide
Chiller Plant Design
51.5F Return Water
To Chiller
Two 400 Ton Chillers
Each At 300 Tons
(Balanced Load)
Chiller 1- On
Two Primary Pumps
Each At 960 gpm
Building Load
600 Tons
(50% Load)
54F
51.5F
480 gpm Flow Through
Decoupler
44F
Flow
Chiller 2- On
44F
Chiller 3- Off
Secondary Pump
1440 gpm
Elevation Difference
Column Height
When Pump Is Off
© 2002 McQuay International
AG 31-003-1
Table of Contents
Introduction ................................................................................................................. 4
Using This Guide............................................................................................................................... 4
Basic System ............................................................................................................... 4
Chiller Basics..................................................................................................................................... 4
Piping Basics ..................................................................................................................................... 7
Pumping Basics ............................................................................................................................... 11
Cooling Tower Basics...................................................................................................................... 15
Load Basics ..................................................................................................................................... 20
Control Valve Basics ....................................................................................................................... 20
Loop Control Basics ........................................................................................................................ 23
Piping Diversity............................................................................................................................... 24
Water Temperatures and Ranges ............................................................................... 25
Supply Air Temperature................................................................................................................... 25
Chilled Water Temperature Range................................................................................................... 26
Condenser Water Temperature Range.............................................................................................. 26
Temperature Range Trends .............................................................................................................. 27
Air and Evaporatively Cooled Chillers ..................................................................... 28
Air-Cooled Chillers ......................................................................................................................... 28
Evaporatively Cooled Chillers......................................................................................................... 30
Dual Compressor and VFD Chillers ......................................................................... 31
Dual Compressor Chillers................................................................................................................ 31
VFD Chillers ................................................................................................................................... 31
System Design Changes................................................................................................................... 32
Mechanical Room Safety .......................................................................................... 34
Standard 34...................................................................................................................................... 34
Standard 15...................................................................................................................................... 34
Single Chiller System................................................................................................ 38
Basic Operation ............................................................................................................................... 38
Basic Components ........................................................................................................................... 38
Single Chiller Sequence of Operation.............................................................................................. 39
Parallel Chiller System.............................................................................................. 41
Basic Operation ............................................................................................................................... 41
Basic Components ........................................................................................................................... 41
Parallel Chiller Sequence of Operation ........................................................................................... 42
Series Chillers ........................................................................................................... 44
Basic Operation ............................................................................................................................... 44
Basic Components ........................................................................................................................... 44
Series Chillers Sequence of Operation ............................................................................................ 46
Series Counterflow Chillers............................................................................................................. 47
Using VFD Chillers in Series Arrangements ................................................................................... 49
System Comparison ......................................................................................................................... 49
Primary/Secondary Systems ...................................................................................... 51
2
Application Guide AG 31-003-1
Basic Operation ............................................................................................................................... 51
Basic Components ........................................................................................................................... 51
Very Large Chiller Plants................................................................................................................. 58
Primary/Secondary Sequence of Operation ..................................................................................... 58
Water-Side Free Cooling ........................................................................................... 61
Direct Waterside Free Cooling......................................................................................................... 61
Parallel Waterside Free Cooling ...................................................................................................... 61
Series Waterside Free Cooling......................................................................................................... 62
Waterside Free Cooling Design Approach ....................................................................................... 63
Cooling Tower Sizing ...................................................................................................................... 63
Waterside Free Cooling Sequence of Operation .............................................................................. 64
Economizers and Energy Efficiency ................................................................................................ 65
Hybrid Plants............................................................................................................. 66
Heat Recovery and Templifiers™ ............................................................................. 67
General............................................................................................................................................. 67
Load Profiles.................................................................................................................................... 67
Heat Recovery Chillers .................................................................................................................... 67
Templifiers™ ................................................................................................................................... 71
ASHRAE Standard 90.1 .................................................................................................................. 73
Variable Primary Flow Design .................................................................................. 75
Basic Operation ............................................................................................................................... 75
Basic Components ........................................................................................................................... 75
Variable Primary Flow Sequence of Operation................................................................................ 76
Training and Commissioning ........................................................................................................... 78
Low Delta T Syndrome ............................................................................................. 80
Low Delta T Example ...................................................................................................................... 80
Low Delta T Syndrome Causes and Solutions ................................................................................. 82
Other Solutions ................................................................................................................................ 84
Process Applications ................................................................................................. 86
Process Load Profiles ...................................................................................................................... 86
Condenser Relief.............................................................................................................................. 87
Winter Design .................................................................................................................................. 87
Chilled Water Volume ...................................................................................................................... 87
Temperatures and Ranges ................................................................................................................ 88
Minimum Chilled Water Volume .............................................................................. 89
Estimating System Volume .............................................................................................................. 89
Evaluating System Volume .............................................................................................................. 89
Conclusions ............................................................................................................... 92
References ................................................................................................................. 93
The information contained within this document represents the opinions and suggestions of
McQuay International. Equipment, the application of the equipment, and the system
suggestions are offered by McQuay International as suggestions only, and McQuay
International does not assume responsibility for the performance of any system as a result of
these suggestions. Final responsibility for the system design and performance lies with the
system engineer.
Application Guide AG 31-003-1
3
Introduction
Using chilled water to cool a building or process is efficient and flexible. A two-inch Schedule 40
pipe of chilled water can supply as much comfort cooling as 42" diameter round air duct. The use of
chillers allows the design engineer to produce chilled water in a central building location or even on
the roof and distribute the water economically and without the use of large duct shafts. Chilled water
also provides accurate temperature control that is especially useful for variable air volume (VAV)
applications.
The purpose of this manual is to discuss various piping and control strategies commonly used with
chilled water systems including variable flow pumping systems.
Using This Guide
This Guide initially discusses the components used in a chilled water
system. It then reviews various chiller plant designs explaining their
operation, strengths and weaknesses. Where appropriate, sequence of
operations are provided. Each project is unique so these sequences are
just guidelines.
In addition, many sections reference ASHRAE Standard 90.1-2001. The
ASHRAE section numbers are provided in parentheses to direct the
reader. The sections referenced in this Guide are by no means complete.
It is recommended that the reader have access to a copy of Standard 90.1
as well as the Users Manual. The Standard and manual can be purchased
online at WWW.ASHRAE.org.
Basic System
Figure 1 shows a basic chiller loop with a water-cooled chiller. The system consists of a chiller,
cooling tower, building cooling load, chilled water and condensing water pumps and piping. This
section will review each of the components.
Figure 1 - Single Chiller Loop
Chiller Basics
The chiller can be water-cooled, air-cooled or evaporatively cooled. The compressor types typically
are reciprocating, scroll, screw or centrifugal. The evaporator can be remote from the condensing
section on air-cooled units. This
has the advantage of allowing the
Building Load
chilled water loop to remain inside
the building envelope when using
Condenser
an outdoor chiller. In applications
Water Loop
where freezing conditions can be
expected, keeping the chilled water
Cooling Tower
loop inside the building avoids the
Chilled Water Pump
need for some form of antifreeze.
Chiller
Condenser
Water Pump
4
Chilled Water Loop
There can be multiple chillers in a
chilled water plant. The details of
various multiple chiller plant
designs will be discussed in future
sections.
Application Guide AG 31-003-1
The chilled water flows through the evaporator of the chiller. The evaporator is a heat exchanger
where the chilled water gives up its sensible heat (the water temperature drops) and transfers the heat
to the refrigerant as latent energy (the refrigerant evaporates or boils).
Flow and Capacity Calculations
For air conditioning applications, the common design conditions are 44°F supply water temperature
and 2.4 gpm/ton. The temperature change in the fluid for either the condenser or the evaporator can
be described using the following formula:
Q = W x C x ∆T
Where
Q = Quantity of heat exchanged (Btu/hr)
W = flow rate of fluid (USgpm)
C = specific heat of fluid (Btu/lb· °F)
∆T = temperature change of fluid (°F )
Assuming the fluid is water, the formula takes the more common form of:
Load (Btu/hr) = Flow (USgpm) x (°Fin – °Fout) x 500
Or
Load (tons) = Flow (USgpm) x (°Fin – °Fout)/24
Using this equation and the above design conditions, the temperature change in the evaporator is
found to be 10°F. The water temperature entering the evaporator is then 54°F.
Most air conditioning design conditions are based on 75°F and 50% relative humidity (RH) in the
occupied space. The dewpoint for air at this condition is 55.08°F. Most HVAC designs are based on
cooling the air to this dewpoint to maintain the proper RH in the space. Using a 10°F approach at the
cooling coil means the supply chilled water needs to be around 44°F or 45°F.
The designer is not tied to these typical design conditions. In fact, more energy efficient solutions can
be found by modifying the design conditions, as the project requires.
Changing the chilled water flow rate affects a specific chiller's performance. Too low a flow rate
lowers the chiller efficiency and ultimately leads to laminar flow. The minimum flow rate is typically
around 3 fps (feet per second). Too high a flow rate leads to vibration, noise and tube erosion. The
maximum flow rate is typically around 12 fps. The chilled water flow rate should be maintained
between these limits of 3 to 12 fps.
The condenser water flows through the condenser of the chiller. The condenser is also a heat
exchanger. In this case the heat absorbed from the building, plus the work of compression, leaves the
refrigerant (condensing the refrigerant) and enters the condenser water (raising its temperature). The
condenser has the same limitations to flow change as the evaporator.
Chillers and Energy Efficiency
Chillers are often the single largest electricity users in a building. A 1000 ton chiller has a motor
rated at 700 hp. Improving the chiller performance has immediate benefit to the building operating
cost. Chiller full load efficiency ratings are usually given in the form of kW/ton, COP (Coefficient of
Performance = kWcooling / kWinput) or EER (Energy Efficiency Ratio = Tons X 12/ kWinput). Full load
performance is either the default ARI conditions or the designer specified conditions. It is important
to be specific about operating conditions since chiller performance varies significantly at different
operating conditions.
Application Guide AG 31-003-1
5
Chiller part load performance can be given at designer-specified conditions or the NPLV (NonStandard Part Load Value) can be used. The definition of NPLV is spelled out in ARI 550/590-98,
Test Standard for Chillers. For further information refer to McQuay Application Guide AG 31-002,
Centrifugal Chiller Fundamentals.
☺Tip: To convert from COP to kW/ton;
COP = 3.516/(kW/ton)
To calculate EER = Tons x 12/(total kW input)
1
Figure 2 - ASHRAE Std 90.1 Chiller Performance Table
Water Chilling Packages – Minimum Efficiency Requirements
Equipment Type
Air Cooled, with Condenser,
Electrically Operated
Air Cooled, without Condenser,
Electrically Operated
Water Cooled, Electrically Operated,
Positive Displacement (Reciprocating)
Water Cooled,
Electrically Operated,
Positive Displacement
(Rotary Screw and Scroll)
Size Category
<150 tons
>150 tons
All Capacities
All Capacities
<150 tons
>150 tons and
<300 tons
>300 tons
Water Cooled, Electrically Operated,
Centrifugal
<150 tons
>l50 tons and
<300 tons
>300 tons
Air-Cooled Absorption Single Effect
Water-Cooled Absorption Single
Effect
Absorption Double Effect, IndirectFired
Absorption Double Effect, Direct-Fired
All Capacities
All Capacities
All Capacities
All Capacities
Subcategory or
Rating
Condition
Minimum Efficient
Test Procedure
2.80 COP
3.05 IPLV
ARI 550/590
3.10 COP
3.45 IPLV
4.20 COP
5.05 IPLV
4.45 COP
5.20 IPLV
4.90 COP
5.60 IPLV
5.50 COP
6.15 IPLV
5.00 COP
5.25 IPLV
5.55 COP
5.90 IPLV
6.10 COP
6.40 IPLV
0.60 COP
0.70 COP
ARI 550/590
ARI 550/590
ARI 5 50/590
ARI 560
1.00 COP
1.05 IPLV
1.00 COP
1.00 IPLV
a The chiller equipment requirements do not apply for chillers used in low-temperature applications where the design leaving fluid temperature is <4°F.
b Section 12 contains a complete specification of the referenced test procedure, including the referenced year version of the test procedure.
Since buildings rarely operate at design load conditions (typically less than 2% of the time) chiller
part load performance is critical to good overall chiller plant performance. Chiller full and part load
efficiencies have improved significantly over the last 10 years (Chillers with NPLVs of 0.35 kW/ton
are available) to the point where future chiller plant energy performance will have to come from
chiller plant design.
ASHRAE Standard 90.1-2001 includes mandatory requirements for minimum chiller performance.
Table 6.2.1.C of this standard covers chillers at ARI standard conditions. Tables 6.2.1H to M cover
centrifugal chillers at non-standard conditions.
1
Copyright 2001, American Society Of Heating, Air-conditioning and Refrigeration Engineers Inc.,
www.ashrae.org. Reprinted by permission from ASHRAE Standard 90.1-2001
6
Application Guide AG 31-003-1
Piping Basics
Static Pressure
Figure 3 - Closed Loop
Static Head
Water Column
Water Column
The piping is usually steel, copper or
plastic. The chilled water piping is
usually a closed loop. A closed loop is
not open to the atmosphere. Figure 3
shows a simple closed loop with the
pump at the bottom of the loop. Notice
that the static pressure created by the
change in elevation is equal on both sides
of the pump. In a closed loop, the pump
needs only to overcome the friction loss
in the piping and components. The pump
does not need to “lift” the water to the
top of the loop.
When open cooling towers are used in
condenser piping, the loop is an open
type. Condenser pump must overcome
the friction of the system and “lift” the water from the sump to the top of the cooling tower. Figure 4
shows an open loop. Notice the pump need only overcome the elevation difference of the cooling
tower, not the entire building.
In high-rise applications, the static pressure can
☺Tip: Most chillers are rated for 150 PSI
become considerable and exceed the pressure
water side pressure. This should be considered
rating of the piping and the components such as
carefully for buildings over 10 stories.
chillers. Although chillers can be built to
higher pressure ratings (The standard is typically 150 PSI but the reader is advised to check with the
manufacturer) high pressure systems can become expensive. The next standard rating is typically 300
PSI. Above that, the chillers become very expensive. One solution is to use heat exchangers to
isolate the chillers from the static pressure. While this solves the pressure rating for the chiller, it
introduces another device and another approach that affects supply water temperature and chiller
performance. A second solution is to locate chiller plants on various floors throughout the building
selected to avoid exceeding the 150 PSI chiller rating.
Figure 4 -Open Loop
Elevation Difference
Column Height
When Pump Is Off
Application Guide AG 31-003-1
Expansion Tanks
An expansion tank is required in the chilled
water loop to allow for the thermal
expansion of the water. Expansion tanks
can be open type, closed type with air-water
interface or diaphragm type. Tank location
will influence the type. Open tanks must
be located above the highest point in the
system (for example, the penthouse). Airwater interface and diaphragm type tanks
can be located anywhere in the system.
Generally, the lower the pressure in the
tank, the smaller the tank needs to be. Tank
size can be minimized by locating it higher
in the system.
7
Figure 5 - Expansion Tank Location
Discharge Pressure =
Expansion Tank Pressure +
Pump Head
Suction Pressure =
Expansion Tank Pressure
-Pump Head
Discharge Pressure =
Expansion Tank Pressure
The pressure at which the tank is operated is the reference point for the entire hydronic system. The
location of the tank -which side on the pump (suction or discharge) - will affect the total pressure seen
by the system. When the pump is off, the tank will be exposed to the static pressure plus the pressure
due to thermal expansion. If the tank is located on the suction side, when the pump is running, the
total pressure seen on the discharge side will be the pressure differential, created by the pump, added
to the expansion tank pressure. If the expansion tank is located on the discharge side of the pump, the
discharge pressure will be the same as the expansion tank pressure and the suction side pressure will
be the expansion tank pressure minus the pump pressure differential.
Piping Insulation
Chilled water piping is insulated since the water and hence the piping is often below the dewpoint
temperature. Condensate would form on it and heat loss would occur. The goal of the insulation is to
minimize heat loss and maintain the outer surface above the ambient air dewpoint.
Condenser Water Piping
In most cases, the condenser water piping is an open loop. Figure 4 shows an open loop with the
water open to the atmosphere. When the pump is not running, the level in the supply and return
piping will be even at the level of the sump. When the pump operates, it needs to overcome the
friction loss in the system and “lift” the water from the sump level to the top of the loop. Condenser
water piping is typically not insulated since there will be negligible heat gain or loss and sweating will
not occur. If the piping is exposed to cold ambient conditions, however, it could need to be insulated
and heat traced to avoid freezing.
8
Application Guide AG 31-003-1
Reverse Return/Direct Return Piping
Figure 6 - Reverse Return Piping
Figure 6 shows reverse return piping. Reverse return piping is designed such that the path through
any load is the same length and therefore has approximately the same fluid pressure drop. Reverse
return piping is inherently self-balancing. It also requires more piping and consequently is more
expensive.
Figure 7 - Direct Return Piping
Direct return piping results in the load closest to the chiller plant having the shortest path and
therefore the lowest fluid pressure drop. Depending on the piping design, the difference in pressure
drops between a load near the chiller plant and a load at the end of the piping run can be substantial.
Balancing valves will be required. The advantage of direct return piping is the cost savings of less
piping.
For proper control valve selection, it is necessary to know the pressure differential between the supply
and return header (refer to Control Valve Basics, page 20). While at first it would appear with
reverse return piping, that the pressure drop would be the same for all devices, this is not certain.
Changes in pipe sizing in the main headers, different lengths and fittings all lead to different pressure
differentials for each device. When the device pressure drop is large relative to piping pressure
losses, the difference is minimized.
In direct return piping, the pressure drops for each device vary at design conditions depending on
where they are in the system. The valve closest to the pumps will see nearly the entire pump head.
Valves at the furthest end of the loop will see the minimum required pressure differential. Assuming
Application Guide AG 31-003-1
9
the pressure differential sensor is located at the furthest end, all valves in a direct return system should
be selected for the minimum pressure differential. This is because if any one device is the only one
operating, the pressure differential controller will maintain the minimum differential across that
device.
The decision whether to use direct or reverse return piping should be based on system operability vs.
first cost. Where direct return piping is used, flow-balancing valves should be carefully located so
that the system can be balanced.
Piping and Energy Efficiency
Piping materials and design have a large influence on the system pressure drop, which in turn affects
the pump work. Many of the decisions made in the piping system design will affect the operating cost
of the chiller plant every hour the plant operates for the life of the building. When viewed from this
life cycle point of view, any improvements that can lower the operating pressure drop should be
considered. Some areas to consider are:
Y
Pipe material. Different materials have different friction factors.
Y
Pipe sizing. Smaller piping raises the pressure drop. This must be balanced against the capital
cost and considered over the lifetime of the system.
Y
Fittings. Minimize fittings as much as possible.
Y
Valves. Valves represent large pressure drops and can be costly. Isolation and balancing valves
should be strategically placed.
Y
Direct return vs. Reverse return.
Piping insulation reduces heat gain into the chilled water. This has a compound effect. First, any
cooling effect that is lost due to heat gain is additional load on the chiller plant. Second, in most
cases, to account for the resultant temperature rise, the chilled water setpoint must be lowered to
provide the correct supply water temperature at the load. This increases the lift on the chillers and
lowers their performance.
ASHRAE 90.1-2001 requires the following for piping systems:
Y
Piping must be insulated as per ASHRAE Standard 90.1 Table 6.2.4.1.3. (See Table 1)
Exceptions include:
Y
Y
Factory installed insulation.
Y
Systems operating between 60°F and 105°F.
The hydronic system be proportionally balanced in a manner to first minimize throttling losses
and then the impeller trimmed or the speed adjusted to meet the design flow conditions
(6.2.5.3.3)
Exceptions include:
Pumps with motors less than 10 hp.
Y
When throttling results in no greater than 5% of nameplate horsepower or 3 hp, whichever is
less.
Y
Three pipe systems with a common return for heating and cooling are not allowed. (6.3.2.2.1)
Y
Two pipe changeover systems are acceptable providing: (6.3.2.2.2)
Y
10
Y
Y
Controls limit changeovers based on15°F ambient drybulb deadband.
Y
System will operate in one mode for at least 4 hours.
Y
Reset controls lower the changeover point to 30°F or less.
Systems with total pump nameplate horsepower exceeding 10 hp shall be variable flow able to
modulate down to 50%. (6.3.4)
Application Guide AG 31-003-1
2
Table 1 - Minimum Piping Insulation As Per Std 90.1
Fluid
Design
Operating
Temp.
Range (°F)
Insulation Conductivity
Conductivity
Btu•in/(h•ft2•°F)
40-60
>60
0.22-0.28
0.22-0.28
Mean Rating
Temp °F
Nominal Pipe or Tube Size (in)
<1
1 to <1-1/2
1-1/2 to <4
Cooling Systems (Chilled Water, Brine and Refrigerant)
100
0.5
0.5
1.0
100
0.5
1.0
1.0
4<8
>8
1.0
1.0
1.0
1.5
Pumping Basics
Figure 8 - Inline Centrifugal Pump
Typically centrifugal type pumps are used for both condenser
water and chilled water systems. They can be either inline or base
mounted. The pumps must be sized to maintain the system
dynamic head and the required flow rate. Normally, the pumps are
located so they discharge into the chiller heat exchangers.
Figure 9 - Basic Pump Curve
50
Pump Curve
Total He ad, ft
40
Point of Operation
30
20
10
System Curve
0
0
50
100
150
200
250
Centrifugal pumps are non-positive displacement type
so the flow rate changes with the head. The actual
operating point is where the system curve crosses the
pump curve. In systems with control valves, the
system curve changes every time a valve setting
changes. This is important because the pump affinity
laws cannot be used to estimate a change if the system
curve is allowed to change. Identical pumps in
parallel will double the flow at the same head.
Identical pumps in series will double the head.
Capacity , gpm
2
Copyright 2001, American Society Of Heating, Air-conditioning and Refrigeration Engineers Inc.,
www.ashrae.org. Reprinted by permission from ASHRAE Standard 90.1-2001
Application Guide AG 31-003-1
11
Figure 10 - Pump Curve Profiles
Total He ad
Steep
Flat
Figure 10 shows a steep and flat curve profile.
Different pumps provide different profiles each with
their own advantages. The steep curve is better suited
for open systems such as cooling towers where high lift
and stable flow are desirable. The flat profile is better
suited for systems with control valves. The flat profile
will maintain the necessary head over a wide flow
range.
Capacity
Figure 11 – Typical Centrifugal Pump Curve
Total Head (ft)
Efficiency
Required
NPSH
Impeller Dia.
Flow (Usgpm)
BHP
Figure 11 shows a typical pump curve.
Since pumps are direct drive, the pump
☺Tip: For a constant system curve, the following
curves are typically for standard motor
pump affinity laws may be used;
speeds (1200, 1800 or 3600 rpm). The
required flowrate and head can be plotted
At constant impeller diameter (Variable speed)
and the subsequent efficiency and
RPM1 / RPM2 = gpm1 / gpm2 = (H1 )½/(H2 )½
impeller diameter can be found. As the
flow increases, generally the Net Positive
At constant speed (Variable impeller diameter)
Suction Head (NPSH) decreases. This is
D1 / D2 = gpm1 / gpm2 = (H1 )½/(H2 )½
due to the increased fluid velocity at the
inlet of the impeller. NPSH is required by the pump to avoid the fluid flashing to gas in the inlet of
the impeller. This can lead to cavitation and pump damage. NPSH is an important consideration with
condenser pumps particularly when the chillers are in the penthouse and the cooling towers are on the
same level.
12
Application Guide AG 31-003-1
Multiple Pumps
To provide redundancy, multiple pumps are used. Common approaches are (1) a complete full-sized
stand-by pump, or (2) the design flow is met by two pumps with a third stand-by pump sized at half
the load. When multiple pumps are used in parallel, check valves on the discharge of each pump are
required to avoid “short circuiting”. Pumps can also utilize common headers to allow one pump to
serve multiple duties (headered primary pumps serving multiple chillers). Refer to Primary Pumps,
page 52 for more information on primary pumps.
Variable Flow Pumps
Many applications require the flow to change in response to load. Modulating the flow can be
accomplished by:
Y
Riding the pump curve
Y
Staging on pumps
Y
Using variable frequency drives (VFDs)
Riding the pump curve is typically used on small systems with limited flow range. Staging on pumps
was the traditional method until VFDs. Today, VFDs are the most common method for varying flow.
They are the most efficient method as well. System flow is usually controlled by maintaining a
pressure differential between the supply and return lines. The measuring point should be at or near
the end of the pipe runs as opposed to being in the mechanical room to reduce unnecessary pump
work. This is particularly true for direct return systems.
Figure 12 shows the differential
☺Tip: The differential pressure setpoint for variable
pressure sensor located at the end of
flow pumps should based on field measurements taken
the piping run. At design load, the
during commissioning and balancing. Using an
pressure drop across coil 1 is 60 ft
estimated setting may lead to unnecessary pump work
while the pressure drop across coil 5 is
for the life of the building
only 30 ft. Then differential pressure
controls should be set up to maintain 30 ft. When only coil 1 is operating, the pressure differential
across coil 1 will only be 30 ft if the differential sensor is located at the end of the run as shown. If the
sensors had been near the pumps, however, the differential controller would have to have been set for
60 ft to meet the design requirements. When only coil 1 operates, the pressure would have been
maintained at 60 ft, which would have wasted pump work.
Figure 12 - Secondary Pump Control in Direct Return Systems
Design PD Is
30 Ft
Design PD is 60 Ft
When Only Coil 1
Operates
Required PD Is 30 Ft
Differential
Pressure
Sensor
Coil 1
Coil 5
Another method of controlling variable flow pumps is to monitor the valve positions of a control
valve in a critical part of the system. This valve is typically the furthest from the pumps. The control
Application Guide AG 31-003-1
13
system then maintains the minimum pressure differential necessary, which allows the valve to
maintain setpoint. The advantage of this approach is the system pressure is maintained at the
minimum required to operate properly and that translates into minimum pump work.
When multiple pumps are required to be variable flow, such as the secondary pumps of a primarysecondary system, VFDs are recommended on all pumps. Consider a system with two equal pumps,
both are required to meet the design flow. Pump 1 has a VFD while pump 2 does not. From 0 to 50%
flow, pump 1 can be used with its VFD. Above 50%, the second pump will be required. When pump
2 is started, it will operate at design speed. It will overpower pump 1, which will need to operate at
less than design speed and will not generate the same head.
Figure 13 - Pumping Power vs. Flow
3
Figure 13 shows percent pumping power as a
function of percent flow. From this figure, it can
be seen that VFD pumps will not save much
energy below 33% or 20Hz. Operating pumps
much below 30% starts to create problems for
motors, chiller minimum flows, etc. Since there are
minimal savings anyway, the recommended
minimum frequency is 20 Hz.
Pin/Pshaft, Nominal
1.2
1
0.8
Little Energy
Savings Below
20 Hz
0.6
0.4
0.2
0
0
20
40
60
80
100
% Of Flow (Or % Of Speed)
Pump Law, Pin/Pshaft, Nominal (Spead)^3
Properly Sized Motor
Pumps and Energy Efficiency
Pump work is deceptive. Although the motors tend to be small (when compared to chiller motors),
they operate whenever the chiller operates. In a single water-cooled chiller plant with constant chilled
water flow, it is not unusual for the pumps to use two-thirds of the energy consumed by the chiller.
Optimal use of pumps can often save more energy than any other improvement to a chiller plant.
Figure 14 - Motor and VFD Efficiency At Part Load
100
100
ηm
90
ηVFD
60
80
40
70
ηm=94.187(1-e-0.0904x)
20
60
ηVFD=50.87+1.283x-0.0142x2+5.834x10-5x3
0
50
0
10
20
30
40
50
60
70
80
% Of Name - Plate Load (Motor)
Or % Nominal Speed (VFD)
90
100
VFD Efficiency, %
Motor Efficiency, %
80
When both motors and VFDs operate at
less than 100% capacity, their
efficiency drops off. Figure 14 shows
motor and VFD efficiencies at part
load. It can be seen that oversizing
motors can lead to significantly poorer
performance than expected.
Oversizing pumps themselves also
leads to wasted energy. If the pumps
produce too much flow, the flow will be
throttled, usually with a balancing
valve, to meet the desired flow. This
creates an unnecessary pressure drop
and consumes power all the time the
pump operates. The solution in most
cases, is to trim the impeller.
3
Bernier, Michel., Bernard Bourret, 1999. Pumping Energy and Variable Speed Drives. ASHRAE
Journal, December 1999. ASHRAE. Atlanta, Ga.
14
Application Guide AG 31-003-1
ASHRAE 90.1-2001 requires the following for pumps:
Y
The hydronic system be proportionally balanced in a manner to first minimize throttling losses
and then the impeller trimmed or the speed adjusted to meet the design flow conditions
(6.2.5.3.3)
Exceptions include:
Y
Pumps with motors less than 10 hp.
Y
When throttling results in no greater than 5% of nameplate horsepower or 3 hp, whichever is
less.
Y
Systems with total pump nameplate horsepower exceeding 10 hp shall be variable flow able to
modulate down to 50%. (6.3.4)
Y
Individual pumps with over 100- head and a 50-hp motor shall be able to operate at 50% flow
with 30% power.
Y
The differential pressure shall be measured at or near the furthest coil or the coil requiring the
greatest pressure differential.
Exceptions include:
Y
Where minimum flow interferes with proper operation of the equipment (i.e., the chiller) and
the total pump horsepower is less than 75.
Y
Systems with no more than 3 control valves.
Cooling Tower Basics
Cooling towers are used in conjunction with water-cooled chillers. Air-cooled chillers do not require
cooling towers. A cooling tower rejects the heat collected from the building plus the work of
compression from the chiller. There are two common forms used in the HVAC industry: induced draft
and forced draft. Induced draft towers have a large propeller fan at the top of the tower (discharge
end) to draw air counterflow to the water. They require much smaller fan motors for the same capacity
than forced draft towers. Induced draft towers are considered to be less susceptible to recirculation,
which can result in reduced performance.
Figure 15 - Induced Draft Cooling Tower
Forced draft towers have fans on the air
inlet to push air either counterflow or
crossflow to the movement of the water.
Forward curved fans are often
employed. They use more fan power
than induced draft but can provide
external static pressure when required.
This can be important if the cooling
tower requires ducting, discharge cap or
other device that creates a pressure drop.
Condenser water is dispersed through
the tower through trays or nozzles. The
water flows over fill within the tower,
which greatly increases the air-to-water
surface contact area. The water is collected into a sump, which can be integral to the tower or remote
from the tower. The latter is popular in freezing climates where the condenser water can be stored
indoors.
Either tower type can have single or multiple cells. The cells can be headered together on both the
supply and return side with isolation valves to separate the sections. This approach allows more cells
to be added as more chillers are activated or to allow more tower surface area to be used by a single
chiller to reduce fan work.
Application Guide AG 31-003-1
15
Typical Operating Conditions
The Cooling Tower Institute (CTI) rates cooling towers at 78°F ambient wetbulb, 85°F supply water
temperature and a 10°F range. Since it is common (but not necessary) to use a temperature range of
10°F, the cooling tower flow rate will be 3.0 gpm/ton compared to the chilled water flow rate which is
2.4 gpm/ton. The extra condenser water flow rate is required to accommodate the heat from the work
of compression. Cooling towers are very versatile and can be used over a wide range of approaches,
ranges, flows and wetbulb temperatures. Lower condenser water temperatures can be produced in
many climates with low wet bulb temperatures which significantly improves chiller performance.
Figure 16 - Forced Draft Cooling Tower
Cooling Tower Process
Cooling towers expose the condenser water
directly to the ambient air in a process that
resembles a waterfall. The process can cool
condenser water to below ambient drybulb.
The water is cooled by a combination of
sensible and latent cooling. A portion of the
water evaporates which provides the latent
cooling. The example on page 18 shows the
cooling tower process on a psychrometric
chart at ARI conditions. As the wetbulb
temperature drops, cooling towers rely more
on sensible cooling and less on latent cooling.
Ambient air below freezing can hold very little
moisture which leads to large plumes; and in
some cases the winter tower selection requires
a larger tower than the summer conditions.
Additional care should be taken when
selecting cooling towers for use in winter.
16
Application Guide AG 31-003-1
Psychrometric Process for Cooling Towers
52.4 Btu/lb
0.029 lbw
42.4 Btu/lb
0.018 lbw
87.5 ºF
The above psychrometric chart shows the cooling tower process at ARI conditions.
Assume 1 lb. of water is cooled by 1 lb. of air. The water cools from 95°F to 85°F and
releases 10 Btus of heat to the air ( 1 Btu = the amount of heat required to raise the
temperature of 1 lb. of water, 1°F). The 10 Btus of heat raises the enthalpy of air from
42.4 Btu/lb. to 52.4 Btu/lb. and saturates the air. The leaving air condition is 87.5°F and
100% RH. The moisture content went from 0.018 lb.w to 0.029 lb.w. This means 0.0290.018 lb. = 0.011 of water was evaporated which is why it is common to hear that cooling
towers lose about 1% of their water flow to evaporation. The latent heat of vaporization
for water at 85°F is about 1045 Btu/lb. Multiplying the latent heat times the amount of
evaporated water (1045 x 0.011) results in 11.45 Btus of cooling effect. Cooling the
water required 10 Btus, the rest was used to cool the air sensibly. The air entered the
tower at 95°F and left the tower at 87.5°F.
Approximately 1% of the design condenser water flow is evaporated (See the above example). A
1000-ton chiller operating at design conditions can consume 1800 gallons of water per hour. The
specific amount can be calculated by reviewing the psychrometric process. In locations where the cost
of water is an issue, air-cooled chillers may provide a better operating cost despite the lower chiller
performance.
Winter Operation
Cooling towers required to work in freezing winter environments require additional care. The
condenser water must not be allowed to freeze particularly when the tower is idle. Common solutions
include electric or steam injection heaters or a remote sump within the building envelope. The high
RH of ambient winter air results in a plume, which can frost over surrounding surfaces. Low plume
towers are available. Finally, freezing of condenser water on the tower itself can lead to blockage and
reduced or no performance. Modulating water flow through a cooling tower (such as the use of threeway chiller head pressure control) should be given careful consideration. In many instances this can
lead to increased possibility of freezing the tower.
Application Guide AG 31-003-1
17
Water Treatment
Condenser water has all the right ingredients for biological growth; it is warm, exposed to air and
provides surfaces to grow on. In addition, the constant water loss makes water treatment even more
difficult. Both chemical and ozone-based treatment systems are used. A thorough discussion on the
topic of water treatment is beyond the scope of this Guide but it suffices to say, that it is necessary to
provide the proper operation of both the tower and the chiller.
Closed Circuit Coolers
Figure 17 - Chiller Power Vs. Tower Power
2500
Optimal
2000
Pow e r (kW )
Cooling towers differ from closed-circuit
coolers in that closed-circuit coolers
reject heat sensibly while cooling towers
reject heat latently. Consider ambient
design conditions of 95°F DB and 78°F
wb. If closed circuit coolers are used, the
condenser water must be warmer than the
ambient drybulb (typically 10°F warmer
or 105°F). This raises the condensing
pressure in the chiller and requires more
overall power for cooling. Closed circuit
coolers are larger than cooling towers for
the same capacity and can be difficult to
locate on the roof.
4
Total
1500
Chiller
1000
500
Tower
0
0.200
0.400
0.600
0.800
1.000
Re lativ e Tow e r Air Flow
Cooling Tower Controls
Cooling tower controls provide condenser water at the correct temperature to the chillers. Defining
correct water temperature is very important. Lowering the condenser supply water temperature (to the
chiller) increases the effort by the cooling tower and more fan work can be expected. It also improves
the chiller performance. Figure 17 shows the relationship between chiller and tower work.
Table 2 - Chiller Performance Vs. CSWT
Chiller Type
Performance
Improvement
(Percent kW /°F
condenser water)
W/C Recip.
W/C Scroll
W/C Screw
W/C Centrifugal
W/C Centrifugal VFD
Absorption
1.1 to 1.3
1.3 to 1.5
1.6 to 1.8
1.0 to 1.6
2.4 to 2.6
1.4 to 1.5
Table 2 shows the range of chiller
improvement that can be expected by
lowering the condenser water supply
temperature. The goal of cooling tower
control is to find the balance that provides
the required cooling with the least use of
power by the chiller plant.
Cooling towers are often provided with
aquastats. This is the most basic level of
control. They are popular for single
chiller–tower arrangements because the control package can be supplied as part of the cooling tower.
The aquastat is installed in the supply (to the chiller) side of the cooling tower. In many cases, the
setpoint is 85°F, which is very poor.
Figure 18 shows the 85°F setpoint and the ARI condenser relief curve which chillers are rated at.
Maintaining 85°F condenser water, while saving cooling tower fan work, will significantly penalize
the chiller. There is some risk that without some condenser relief, the chiller may not operate at lower
part load conditions (The chiller may surge).
4
Braun, J.E., and G.T. Diderrich. 1990. Near-Optimal Control of Cooling Towers For Chilled Water
Systems. ASHRAE Transactions SL-90-13-3, Atlanta, Ga.
18
Application Guide AG 31-003-1
Supply Condenser W ater
Tem perature
Figure 18- Chiller Performance with 85 T Setpoint
If aquastats are going to be used, then a lower
setpoint than 85°F should be used. One
90
ARI Setpoint
recommendation is to set the aquastat at the
85
minimum condenser water temperature
80
acceptable to the chiller. The cooling tower
75
will then operate at maximum fan power and
70
always provide the coldest possible (based on
65
load and ambient wet bulb) condenser water
60
to the chiller until the minimum setpoint is
reached. Then the tower fan work will stage
55
0
25
50
75
100
down and maintain minimum setpoint.
% Chiller Load
ARI 550/590
Max Allowable SCWT For Stable Operation
Supply Condenser W ater
Temperature
Figure 19 – Chiller Performance with Minimum Setpoint
Minimum chiller setpoints are not a specific
85
temperature. They change depending on the
chiller load. A conservative number such as
75
65°F is recommended.
65
Tower Fans
Modulate to
Maintain
Min SCWT
55
45
Tower Fans
Operate at Full
Speed
35
0
10
20
30
40
50
60
70
% Chiller Load
80
90
100
Another method to control cooling towers
dedicated to single chillers is to use the chiller
controller. Most chiller controllers today have
standard outputs which can operate cooling
towers, bypass valves and pumps. The chiller
controller has the advantage of knowing just
how much cooling is actually required by the
chiller for optimum performance.
A method to control either single cell or multiple cell cooling towers serving multiple chillers is to
base the condenser supply water temperature on ambient wetbulb. For this method, set the condenser
water setpoint at the current ambient
☺Tip: Using wetbulb plus tower design approach as
wetbulb plus the design approach
a setpoint can strike an excellent balance between
temperature for the cooling tower. The
chiller work and cooling tower fan work.
set-point will change as the ambient
wetbulb changes. Limit the setpoint
between the design condenser water temperature (typically 85°F) and the minimum condenser water
temperature (typically 65°F).
The wetbulb method will provide good condenser relief for the chiller and cooling tower fan work
relief when the chiller is not operating at 100% capacity. It can be a good balance between chiller and
tower work.
Ultimately, the best cooling tower control designs are part of a chiller plant optimization program.
These programs monitor the weather, the building load and the power consumption of all the
components in the chiller plant including cooling towers. Using modeling algorithms, the program
calculates the best operating point to use the least power possible and meet the requirements of the
building.
Application Guide AG 31-003-1
19
Cooling Towers and Energy Efficiency
Cooling towers consume power to operate the fans. Induced draft towers should be selected since
they typically use half the fan horsepower force draft towers use. Some form of fan speed control is
also recommended such as piggyback motors, multi-speed motors or Variable Speed Drives (VFDs).
In addition, a sensible controls logic is required to take advantage of the variable speeds.
ASHRAE 90.1-2001 requires the following for heat rejection devices:
Y
Requires fan speed control for each fan motor 7 ½ hp or larger. The fan must be able to operate
at two-thirds speed or less and have the necessary controls to automatically change the speed.
(6.3.5.2)
Exceptions include:
Y
Condenser fans serving multiple refrigeration circuits.
Y
Condenser fans serving flooded condensers
Y
Installations in climates with greater than 7200 CDD50.
Y
Up to one-third of the fans on a condenser or tower with multiple fans, where the lead fans
comply with the speed control requirement.
Load Basics
Figure 20 -Air Handling Equipment
Chilled water coils are used to transfer the heat from the building air to the chilled water. The coils
can be located in air handling units, fan coils, induction units, etc. The air is cooled and dehumidified
as it passes through the coils. The chilled water temperature rises during the process.
Cooling coil performance is not linear with flow. Cooling coils perform 75% cooling with only 50%
chilled water flow and 40% cooling with only 20% flow. As well, the leaving water temperature will
approach the entering air temperature as the load is reduced.
Process loads can reject heat in the chilled water in a variety of ways. A common process load is a
cooling jacket in machinery such as injection molding equipment. Here the chilled water absorbs the
sensible heat of the process.
Control Valve Basics
Control valves are used to maintain space temperature conditions by altering chilled water flow.
Valves can be broken down into groups in several ways. Valves can be two-position or modulating.
Two-position valves are either on or off. Control comes from time weighting. The percentage that
the valve is open over a certain time period dictates the amount of cooling that the cooling coil
actually does. Modulating valves vary the flow in response to the actual load at any given time.
Valves can also be classified as two-way or three-way type. Two-way valves throttle flow while three
divert flow. Refer to Piping Diversity, page 24 for further explanation. There are several different
physical types of valves. Globe valves, ball valves and butterfly valves are all commonly used in the
HVAC industry.
20
Application Guide AG 31-003-1
90%
50%
Heating Output
Design Flow
Heating Output
90%
50%
50%
10%
10%
50%
50%
Design Flow
90%
Stem Travel
50%
90%
Stem Travel
Figure 21 - Coil and Control Valve Performance Curves
Different kinds of valves have different valve characteristics. Common characteristic types include
linear, equal percentage and quick opening. Control valves used with cooling coils need to have a
performance characteristic that is “opposite” to the coil. Equal percentage control valves are typically
used for two-way applications. For three-way applications, equal percentage is used on the terminal
port and linear is used on the bypass port.
Figure 21 shows an equal percentage control valve properly matched to a cooling coil. The result is
that the valve stem movement is linear with the cooling coil capacity. In other words, a valve stroked
50% will provide 50% cooling.
Sizing Control Valves
Control valves must be sized correctly for the chilled water system to operate properly. An
incorrectly sized control valve cannot only mean the device it serves will not operate properly, it can
also lead to system-wide problems such as low delta T syndrome.
Control valves are typically sized based on the required Cv . The Cv is the amount of 60°F water that
will flow through the valve in US gpm, with a 1 PSI pressure drop. The formula is:
G = Cv (∆P)½
Where:
G is the flow through the valve in US gpm
Cv is the valve coefficient.
∆P is the differential pressure required across the control valve.
The required flow at a control valves is defined by the needs on the device (fan coil, unit ventilator or
AHU) it serves. Cv values for valves are published by valve manufacturers. The required pressure
differential through the valve is the difficult parameter to define.
Pressure Drop
Figure 22 - Pressure Drops and Cv
Application Guide AG 31-003-1
Control Valve PD Should
Be 50% Of Branch PD
Figure 22 shows typical pressure drops from the
supply to the return line for a cooling coil. For a
modulating valve, the valve pressure drop should
be as large a percentage as possible when
compared to the system pressure drop; preferably
over 50%. The reason is to maintain valve
authority. For on-off control, any valve can be
used as long as it can pass the required flow rate
with the pressure differential available.
21
Valve Authority
As a control valve closes, the
☺Tip: When calculating valve Cv to size valves, use at
pressure drop across the valve
least 50% of the system pressure drop from the supply to
increases so that when the valve is
the return line to maintain good valve authority. In most
completely closed, the differential
cases, a properly sized control valve will be smaller than
pressure drop across the valve
the line size it is installed in.
matches the pressure drop from the
supply to the return line. This pressure drop is known as ∆PMax . When the valve is completely open,
the pressure drop across the valve is at its lowest point and is referred to ∆PMin. The ratio (ß) ∆PMin /
∆PMax is the valve authority. The increase in pressure drop across the valve as it closes is important
to note. Valves are rated based on a constant pressure drop. As the pressure drop shifts, the
performance of the valve changes. The method to minimize the change in valve performance is to
maintain the Valve Authority (ß) above 0.5.
0.
1
=
A
Flow Rate, %
Figure 23 - Distortion of Equal Percentage Valve Characteristic
Figure 23 shows the change in the valve
100
characteristic that occurs at different Valve
90
Authorities. Since the goal is to provide a
80
valve with a performance characteristic that
70
is the opposite of a coil characteristic (See
60
2
.
Figure 21), it is important to maintain Valve
0
50
=
5
A
0.
Authority above 0.5.
=
40
A
A
30
=
1
20
10
0
0
20
40
60
80
100
Valve Lift, %
Valve Authority Example
Consider a control valve with a Cv = 25 serving a coil that has a design flow of 50 US
gpm. The pressure differential from the supply to the return line is 16 PSI.
As the valve closes, the system pressure shifts to the valve until all the pressure drop
(16 PSI) is across the valve. If the valve was fully opened and there was 16 PSI
across the valve the flow rate would increase to:
½
Q = Cv (∆P) = 25(16)
½
= 100 US gpm.
This does not actually happen, however, since the pressure drop through the coil,
balancing valve, etc. increases and limits flow to 50USgpm.
∆PMin = (Q)²/( Cv)² = (50)²/( 25)² = 4 PSI
In this case, the valve authority (ß) is 4 PSI/16 PSI = 0.25. Referring to Figure 23, it
can be seen that the valve performance characteristic is distorted and when matched
to a cooling coil will not provide a linear relationship between valve position and coil
output. This can lead to poor coil performance and low delta T syndrome. The
solution is to try and keep the valve authority above 0.5. In other words, the pressure
drop though the control valve when it is fully open should be at least 50% of the
pressure drop from the supply to return line.
22
Application Guide AG 31-003-1
Rangeablity
Rangeablity is a measure of the turndown a control valve can provide. The larger the range, the better
the control at low loads. Typical ranges for control valves are 15:1 to 50:1.
Control Valve Location in Systems
Proper valve selection requires knowing the pressure drop from the supply to the return wherever the
device is located. This information is typically not made available to the controls contractor which
often leads to guessing. One solution would be for the designer to provide the required Cv for each
valve. Another solution would be to provide the estimated pressure drops for each valve. Because
the pressure drop from the supply to the return changes throughout the system, it can be expected that
different valves with different Cvs will be required. Even if all the coil flows and pressure drops were
identical, the valves should change depending on location in the system. Lack of attention to this
detail can lead to low delta T syndrome (refer to Low Delta T Syndrome, page 80) that can be very
difficult to resolve.
Loop Control Basics
There are two parameters that need to be considered for the chilled water loop. These are
temperature and flow. The loop supply temperature is usually controlled at the chiller. The unit
controller on the chiller will monitor and maintain the supply chilled water temperature (within its
capacity range). The accuracy to which the chiller can maintain the setpoint is based on the chiller
type, controller quality (a DDC controller with a PID loop is the best), compressor cycle times, the
volume of fluid in the system, etc. Systems with fast changing loads (especially process loads) and
small fluid volumes (close coupled) require special consideration.
The system flow control occurs at the load. To control the cooling effect at the load, two-way or
three-way valves are used. Valve types are discussed in Control Valve Basics, page 20. Valve
selection will also touch on piping diversity and variable vs. constant flow.
Another method to control cooling is face and bypass control at the air cooling coil while running
chilled water through the coil. This approach has the advantage of improved dehumidification at part
load and no waterside pressure drops due to control valves. The disadvantage is the requirement for
continuous flow during any mechanical cooling load. In many cases the pressure drop savings will
offset the continuous operation penalty but only annual energy analysis will clarify it. Face and
bypass coil control is popular with unit ventilator systems with their required high percentage of
outdoor air, and make-up air systems.
Application Guide AG 31-003-1
23
Piping Diversity
Figure 24 - Three-way Valves
Diversity in piping is based on
what type of valves are used.
To maintain the correct space
Flow Is Constant At Each Coil
condition, three-way or two-way
Delta T Changes With Load
control valves are used. Threeway control valves direct chilled
water either through or around
the coil to maintain the desired
condition. If all the loads on the
CW Pump Sized For
loop use three-way valves, then
Connected Flow
the chilled water flow is
constant.
The temperature
range
varies
directly with the
44F Supply
load. That is, if the design
chilled water temperature range
Coil
Chiller
Chiller Sized For
is 10°F, then every 10% drop in
Peak Load
3 Way Valve
system load represents a 1°F
drop in temperature range. A
system incorporating three-way control valves is easy to design and operate. The system pumps all the
water all the time, however this requires more pump horsepower. In most cases the chiller is sized for
the building peak load. Due to diversity, not all the connected loads will “peak” at the same time as
the building peak load. However, the pumps and piping system must be designed for full flow to all
the control valves all the time. Since the chiller flow rate is the same as the flow rate through all the
loads (they’re connected by the same piping system and pump) the diversity is applied to the chiller
temperature range.
Coil Bypass
Line
Figure 25 - Two-Way Valves
Temperature Range Across
Load Remains Constant.
Flow Varies With Load
CW Pump Sized For
Chiller Flow Rate
At Design Delta T
For example, consider a building
with an 80-ton peak load.
Summing all the connected loads
adds up to 100 tons. In short,
this building has a diversity of
80%. Using a temperature range
of 10°F at each control valve, the
total system flow rate is:
Flow = 24 x 100 tons/10°F =
240 gpm
However, an 80-ton chiller with
240 gpm will only have a
Chiller Sized For
temperature range of 8°F. The
Peak Load
2 Way Valve
lower chiller temperature range is
not a problem for the chiller
operation, but it will lower the chiller efficiency. Care must be taken to select the chiller at the proper
temperature range.
When two-way modulating control valves are used, the flow to the coil is restricted rather than
bypassed. If all the valves in the system are two-way type, the flow will vary with the load. If the
valves are properly selected, the temperature range remains constant and the flow varies directly with
the load. In this case the diversity is applied to the chilled water flow rate.
24
Application Guide AG 31-003-1
Using the previous example, the peak load is 80 tons and the design flow is 2.4 x 80 tons or 192 gpm.
The connected load is still 100 tons and requires 240 gpm if all the two-way control valves are open at
the same time. The 80% diversity assumes only 80% of the valves will be open at the peak load.
The advantage of two-way control valves is both the pump and the piping are sized for a smaller flow
rate, offering both first cost and operating savings. The difficulty is that the chiller and control system
must be designed for variable flow. The chiller has a minimum flow rate so the piping design has to
allow for enough flow during all operating conditions to meet the chiller minimum flow rate. Using
two-way valves is the main building block for a variable flow system.
Water Temperatures and Ranges
Selection of temperature ranges can affect the chiller plant operation and energy usage. The limiting
temperatures are the required supply air temperature and either the ambient wetbulb (water or
evaporatively cooled chillers) or drybulb (air cooled chillers) temperatures. Once these have been
identified, the HVAC system must operate within them.
Supply Air Temperature
The chilled water supply temperature is tied to the supply air temperature. The chilled water
temperature must be cold enough to provide a reasonable log mean temperature difference (LMTD)
(Refer to McQuay AG 31-002, Centrifugal Chiller Fundamentals, for more information on LMTD)
for a cooling coil to be selected. Traditionally this has resulted in a 10°F approach which, when
subtracted from 55°F supply air temperature, has led to the 44 or 45°F chilled water temperature.
Lowering the chilled water temperature will increase the approach allowing a smaller (in rows and
fins and hence air pressure drop) coil to be used. It will also increase the lift that the chiller must
overcome and that will reduce the chiller performance.
Figure 26 - Chiller Heat Exchanger Conditions
97°F
118.3 psig
R-134a
θ2
HEAT OF
CONDENSATION
θ1
CO
LIFT
(°F)
R
SE
EN
ND
ID
FLU
E
ATUR
PER
TEM
T2
95°F
85°F T1
54°F T1
CO
OL
ER
FLU
ID T
E
MPE
R
θ1
ATUR
E
T2
HEAT OF
VAPORIZATION
42°F
36.6 psig
R-134a
Application Guide AG 31-003-1
SATURATED SUCTION TEMPERATURE {TR}
44°F
θ2
The air pressure drop savings for small
changes (2 to 4°F) in the approach do not
generally save enough in fan work to
offset the chiller penalty.
This is
particularly true for VAV where the
pressure drops inside an air handling unit
follow the fan affinity laws. The power
required to overcome the coil pressure
drop decrease by the cube root as the air
volume decreases. A 20% decrease in
airflow results in a 36% decrease in
internal air pressure drop and a 49% drop
in bhp.
It is sometimes suggested that the chilled
water supply temperature be 2°F colder
than the supply water temperature used to
select the cooling coils to make sure the
“correct” water temperature is delivered
to the coils. This is not recommended.
For a 10°F chilled water temperature
range, a 2°F temperature increase implies
25
20% of the chiller capacity has been lost to heat gain in the piping system! The coil would have to be
selected with only an 8°F chilled water temperature range. With the exception of extremely large
piping systems, there is very little temperature increase in a properly designed and installed system.
Chilled Water Temperature Range
Increasing the chilled water temperature range reduces the required flow rate and consequently the
pump and piping sizes. In some situations, the savings both in capital cost and operating cost can be
very large. Increasing the chilled water temperature range while maintaining the same supply water
temperature actually improves the chiller performance because the chiller log mean temperature
difference increases. It has just the opposite effect on the cooling coil where the LMTD decreases
between the air and the chilled water. In some cases, it may be necessary to lower the supply water
temperature to balance the chiller LMTD with the coil LMTD.
Table 3 - Suggested Supply Water Temperatures
Table 3 provides suggested supply water
temperatures for various ranges. The best
Chilled Water
Suggested Supply
balance of supply water temperature and
Temperature Ranges (°F)
Water Temperature (°F)
range can only be found through annual
10
44
12
44
energy analysis. Every project is unique.
14
42
The McQuay Energy Analyzer™ can be used
16
42
to quickly evaluate the pump savings vs.
18
40
chiller penalty.
Products such as fan coils and
☺Tip: Pump operating savings come from increasing the
unit ventilators have standardized
chilled water temperature range, not from lowering the supply
coils designed to work with 10 to
water temperature.
12°F chilled water range. When
these products are used with this
range of chilled water, they provide the sensible heat ratio and return water temperature generally
required. When the range is increased, the coils may not provide the necessary sensible heat ratio and
return water temperature. It is recommended that for these products, the chilled water range stay
close to industry standard conditions. Chilled water coils are designed for the application-specific
conditions so this is generally not an issue.
Condenser Water Temperature Range
Increasing the condenser water temperature range reduces the condenser water flow, which requires
smaller pumps and piping. It also increases the required condenser pressure while improving the
LMTD for the cooling tower. Increasing the condensing pressure on the chiller will result in a
combination of increased chiller cost and reduced performance. Improving the cooling tower LMTD
allows a smaller tower to be used, but the savings from this strategy will not generally offset the
increased cost of the chiller.
In most cases, the overall design power requirement will go up. At full load conditions, the increased
chiller power requirement to overcome the increased lift will more than offset the savings from the
smaller cooling tower fan and condenser pump. This will depend on the head requirement of the
condenser pump.
As the chilled water load decreases, the chiller and cooling tower work will reduce but the condenser
pump work will remain the same. At some part load operating point, the savings from the smaller
condenser pump will offset the chiller penalty and for all operating points below this, the increased
condenser range will save energy. Whether an increased condenser temperature range will save
energy annually will depend on when the crossover point occurs (the pump motor size) and the chiller
operating profile (whether the operating hours favor the chiller or the pump). This can only be found
with annual energy analysis.
26
Application Guide AG 31-003-1
Temperature Range Trends
Changing the temperature ranges and supply temperatures requires careful analysis. The following
are some points to consider:
Y
The traditional ARI operating conditions work very well for many buildings.
Y
Unnecessary reduction of the chilled water supply temperature should be avoided as it increases
chiller work.
Y
When using standard products such as fancoils and unit ventilators, maintain the chilled water
temperature range between 10 and 12°F where they are designed to operate.
Y
Increasing the chilled water temperature range is a good way to reduce the capital and operating
cost of a building, particularly if the pump head is large or the piping runs long.
Y
With larger chilled water temperature ranges it may be necessary to lower the supply water
temperature to find a balance between coil and fan performance vs. chiller performance. Annual
energy analysis using the McQuay Energy Analyzer™ is recommended.
Y
If the chilled water supply temperature is reduced, consider oversizing the cooling tower to
reduce the condenser water temperature and minimize the affect on the chiller.
Y
Always take into account the actual design ambient drybulb or wetbulb conditions when
designing a chiller plant. If the location is arid, then lower the wetbulb design as per ASHRAE
design weather data and select both the cooling tower and chiller accordingly.
Y
For very large chilled water ranges, use series chillers possibly with series counterflow condenser
circuits to optimize chiller performance.
Y
Increasing the condenser water range should only be considered for projects where the piping
runs are long and the pump work high. When it is required, optimize the flow to the actual pipe
size that is selected and select the chillers accordingly. Consider oversizing the cooling towers to
minimize the affect on the chiller.
Y
Use the McQuay Energy Analyzer™ to evaluate various temperature range supply water
temperature combinations. Design condition performance is not an accurate indicator of the
annual energy usage.
Application Guide AG 31-003-1
27
Air and Evaporatively Cooled Chillers
The choice of chiller type and chiller plant design are inherently linked. Different chiller types have
different strengths and by careful selection of chiller plant design, these strengths can be optimized.
Most large plants consist of centrifugal water cooled chillers. Hybrid plants (discussed in Hybrid
Plants, page 66) may also include absorption chillers.
Air-Cooled Chillers
Figure 27 - McQuay Air-Cooled Screw Chiller
Many small to medium chiller plants use
air cooled chillers with air-cooled screw
chillers being common in the 150 to 400ton range. Air-cooled screw chillers offer
very good performance particularly at part
load. The compressors are modulating
rather than stepped which provides more
accurate control.
Air cooled chillers avoid the need for
cooling towers, condenser pumps and
condenser piping which can offer
substantial capital savings. Air cooled
chillers do not require mechanical room
space which offers additional savings.
Another advantage of aircooled chillers is they do not
☺Tip: Air cooled chillers do not require mechanical room space.
consume water like waterTo estimate the savings use$50/ft².
cooled chillers. A 400-ton
chiller will consume over 700 gallons per hour to offset cooling tower makeup. Where water is
scarce, this can be a significant cost. In addition, condenser water treatment is avoided.
Drybulb Relief
Air-cooled chillers have lower performance (consume more power) than water or evaporatively
cooled chillers because of the increased lift. Refrigeration work is proportional to lift; doubling the
lift will approximately double the
work required. (For this purpose,
☺Tip: When considering air cooled vs. water cooled it is
consider lift to be the difference
important to make an apples-to-apples comparison. Airbetween chilled water supply and
cooled chillers are rated with the condenser fans included. To
either cooling tower supply or
be fair, water-cooled chillers should have the condenser pump
ambient air drybulb) Since airand the cooling tower fans added. For instance, a watercooled chillers must raise the
cooled chiller with 0.55 kW/ton performance changes to 0.64
refrigerant temperature above
kW/ton when the condenser pumps and tower fan motor are
ambient drybulb, they consume
more power.
Both chiller types will improve chiller performance when the lift is reduced. This is often referred to
as condenser relief. Figure 28 shows the annual drybulb vs. wetbulb temperature for Chicago. The
curves show the amount of available condenser relief for each type of chiller. As expected, the
wetbulb based (water-cooled) chillers offer the best performance at design conditions, however, the
relief during spring and fall seasons quickly reduces the difference. In the winter, there is no
advantage, as either system will operate at the minimum condensing temperature permissible by the
refrigeration system.
28
Application Guide AG 31-003-1
Understanding the overall annual performance is important when considering the building use. For
example, schools are rarely operating at design conditions during the summer months due to reduced
occupancy. This has the effect of limiting the advantage water-cooled chillers have over air- cooled
chillers.
Figure 28 - Annual Ambient Drybulb Vs. Wetbulb
Water-cooled chiller systems
usually out perform air cooled
chiller systems. However, when
considering life cycle analysis, the
payback for water-cooled systems
can be very long.
80.0
Temperature (F)
70.0
60.0
50.0
Winter Operation
40.0
In climates where freezing
conditions exist, winter operation
must be considered. There are
20.0
two issues to deal with. The first
is the necessary changes to the
chiller to operate in cold
Average Daily DB
Average Daily WB
temperatures. All chillers have a
minimum condensing temperature. Going beyond that temperature may damage the chiller. To
protect the chiller, the condensing fans are staged off, or slowed down to maintain the correct
condensing temperature. In very cold climates, a flooded system may be required. There are other
changes that are required as well, such as larger crankcase heaters. Consult your sales representative
to discuss these requirements.
r
D
ec
em
be
be
r
r
N
ob
e
O
ct
ov
em
r
t
be
gu
s
Ju
ly
pt
em
Se
Au
ay
Ju
ne
M
ch
Ap
ri l
ua
ry
ar
M
nu
ar
Ja
Fe
br
y
30.0
The second issue is protecting the chilled water from freezing. Here are some possible solutions:
Y
Heat trace the piping and evaporator. This is a good solution where freezing weather occurs but
is not extensive. It is also a good backup for systems that are to be drained in the winter. Many
chillers already include evaporator tracing. Check with your sales representative.
Y
Add antifreeze. A common solution is to add either propylene or ethylene glycol to the chilled
water. While this will resolve the freezing issue, it will increase pumping work and de-rate both
the chiller and chilled water coils. Maintaining the correct level of antifreeze in the system
becomes an additional maintenance issue. A loss of antifreeze in the system due to flushing or a
leak and subsequent water make-up can allow the chilled water loop to become vulnerable to
freezing. Adding glycol to a system that was not designed to have it must be carefully examined
to ensure the system will operate properly.
Y
Relocate the evaporator barrel inside the building envelope. Relocating the evaporator avoids
antifreeze but will require field refrigerant piping. There are also limitations on piping distances
and elevation changes. Consult your sales representative to discuss the details.
Y
Use an indoor chiller with a remote air-cooled condenser. This arrangement will require
mechanical room space, however, the equipment can be serviced from within the building. This
is a very good solution for very cold climates. The compressors are indoors and flooded
condensers can easily be added.
Air-Cooled Chiller System Design
Air-cooled chillers will affect the system selection and design details. In most cases, air-cooled
chillers are limited in evaporator shell arrangements when compared to centrifugal chillers. They are
designed to work well around the ARI 550/560 design conditions (54°F EWT, 44°F EWT). The
design temperature range should stay within 20% of these operating conditions. Series chiller
arrangements will typically double the flow and half the temperature change in the evaporator. This
Application Guide AG 31-003-1
29
can lead to very high water pressure drops. Contact your sales representative to review the acceptable
performance ranges of the various chiller options.
Air-cooled chillers can be used in any chiller system design. They are commonly used in single,
parallel and primary/secondary systems. They can be mixed with water cooled chillers in multiple
chiller applications.
Most air-cooled chillers can be used in either constant or variable flow applications. Variable flow in
the evaporator is a function of the staging and chiller controller. Check with your sales representative
when designing variable primary flow systems.
There are many applications that require a small amount of chilled water during the winter. For
example, a hospital might require chilled water to cool an MRI year-round while the AHUs can
switch to air-side economizers in the winter. When there is a requirement for small amounts of chilled
water in winter, an air-cooled chiller is an excellent solution. An air-cooled chiller avoids the need to
operate a cooling tower in cold (freezing) weather. In addition, the air-cooled chiller will offer equal
performance to a water-cooled chiller at low ambient conditions.
Evaporatively Cooled Chillers
Evaporatively-cooled chillers are essentially water-cooled chillers in a box. The hot gaseous
refrigerant is condensed by water flowing over the condenser tubes and evaporating. This ties the
condensing temperature to ambient wetbulb like a water-cooled chiller. The condenser, water sump
and pump, etc., are all integral
to the chiller. Whereas a water☺Tip: Evaporatively -cooled chillers are not just for hot, dry
cooled chiller will require a
climates, should be considered wherever water-cooled chillers
cooling tower, condenser pump
make sense.
and field erected piping, the
evaporatively-cooled chilled comes as a complete package from the factory. Evaporatively-cooled
chillers offer the ease and savings of air-cooled chiller installation while providing performance
comparable to water-cooled chillers. Evaporatively-cooled chillers will require makeup water, water
treatment and drains.
Figure 29 - McQuay EGR Evaporatively Cooled Chiller
Evaporatively-cooled chillers are often
associated with hot, dry climates such as
the American Southwest. However, they
should be considered wherever watercooled chillers make sense.
Evaporatively Cooled Chiller
System Design
Evaporatively-cooled chillers can be used
in any system design. They have similar
limitations as air-cooled chillers (Refer to
Air-Cooled Chiller System Design, page
29).
30
Application Guide AG 31-003-1
Dual Compressor and VFD Chillers
The unique performance of both McQuay dual compressor and variable frequency drive chillers affect
the chiller plant design. While it is satisfactory to simply switch conventional chillers with either dual
or VFD chillers in the chiller plant, to take full advantage of these chillers capabilities, the design
should be modified.
Dual Compressor Chillers
Figure 30 - McQuay Dual Compressor Chiller
McQuay
dual
compressor
centrifugal chillers offer many
advantages over conventional
chillers. From a performance
point of view, the chiller is most
efficient at 50% capacity. At this
point, only one compressor is
operating and the evaporator and
condenser are twice the size
normally used for the compressor
size. Whereas a conventional
chiller NPLV can be 0.479
kW/ton, a dual NPLV is 0.435
kW/ton. An advantage a dual
compressor chiller offers over a
VFD chiller is it does not require significant condenser water temperature relief to provide the
savings. Dual chillers can also have VFD offering the best of both worlds with an NPLV of 0.360
kW/ton or lower.
The built-in redundancy of a dual compressor chiller allows the designer to use fewer chillers and still
provide the owner with backup equipment. This can save considerable capital expense in installation
costs.
VFD Chillers
Figure 31 - VFD Chiller
VFD chillers use a combination of
VFDs and inlet guide vanes to
modulate the capacity of the chiller.
The VFD is used to change the speed
of the compressor. For information
on how this works, refer to McQuay
AG 31-002, Centrifugal Chiller
Fundamentals.
The performance
savings are obtained when the VFD is
used rather than the inlet guide vanes.
Typical VFD chiller NPLV is about
0.386 kW/ton. The VFD can only be
used when the lift on the compressor
is reduced. The lift is reduced either
when the chiller load is decreased or
when the condenser water temperature is lowered and/or the chilled water temperature is raised.
When the lift is reduced and the VFD can be used, the chiller will operate much more efficiently at
part load than a conventional chiller does.
Application Guide AG 31-003-1
31
The best way to take advantage of a VFD chiller is to reduce the condenser water temperature as
much as possible. Climates with reasonable annual changes in wetbulb are prime candidates for VFD
chillers.
System Design Changes
Conventional Application
Both dual compressor and VFD chillers operate much more efficiently at part load. Conventional
chillers operate most efficiently at or near full load. To fully optimize a dual or VFD chiller, the
design should take advantage of their part load performance.
Figure 32 - Chiller Performance Vs. Plant Load
1.2
1
KW/Ton
0.8
0.6
0.4
0.2
0
0
20
40
60
80
100
% Chiller Plant Load
Two Single Chillers
Two Dual Chillers
Figure 32 is based on two equally sized chillers in a primary/secondary arrangement using the ARI
condenser relief profile for the entire plant. At the 50% load point, the second chiller must be started.
For conventional chillers, the chiller performance drops because the load is split evenly between the
two chillers and they unload to a less efficient operating point. The dual and VFD chillers actually
improve their performance because the chillers are unloaded and there is condenser relief available.
Considering that most buildings experience a significant number of operating hours around 50% plant
load, the dual or VFD chillers may offer appreciable savings even when used in a convention manner.
Lead Chiller Application
The first chiller that is activated in a plant, typically called the lead chiller, operates with many hours
at reduced load and condenser water temperature. An example is a multi-chiller primary /secondary
plant. The lead chiller sees optimal conditions for either a VFD or a dual compressor chiller. The
other chillers in the plant can be conventional chillers. Each chiller that is started as the plant load
increases will operate at a higher percent load with less condenser water relief and therefore will offer
fewer savings.
Winter Load Application
Another good application for a dual or VFD chiller is winter load applications. Building using
fancoils have considerable chiller plant loads even in winter. Other buildings such as hospitals or
office buildings with computer, telecommunications or other winter chilled water loads can also take
32
Application Guide AG 31-003-1
advantage of a dual or VFD chiller. In many cases, these winter loads are relatively small.
Conventional thinking would require a smaller chiller sized specifically for the load. With a dual or
VFD chiller, there may not be a performance penalty to use a larger chiller sized for summer loads to
handle the small winter load. The peripheral loads such as pumps should be checked when evaluating
performance.
Series Chiller Application
A common method for sizing chillers used in series is to select both chillers to be able to perform as
the lead chiller (See Series Chillers, page 44). The causes the lag chiller to be sub-optimized because
the lift is reduced in the lag position. By using a VFD chiller as the upstream chiller, the VFD can
take advantage of the reduced lift when operating as the lag chiller. In addition, the same chiller can
be used as the lead chiller during light loads when there should be condenser water relief available.
Asymmetrical Chiller Application
Selecting the chillers to be different sizes can improve chiller plant performance based on the building
load profile (see Varying Chiller Sizes, page 57). Using either a dual or VFD chiller for that larger
chiller can enhance the savings. Consider a 1200-ton plant consisting of an 800-ton dual compressor
and a 400-ton single compressor chiller. The dual compressor chiller can accommodate the plant load
up to 800 tons. Above that, the second chiller must be started and both chillers will initially operate
at 67%. The larger chiller will be more efficient when unloaded.
Low Delta T Application
Most variable flow chiller plants will see a drop in return water temperature as the load drops. The
low delta T can cause serious operation issues with the plant ( See Low Delta T Syndrome, page 80).
One solution is to use either dual or VFD chillers and operate two chillers at part load as opposed to
one chiller fully loaded. The dual or VFD chillers partly loaded should be more efficient than one
conventional chiller fully loaded. The chiller savings can be used to offset the additional pumping
cost from operating peripheral pumps. Moreover, this arrangement will provide the necessary chilled
water flow on the primary side to offset the low delta T problem.
Total System Analysis
When estimating the savings, consider both the type of chillers used and the available lift reduction
(condenser relief) and peripheral equipment that must be operated. Many combinations of plant
design can be quickly modeled using the McQuay Energy Analyzer™.
Application Guide AG 31-003-1
33
Mechanical Room Safety
Chillers represent large, powerful machines filled with refrigerants. When chillers are placed in
confined spaces, care must be exercised to provide safety to the equipment operator and the public at
large.
Figure 33 - ASHRAE STD 15-2001
ASHRAE Standard 15-2001, Safety Standard for
Refrigeration Systems and ASHRAE Standard 342001, Designation and Safety Classification of
Refrigerants, provides the designer with excellent
sources when designing a chiller mechanical room. In
Canada, CSA –B52, provides similar information.
The following is a brief summary of the safety
requirements covered by these documents as they apply
to chiller mechanical rooms. This section is by no
means a complete review of all requirements covered
by these standards. It is recommended that the design
have access to these documents. ASHRAE plans to
publish a users manual for Standard 15, which may also
be very helpful.
Standard 34
Standard 34 lists refrigerants and provides a safety
classification as shown in Figure 34. Refer to Standard
34 or to McQuay Application Guide AG 31-007,
Refrigerants for further information on common refrigerants and their safety properties.
Figure 34 - ASHRAE STD 34 Safety Classification
Standard 15
The purpose of Standard 15 is to specify “safe
design, construction, installation, and operation
of refrigeration systems6.” The following is a
brief outline of the issues that affect chiller
mechanical room design. The Section numbers
refer to ASHRAE Standard 15 sections.
Higher
Lower
Toxicity
Higher
Toxicity
A3
B3
A2
B2
A1
B1
5
Flammability
Lower
Flammability
No
Flame
Propagation
5
ASHRAE, 2001. ANSI/ASHRAE Standard 34-2001,Designation and Safety Classification of
Refrigerants. Atlanta, Ga.: ASHRAE
6
ASHRAE, 2001. ANSI/ASHRAE Standard 15-2001,Safety Standard for Refrigeration Systems.
Atlanta, Ga.: ASHRAE
34
Application Guide AG 31-003-1
Occupancy Classification
(Section 4)
Standard 15 identifies seven occupancy types (4.1.1 to 4.1.7) that consider the ability of the occupants
to respond to a potential exposure to refrigerant. An example is Institutional Occupancy where it is
anticipated that the occupants may be disabled and not capable of readily leaving the building without
assistance. A hospital is an institutional building.
Refrigeration System Classification (Section 5)
Section 5 describes various types of refrigeration systems based on how they extract or deliver heat.
Chiller plants are considered indirect systems because they cool chilled water, which in turn cools the
air. Indirect systems are subsequently subdivided by how the secondary fluid (chilled water) contacts
the air stream. Assuming coils are used, the classification is indirect closed system (5.1.2.3). If open
spray coil systems are used then the classification becomes either indirect open spray system (5.1.2.1)
or double indirect spray system (5.1.2.2).
The refrigeration system classification is used to determine the probability that a refrigeration leak
would enter the occupied space. Indirect closed systems such as chiller plants are generally
considered Low-Probability systems (5.2.2) providing they are either outside the building or in a
mechanical room.
Refrigeration Safety Classification (Section 6)
Standard 15 uses the safety classifications listed in Standard 34. Table 4 of this Guide is based on
Table 1 in Standard 15. It shows the group, refrigerant name, formula and the minimum quantity of
refrigerant allowed in an occupied area. Blends such as R-407C and R-410a are classified based on
the worst case fractionation of the refrigerant.
7
Table 4 - STD 15 Refrigerants and Amounts
Refrigerant
Number
Chemical Name
R-11
R-12
R-22
R-134a
Trichlorofluoromethane
Dichlorodifluoromethane
Chlorodifluoromethane
1,1,1,2-Tetrafluoroethane
R-123
2,2-Dichloro-1,1,1Trifluoroethane
Chemical
Formula
Quantity of Refrigerant per Occupied Space
Lb./1000 ft³
PPM (Volume)
Group A1
CCl3F
CCl2F2
CHClF2
CH2FCF3
Group B1
1.6
12
9.4
16
4,000
40,000
42,000
60,000
CHCl2CF3
0.40
1,000
Restrictions on Refrigeration Use (Section 7)
Section 7 describes the restrictions on where refrigerants can be used. It is based on results of
Sections 4, 5 and 6. With high probability systems (the refrigerant can enter the occupied space i.e. a
spot cooler) the maximum refrigerant level is defined in Table 1 of Standard 15 (7.2). For example
R-123 can only have a concentration of 0.4 lb per 1000 ft³ occupied space. Once these levels are
exceeded, the refrigeration equipment must be either outdoors or in a mechanical room (7.4).
Refrigerant levels involved in chiller plants necessitate mechanical rooms or outdoor equipment.
An interesting issue occurs when an air handling unit that serves occupied spaces is in the chiller
mechanical room. If a leak occurs, the refrigerant may be drawn into the air handling unit and
circulated through the building. The best solution to this is to avoid air handling units in the chiller
7
ASHRAE, 2001. ANSI/ASHRAE Standard 15-2001,Safety Standard for Refrigeration Systems.
Atlanta, Ga.: ASHRAE
Application Guide AG 31-003-1
35
mechanical room. This may not be possible in existing buildings. Standard 15 does allow AHUs in
the chiller mechanical room if they are sealed (8.11.7).
Installation Restrictions (Section 8)
Section 8 describes the installation requirements. It has general requirements (8.1 through 8.10) and
then requirements for nonflammable (type A1 and B1) refrigerants (8.11). Flammable refrigerants are
covered in 8.12 through 8.14. With the exception of ammonia, most common commercial air
conditioning refrigerants are either A1 or B1 type. It is important to confirm this, however.
The following is a summary of section 8:
Y
Foundations for refrigeration equipment shall be non-combustible and capable of supporting the
weight (8.1).
Y
Provide guards for moving machinery (8.2).
Y
There should be safe access to the equipment for service (8.3).
Y
Water, electrical, natural gas and duct connections must meet the requirements of local authority
(8.4, 8.5, 8.6 and 8.7 respectively).
Y
Refrigeration components in the air stream must be able to withstand 700°F without leaking.
Y
There are requirements on where refrigeration piping may be located (8.10).
Y
Other equipment is not prohibited in the chiller mechanical room unless specifically mentioned.
The room must be large enough to allow service and have a clear headroom of 7.25 ft. (8.11.1).
Y
The mechanical room doors shall be tight fitting that open outward and be self closing if they
open into the building. There must be enough doors to allow adequate escape in the event of an
emergency. The mechanical room cannot have openings that will allow refrigerant to enter the
occupied space in the event of leak (8.11.2).
Y
Each mechanical room shall have a refrigerant leak detector. The detector shall activate an alarm
and ventilation system at a value not greater than the TLV-TWA of the refrigerant. The alarms
shall be audio and visual and be located in the mechanical room and at each entrance to the
mechanical room. There shall be a manual reset located in the mechanical room. Absorption
chillers using water as the refrigerant do not require detectors (8.11.2.1).
Y
Chiller mechanical rooms shall be vented to the outdoors as follows (8.11.3 through 8.11.5):
Y
Mechanical fans are required.
Y
Openings for inlet air must be provided and situated to avoid recirculation.
Y
Supply and exhaust air ducts shall serve no other area.
Y
Discharge of exhaust air shall be in such a manner as not to cause a nuisance or danger.
Y
The emergency ventilation capacity shall be calculated as follows:
Q = 100*G0.5
Where
Q = the airflow rate in cubic
feet per minute
☺Tip: The refrigerant charge of a chiller can be supplied
by the chiller manufacturer. A good rule of thumb is 3 lbs.
per ton.
G = the mass of refrigerant in pounds in the largest system (i.e., the chiller), any of which is
located in the chiller mechanical room.
Y
Y
36
General ventilation shall be provided when occupied at a rate of 0.5 cfm/ft² or 20
cfm/person. The general ventilation rate must be capable of maintaining a minimum 18°F
temperature rise above the inlet air or a maximum space temperature of 122°F.
Natural ventilation is acceptable under certain circumstances such as open structures. Consult
Standard 15 for information.
Application Guide AG 31-003-1
Y
No open flames that use combustion air from the chiller mechanical room are allowed; for
instance a natural draft boiler. Combustion equipment can be in the chiller mechanical room if:
Y
Combustion air is drawn directly from outdoors or a refrigerant detector is used to shut down
the combustion device in the event of a leak (8.11.6).
Y
There shall be no airflow from the occupied space through the chiller mechanical room unless the
air is ducted and sealed in such a manner as to prevent refrigerant leakage from entering the
airstream. Access doors must be gasketed and tight fitting (8.11.7).
Y
Access to chiller mechanical rooms shall be restricted to authorized personnel and clearly marked
as restricted (8.11.8).
Y
The discharge from purge systems (i.e., negative pressure centrifugal chillers) shall be governed
by the same rules as pressure relief and fusible plug devices. Absorption chillers using water as
the refrigerant are exempt (8.14).
Design and Construction of Equipment and Systems (Section 9)
Section 9 covers the design and construction of refrigeration equipment. In most cases, the chillers
are factory built and the designer will not be directly involved in the equipment design. If there is
field refrigerant piping involved such as in a split system, the designer will have to be familiar with
this section.
Pressure Relief Piping
One area that will involve the designer is pressure relief devices and piping. The pressure relief
devices are typically part of the chiller. With field refrigerant piping, additional relief devices may be
required. Medium to high pressure refrigeration systems typically use re-seating spring loaded
pressure relief valves. Negative pressure chillers often use rupture disks. Rupture disks are less
expensive however, if they burst, the entire charge will be lost. Spring loaded pressure relief valves
will re-seat as soon as the pressure within the refrigeration system drops to safe level. For negative
pressure chillers, it is recommended that reseating pressure relief valves be used in addition to rupture
disks for additional protection.
Pressure relief devices and purge unit discharges must be piped to the outdoors (9.7.8). The location
must not be less than 15 ft above grade or 20 ft from a window, ventilation opening or doorway. The
line size shall be at least the discharge size of the pressure relief device or fusible plug.
Multiple relief devices can be connected to a common header. The header size must be at least the
sum of the discharge areas of the connected devices and designed to accommodate the pressure drop.
Many chiller application catalogs provide tables for sizing relief piping. ASHRAE Standard 15 also
includes tables for sizing relief piping.
Operation and Testing (Section 10)
Section 10 generally deals with field-erected refrigeration systems. For factory assembled chillers
this section should not be an issue. Where there has been field installed refrigerant piping, the test
procedures describe in section 10 must be followed.
General Requirements (Section 11)
Section 11 covers general requirements. Permanent signs are required indicating (11.2.1):
Name and address of installer
Refrigerant number and amount
Lubricant type and amount
Field test pressure
Application Guide AG 31-003-1
37
Single Chiller System
Single chiller systems are the easiest to design and operate but are also the least efficient chiller plant
design for buildings. Moreover, they provide no redundancy. If the chiller fails, all cooling is lost.
Single chiller plants require the smallest mechanical room, particularly if the chiller is air or
evaporatively cooled.
Basic Operation
Figure 35 shows a single water-cooled chiller plant with constant flow and 80% cooling load
diversity. Chilled water is circulated by the chilled water or primary pump through the chiller to the
load and back to the chiller. The chilled water loop can be either constant flow or variable flow.
Variable Flow systems increase the complexity but offer significant pump work savings. Variable
flow systems are covered in Primary/Secondary Systems and Variable Primary Flow Design. A
condenser loop is required for water cooled chillers. This includes a condenser pump, piping and a
cooling tower or closed circuit cooler. The condenser loop operates whenever the chiller operates.
Figure 35 –Basic Single Chiller System Operation
52F Chilled Water
Return
800 Ton Load
2400 Usgpm
95F
2400 Usgpm Chilled
Water Pump
67 kW
2400 Usgpm Condenser
Water Pump
33.5 kW
800 Ton Chiller
0.55 kW/ton
Cooling Tower
40 kW
85FSupply
To Chiller
44F Chilled Water
Supply
For constant flow systems,
the chilled water temperature
range varies directly with the
load. Depending on the load
diversity, the chiller design
temperature range will be
less than the range seen at
each load. In this case, the
chiller range is 8°F while the
cooling coil range is 10°F
(Refer to Piping Diversity,
page 24). The overall result
is increased chilled water
pump and pipe capital cost
plus higher annual pumping
cost.
Basic Components
Chillers
The chiller is sized to meet the design load of the building or process. For building loads, the chiller
only operates at full capacity for a few percent of the time. The balance of the time the chiller is
operating in the 50 to 60% range (depending on the building load profile). Most chillers provide their
most efficient performance at or near full load. Single chiller plant design does not promote optimal
use of the chiller’s performance. An exception to this is the McQuay Dual Compressor chiller, which
operates at its most efficient point at 50% capacity. In addition, the dual compressor chiller offers
complete redundancy of all major mechanical components, which resolves another issue with single
chiller plant design.
Water-cooled, air-cooled or evaporatively-cooled chillers can be used. Air and evaporatively cooled
chillers do not require a condenser loop including piping, cooling tower and pump.
38
Application Guide AG 31-003-1
Figure 36 - Typical Single Chiller System
Pumps
Building Load
Condenser
Water Loop
Cooling Tower
Chilled Water Pump
Chiller
Condenser
Water Pump
Chilled Water Loop
Pumps can be constant or
variable flow. Pump basics
are covered in Pumping
Basics, page 11. Both the
chilled water and condenser
pump must be sized for the
design flowrates. Whenever
the chiller operates, these
pumps will operate.
The
result is that the design chilled
water and condenser flow are
being pumped any time the
chiller plant is operating.
Cooling Towers
Water-cooled chiller will require cooling towers. Cooling towers are covered in Cooling Tower
Basics, page 15.
Single Chiller Sequence of Operation
Single chiller plants are the most straightforward to operate. Recognizing the need for chilled water is
the first goal. This can be as simple as manually enabling the chiller. The process can be automated
with a building automation system (BAS) which can recognize when mechanical cooling is required.
All chillers must have chilled water (and condenser water, if appropriate) flow before they operate.
The simplest method is to manually turn on the pumps prior to enabling the chiller. The chiller
controller, in many cases, includes a signal to operate the chilled and condenser water pumps. In this
case, the pump starters can be interlocked with the chiller control panel to start the pumps. Pumps
should shut down when not required to save energy. The BAS can also start the pumps prior to
enabling the chiller.
☺Tip: Chillers are not technically started, they are
Variable flow systems add another
enabled. The difference is subtle but important.
degree of complexity but also provide
Enabling a chiller means the chiller is allowed to
significant pump work savings.
operate if it needs to. For instance, if there is no load,
Control sequences for variable flow
the chiller will not start even though it has been enabled.
systems are covered in other sections
If you were truly starting the chiller, the compressor
of this Guide.
would start as soon as you threw the switch.
In addition to operating the pumps, it
is necessary to prove that there is flow. Pressure differential or paddle type switches can be used and
usually are connected directly to the chiller controller. Current sensing devices can also be used.
Operating a chiller without flow can result in serious damage. It is recommended that the
manufacturer’s installation instructions be followed carefully to provide proper operation and avoid
warranty conflicts.
Systems requiring a cooling tower will need to control it. Sequences for cooling towers are covered
in detail in Cooling Tower Controls, page 18. Additional information on chiller plant controls can be
found in product catalogs, as well as in installation and maintenance manuals.
Application Guide AG 31-003-1
39
Single Chiller Plant Example
Consider a model 7-story office building in Minneapolis with 375,000 ft². The air
conditioning system is floor-by-floor VAV with reheat and a single chiller plant as shown
in Figure 35.
Chiller
58%
Fans
24%
Pumps
13%
Design Performance
Chiller
33%
Fans
43%
Tower
5%
Pumps
22%
Tower
2%
Annual Energy Usage
Reviewing the design performance does not indicate how well the system will operate
annually. The annual kWh/yr usage tells a different story. Although pumps are much
smaller than the chiller, they end up using almost two-thirds the energy that the chiller
uses. This happens because the chilled water and condenser pumps must operate at
plant design flow rates any time there is a requirement for chilled water.
Although fans are not part of the chiller plant, it is important to notice that they too
consume a significant amount of power over the course of a year. In this case, more
energy is used operating the fans than the chiller. Annual energy analysis such as this
can be performed for a specific project using McQuay’s Energy Analyzer™.
40
Application Guide AG 31-003-1
Parallel Chiller System
To provide some redundancy in the HVAC design, most designers will require two or more chillers.
Multiple chillers also offer the opportunity to improve on overall system part load performance and
reduce energy consumption. Parallel chiller plants are straightforward to design and are easily
modified for variable primary flow.
Basic Operation
Figure 37 shows a parallel water-cooled chiller plant. Chilled water is circulated by the chilled water
or primary pump through both chillers to the load and back to the chillers. The chilled water loop can
be either constant flow or variable flow. Variable flow systems increase the complexity but offer
significant pump work savings. They also resolve the issue about chiller sequencing that occurs with
parallel chillers, constant flow. (See Variable Primary Flow Design, page 75.) Variable flow systems
are covered in Primary/Secondary Systems and Variable Primary Flow Design. A condenser loop is
required for water-cooled chillers. This includes a condenser pump, piping and a cooling tower or
closed circuit cooler. The condenser loop operates whenever the chillers operate.
Figure 37 – Basic Parallel Chiller System Operation
800 Ton Load
52F Chilled Water
Return
2400 Usgpm Chilled
Water Pump
67 kW
2400 Usgpm
95F
Two 1200 Usgpm
Condenser Water Pumps
16.8 kW Each
Two Cooling Towers
20 kW Each
85FSupply
To Chiller
Two 400 Ton Chillers
0.55 kW/ton
44F Chilled Water
Supply
For constant flow systems, the
chilled water temperature range
varies directly with the load.
Depending on load diversity, the
chiller design temperature range
will be less than the temperature
range seen at each load. In this
case, the chiller temperature
range is 8°F while the cooling
coil range is 10°F (Refer to
Piping Diversity, page 24). The
overall result is increased
chilled water pump and pipe
capital cost plus higher annual
pumping cost.
Basic Components
Chillers
In most cases, the sum of the
chiller capacities meets the
☺Tip: Parallel chillers experience the same percent load.
design for the building or
For example, consider a chiller plant with a 100-ton and a
process. Additional capacity
1000-ton chiller operating at 50% capacity. With both
can be added, if required, by
chillers operating, both chillers will operate at 50% capacity.
oversizing the chillers.
It is
The 100-ton chiller will be at 50 tons and the 1000-ton chiller
common for parallel chillers to
will be at 500 tons. This occurs as long as the flows don’t
be the same size and type
change (i.e,. variable primary flow) and both chillers see the
although this not a requirement.
same return water temperature.
Water-cooled, air-cooled or
evaporatively-cooled chillers can be used. Air and evaporatively-cooled chillers do not require a
condenser loop including piping, cooling tower and pump.
Application Guide AG 31-003-1
41
Pumps
Pumps can be constant or variable flow. Pump basics are covered in Pumping Basics, page 11. The
chilled water pump is sized for the design flowrate. Figure 38 shows one main chilled water pump
providing flow to both chillers. An alternative method is to have two smaller pumps serving
dedicated chillers. Figure 38 also shows dedicated condenser pumps and cooling towers for each
chiller. The pumps and piping are sized for the design condenser flow for each chiller. Whenever the
chiller operates, the condenser pump operates.
Figure 38 - Typical Parallel Chiller System
Cooling Towers
Building Load
Chilled Water Pump
Water-cooled chillers will
require cooling towers.
Figure 38 shows dedicated
cooling towers for each
chiller. A common cooling
tower is also possible but
not common for parallel
chillers. Cooling towers are
covered in Cooling Tower
Basics, page 15.
Condenser
Water Loop
Cooling Tower
Chiller 1
Chiller 2
Condenser
Water Pump
Chilled Water Loop
Parallel Chiller Sequence of Operation
Parallel chiller plants create a unique situation when used in a constant flow system. Consider the
system operating at 50%. From a chiller performance aspect, turning off one chiller and operating the
other at full capacity is desirable. However, this will not happen. At 50% capacity, the return water
will be 49°F. The chiller that is turned off will let the water pass through it unchanged. The operating
chiller will only see a 50% load (49°F return water), and will cool the water down to the set point of
44°F. The two chilled water streams will then mix to 46.5°F supply temperature.
If the system is operated in this manner, the warmer chilled water will cause the control valves to open
(increase flow) to meet the space requirements. An iterative process will occur and the system may
stabilize. The issue is whether the cooling coils can meet the local loads with the higher chilled water
temperature. Depending on the actual design conditions, the building sensible load could be met but
high chilled water temperature will make it difficult to meet the latent load. Since this scenario is
likely to occur during intermediate weather, dehumidification may not be an issue. In areas where
humidity is an issue, this arrangement can result in high humidity within the space.
One solution is to operate both chillers all the time. This works and is a simple solution, however, it
is not energy efficient and causes unnecessary equipment wear.
Another possibility is to lower the operating chiller’s set point to offset the mixed water temperature.
This also works but has some difficulties. Lowering the chilled water setpoint requires the chiller to
work harder, lowering its efficiency. In extreme conditions, it can cause chiller stability issues.
Adding isolation valves to stop flow through a chiller when it is not operating is not recommended for
a constant flow system. It is unlikely that the pump will be able to provide design flow if all the
chilled water is directed through just one chiller. The pump will ride its curve and a loss of flow will
occur. Without design flow, it is unlikely that all the individual loads will receive their required flows.
In the event the pump could actually provide the flow through one chiller, the maximum allowable
flow rate for the chiller may be exceeded resulting in serious damage to the chiller.
42
Application Guide AG 31-003-1
The safe answer is to operate both chillers all the time chilled water is required, however, this is as
expensive as operating a single chiller plant. Staging on the pumps and cooling towers is similar to
that outlined for single chillers. Refer to Single Chiller Sequence of Operation, page 39.
Parallel Chiller Plant Example
Consider the same model building used in the Single Chiller example. The parallel
chiller plant is shown in Figure 37.
Chiller
58%
Fans
24%
Pumps
13%
Design Performance
Chiller
33%
Fans
43%
Tower
5%
Pumps
22%
Tower
2%
Annual Energy Usage
The design load performance is identical to the single chiller plant. There are small
changes in real applications when two chillers are used instead of one. For instance,
pump and chiller selections are not likely to offer identical performance, other than
being half the size.
What is more interesting is the annual energy usage is the same for both single and
parallel chillers. This occurs because both chillers were operated to provide 44°F
supply chilled water at any plant load. With both chillers operating, all the pumps and
towers had to operate as well. There was no opportunity to use only one chiller at light
loads, shut down one tower and condenser pump and shift the single chiller further up
its performance curve.
This could be accomplished by switching to variable primary flow, which would allow a
chiller to be isolated at light loads, as well as to reduce the chilled water pump size and
to lower its operating cost. This is covered in detail in Variable Primary Flow Design,
page 50.
Application Guide AG 31-003-1
43
Series Chillers
Series chillers are another method of operating more than one chiller in a plant. This design concept
resolves the mixed flow issues found in parallel chiller designs. The chillers can be preferentially
loaded as well, allowing the designer to optimize chiller performance. Series chiller systems are
straightforward to design and operate.
Basic Operation
Figure 39 shows two chillers in series. All the system flow goes through both chillers. As a result, the
water pressure drops through the evaporators are additive. The chilled water loop can be either
constant or variable flow. Variable flow systems increase the complexity but offer significant pump
savings. Variable flow systems are covered in Primary/Secondary Systems and Variable Primary
Flow Design. A condenser loop is required for water cooled chillers. This includes a condenser
pump, piping and a cooling tower or closed circuit cooler. The condenser loop operates whenever the
chillers operate.
If both chillers are the same and the condensers are piped in parallel, the lead chiller will accomplish
about 45% of the system load and the lag chiller will accomplish about 55% of the system load. This
occurs because the lead (downstream) chiller is supplying chiller water at the system set point
(typically 44°F). The lag (upstream) chiller is supplying chilled water at approximately 48.5°F to the
lead chiller. The reduced lift for the lag chiller allows it to provide more cooling capacity.
Figure 39 – Basic Series Chiller System Operation
For constant flow systems,
the chilled water temperature
range varies directly with the
load. Depending on the load
diversity, the chiller design
temperature range will be less
than the range seen at each
load. In this case, the chiller
range is 8°F while the cooling
coil range is 10°F (Refer to
Piping Diversity, page 24).
The overall result is an
increased chilled water pump
and pipe capital cost plus
higher annual pumping cost.
800 Ton Load
52F Chilled Water
Return
2400 Usgpm
95F
Two Cooling Towers
20 kW Each
Two 1200 Usgpm
Condenser Water Pumps
16.8 kW Each
2400 Usgpm Chilled
Water Pump
67 kW
Two Nominal 400 Ton Chillers.
Lag 1 Produces 440 Tons
Lead 2 Produces 360 Tons
Lag Chiller
Lead Chiller
85FSupply
To Chiller
44F Chilled Water
Supply
A problem with series chillers
is the high flow rate and the low temperature range through the chillers. The high flow rate can result
in high water pressure drops. Since the chillers are in series, the pressure drops of the chillers must be
added. If the typical 10°F system temperature difference is maintained, then single pass evaporators
should be considered. This will lower the pressure drop to an acceptable level.
Basic Components
Chillers
Chillers selected for series applications require special consideration. Special care should be taken
when using smaller chillers with limited shell arrangements such as small air or water-cooled chillers.
The pressure drops are typically designed to be acceptable with the flow rates around 2.4 gpm/ton.
When the flow is increased to 4.8 gpm/ton as in series applications, the pressure drop rises
significantly. A 10 ft. pressure drop at 2.4 gpm/ton will be a 40 ft pressure drop at 4.8 gpm/ton. With
larger chillers that offer flexible shell arrangements, single pass shells can be used to lower the
44
Application Guide AG 31-003-1
pressure drop. Two single pass shells in series will be comparable to a typical two-pass shell in water
pressure drop.
The chillers will not see
☺Tip: For series chillers, the evaporator pressure prods must be
the same duty; the lead
added. Care should be taken when using chillers with limited shell
chiller has a different lift
arrangements such as small air or water-cooled products. The
requirement than the lag
pressure drops (at the correct flow rate) can be very high. For
chiller. The more difficult
larger chillers with flexible shell arrangements, consider single
duty is the lead chiller.
pass to reduce the water pressure drops.
The selections must be
done so that the chillers operating at the specific conditions will provide the required capacity. The
actual chiller output and performance will most likely be different. Selecting both chillers to be the
same machine and able to meet the requirements of the lead position allows the chillers to be
interchangeable when the plant load is less than one chiller’s capacity. There is some performance
loss when the chiller is operated in the lag position because the chiller is not optimized for that
specific lift. It is possible to select two different chillers, each optimized for their operating
conditions. This arrangement will be slightly (about 2%) more efficient but the chillers will not be
interchangeable.
Increasing the chilled water temperature range affects series chillers differently than parallel chillers.
As the range is increased,
series chillers will generally
☺Tip: Series chillers operate more effectively at increased chilled
outperform parallel chiller
water temperature ranges than parallel chillers. As the chilled
arrangement. This occurs
water range is increased, you can expect series chiller
because the cascading effect
arrangements to outperform parallel chiller arrangements.
of series chillers enhances
the chillers’ performance.
Pumps
Pumps can be constant or variable flow. Pump basics are covered in Pumping Basics, page 11. The
chilled water pump is sized for the design flow rate. The chilled water design head will be impacted
by having to add the chiller pressure drops together. Figure 40 shows one main chilled water pump
providing flow through both chillers. Figure 40 also shows dedicated condenser pumps and cooling
towers for each chiller in a parallel arrangement. The pumps and piping are sized for the design
condenser flow for each chiller. Whenever the chiller operates, the condenser pump operates.
Figure 40 - Typical Series Chiller System
Building Load
Cooling Towers
Water cooled chillers will require
cooling towers. Figure 40 shows
dedicated cooling towers for each
chiller. A common cooling tower is
also possible but not common for
series chillers. Cooling towers are
covered in Cooling Tower Basics,
page 15.
Condenser
Water Loop
Chilled Water Pump
Cooling Tower
Lag Chiller
Lead Chiller
Condenser
Water Pump
Application Guide AG 31-003-1
Chilled Water Loop
45
Series Chillers Sequence of Operation
Series chillers can preferentially load chillers. As the chiller plant load increases, the lead
(downstream) chiller will load from 0 to 100% capacity to meet it. Once the lead chiller is loaded
(which is likely to be about 45% of plant capacity) the lag chiller is started. Here are three ways to
operate the lag chiller:
1.
Set the upstream chiller chilled water setpoint to bring on the chiller once the downstream chiller
is fully loaded. This will preferentially load the downstream chiller. The downstream chiller will
operate at full load while the upstream chiller will ramp up as the chiller plant load goes from
about 45% to 100%. If the downstream chiller is offline for any reason, the upstream chiller will
not be able to assume its role unless the chilled water setpoint is changed, either manually or
remotely.
2.
Move the upstream chiller sensor downstream of both chillers. This will preferentially load the
upstream chiller. Once the upstream chiller cannot maintain the chilled water supply
temperature, the downstream chiller will start and provide the balance of the load.
3.
Modern chiller controllers such as McQuay’s Microtech™ controllers can allow two chillers to
communicate. In this arrangement. Either chiller can be the first chiller on (assuming they were
both selected to do the lead chiller duty). Once the first chiller is fully loaded, the second chiller
will start and the load will be evenly balanced between the two chillers. This can result in about
a 2% improvement in annual chiller energy usage. Where possible, this method is recommended.
Staging on the pumps and cooling towers is similar to that outlined for single chillers. Refer to Single
Chiller Sequence of Operation, page 39.
Series Chiller Plant Example
Consider the same model building used in the single chiller example. The series chiller
plant is shown in Figure 39.
Chiller
58%
Chiller
32%
Fans
44%
Fans
24%
Pumps
13%
Design Performance
Tower
5%
Tower
3%
Pumps
21%
Annual Energy Usage
The design load performance is identical to the single or parallel chiller systems. In this
case, it has been assumed that the sum of the chiller pressure drops for series chillers
equals the pressure drops through single or parallel two-pass chillers. In most cases,
the pressure drop will be higher for series systems.
As before, air system fans are the dominant HVAC load when reviewing annual energy
usage. Series chillers provide some savings over constant flow parallel and single
chiller systems. In variable primary flow systems, parallel chillers would typically slightly
outperform series chillers at ARI conditions. As the chilled water temperature range is
increased, series chillers would again out perform parallel chillers.
46
Application Guide AG 31-003-1
Series Counterflow Chillers
Series counterflow chillers are shown in Figure 41. This arrangement differs from the series chillers
system shown in Figure 39 in that the condenser flow passes through both chillers in series,
counterflow to the chilled water. Series counterflow condenser water improves the chiller
performance as explained in the Series counterflow chiller example.
Figure 41 - Series Counterflow System Design
Series counter flow chillers can be
5 to 7% more efficient than a
single chiller at design conditions
and save up to 20% of chiller
2400 Usgpm
95F
energy annually. However, the
One Cooling Tower
condenser pump is sized for the
40 kW
entire system flow (in this case
Two Nominal 400 Ton Chillers.
2400 US gpm) and this pump
85FSupply
Chiller 1 Produces 440 Tons
To Lead Chiller
Chiller 2 Produces 360 Tons
must operate whenever any chiller
2400 Usgpm Chilled
One 2400 Usgpm
89F Supply
Water Pump
operates. The result is increased
Condenser Water Pump
To Lag Chiller
67 kW
33.6 kW
pump work annually.
Series
44F Chilled Water
Supply
chillers with parallel towers may
out perform series counterflow
chillers depending on the chiller savings versus pump losses. Where series counterflow chillers can
be advantageous is in large primary/secondary chiller plant systems.
52F Chilled Water
Return
Application Guide AG 31-003-1
800 Ton Load
47
Series Counterflow Chillers vs. Series Parallel Chillers
Parallel Condensers
The lower figure shows series chillers with the condensers piped in series counterflow to
the chilled water. The arrangement enhances the chiller performance by “cascading”
the chillers. The above figure shows the lift requirements for series chillers with parallel
towers. Chiller 1 has a smaller lift because it sees the return chilled water. Chiller 2
sees a higher lift because it cools the water to 42°F. Since both chillers have the same
discharge pressure requirement (dictated by using 85°F-95°F condenser water), the
chiller lifts are different.
Series Condensers
The above figure shows the lift requirements for series counterflow chillers. Now chiller2 sees a lower lift because the discharge pressure has been reduced as a result of the
lower condenser water temperatures. The chiller lifts are almost balanced which will
always provide the best refrigeration performance.
48
Application Guide AG 31-003-1
Using VFD Chillers in Series Arrangements
A common practice in selecting chillers for series applications is to select both chillers to be the same
and meet the lead (most demanding lift) chiller duty. For centrifugal chillers, this means the
compressors are selected for the largest lift on a design day. The chiller that is then used as the lag
chiller provides too much lift and is not optimized. A solution to this is to use a centrifugal chiller
with a VFD as the upstream chiller. This has two advantages:
1.
During periods when the chiller plant load is less than 45% (about the limit for one chiller) the
VFD chiller can be used and take advantage of any condenser relief available. Considering this
is a part load situation, condenser relief should be significant.
2.
When two chillers are required, the VFD chiller can use the VFD to optimize its performance
while being used in the lower lift application.
Both chillers do not need to have VFDs. Either chiller will work in either application (lead or lag)
without a VFD.
Series Counterflow Plant Example
Consider the same model building used in the single chiller example. The series
counterflow chiller system is shown in Figure 41.
Chiller
58%
Chiller
30%
Fans
44%
Fans
24%
Pumps
13%
Tower
5%
Pumps
23%
Design Performance
Tower
3%
Annual Energy Usage
The series counterflow arrangement has improved the chiller performance as
described in the sidebar. This has resulted in an overall design condition performance
improvement.
As expected, the annual chiller work went down because of the enhanced chiller
performance. On the other hand, the large condenser pump (sized for the design
condenser flow) which must operate whenever there is a need for chilled water, has
increased the annual pump work. Whether series counterflow will save energy on an
annual basis will depend on the pump penalty vs. the chiller savings.
System Comparison
The previous section covered several common chiller system designs based on constant flow systems.
Each system has strengths and weaknesses in terms of design. A key operating parameter is the
annual energy usage.
Table 5 - Design Condition Performance In kW
Systems
Chiller
Pumps
Single Chiller
Parallel Chillers
Series Chillers
Series Counterflow Chillers
440
440
440
424
100
100
100
100
Application Guide AG 31-003-1
Cooling
Tower
AHU
Fans
Total
40
40
40
40
185
185
185
185
765
765
765
749
49
Table 5 shows the design condition power usage of the chiller systems covered in the last section. As
can be seen, all the systems have the same full load performance. The series counterflow chillers
provide better performance than the other systems because of the cascading effect. At nominal ARI
conditions, these chillers would perform the same as the other chillers.
Table 6 shows the annual energy usage of the various chiller systems. This tells quite a different
story. The single and parallel chiller plants perform the same because the parallel system operates the
two chillers at all load points. There is no easy way to shut down a chiller in a parallel, constant flow
arrangement.
Table 6 - Annual Energy Usage In kWh/yr
Systems
Chiller
Pumps
Single Chiller
Parallel Chillers
Series Chillers
Series Counterflow Chillers
258,344
258,344
237,607
227,718
175,689
175,689
160,762
173,564
Cooling
Tower
AHU
Fans
Total
16,597
16,597
19,243
19,153
334,237
334,237
334,237
334,237
784,867
784,867
751,849
754,672
The series chillers outperformed the parallel chillers. The water pressure drops, however, were held
constant. If the water pressure drops through the series chillers had been increased as is typically the
case, then there would have been little or no difference.
At design conditions, the series counterflow chillers appeared to have a distinct advantage, however,
the pump penalty on the condenser side actually increased the overall annual energy usage. Here are
some relationships that can be used:
50
Y
Design performance is a poor indicator of annual performance. There is no way to tell which
system will perform the best by reviewing the design condition performance.
Y
Sequence of operation is a major factor. How the system operates will vastly affect the savings.
Y
In constant flow systems, pumps are a major component. Although the pump motors are only
25% the size of the chiller, they use more than 60% of the power that the chiller uses.
Y
Increasing the chilled water temperature range will improve the performance of the series chiller
systems relative to other chiller systems. The chillers will operate more efficiently and the
pressure drop penalty will be less of an issue.
Y
Variable flow systems can save significant pump energy. They will be discussed in future
sections.
Application Guide AG 31-003-1
Primary/Secondary Systems
For large chillers or where more than two chillers are anticipated, primary/secondary (also called
decoupled) piping systems are often used. To reduce installation and operating costs, it is desirable to
apply diversity to system flow. With diversity applied to flow, the pumps and piping will be smaller.
To accomplish this, two-way control valves are used at the loads. At the same time it is desirable to
provide constant flow through the chillers to maintain chiller stability.
The solution is
primary/secondary piping.
Basic Operation
Figure 42 - Basic Primary/Secondary System Operation (50% Load)
51.5F Return Water
To Chiller
Two 400 Ton Chillers
Each At 300 Tons
(Balanced Load)
480 gpm Flow Through
Decoupler
Chiller 1- On
Two Primary Pumps
Each At 960 gpm
Building Load
600 Tons
(50% Load)
54F
51.5F
44F
Flow
Figure 42 shows a 1200-ton
primary secondary system
with three chillers.
The
system is operating at 50%
or 600 tons. The 600- ton
load requires 1440 gpm.
Two chillers are operating
along with their 960 gpm
primary pumps.
Chiller 2- On
The additional flow from the
two primary pumps bypasses
44F
the building through the
Variable Secondary
decoupler. The bypassed
Chiller 3- Off
Pump 1440 gpm
water mixes with the return
water from the building and
is returned to the chillers. Both chillers operate at the same percent load (300 tons).
Basic Components
Figure 43 – Typical Primary/Secondary System
Primary Pump
Typ One Per Chiller
Condenser Water Pump
Typ One Per Chiller
Building Load
2 Way Valves
Decoupler
Cooling Tower
Chilled Water Loop
Flow Varies With Load
Secondary Pump
Variable Flow
Application Guide AG 31-003-1
51
Chillers
Figure 43 shows a typical primary
☺Tip: All operating chillers in a primary-secondary
secondary chiller plant with four
plant see the same percent load. For example, consider
chillers. They can have any number of
a plant consisting of one 100-ton chiller and one 1000chillers. Any size and type of chiller
ton chiller operating at 50% load. In this case, the 100can be used.
Different capacity
ton chiller will operate at 50 tons and the 1000-ton
chillers are acceptable and can be
chiller at 500 tons. Preferentially or backloading
advantageous depending on the load
loading chillers is possible, see Decoupler.
profile. The only requirement is all
chillers must operate on the same
chilled water temperature range. Unless specially configured (See Decoupler, page 53) all operating
chillers will have the same percent load.
Primary Pumps
Primary pumps provide constant flow through the chillers. They can be dedicated to each chiller as
shown or there can be a primary pumping plant providing constant flow to each chiller. Primary
pumps can utilize a common header (See Figure 44) to allow a particular pump to serve several
chillers. The advantage is should a pump fail, the chiller can still be used by activating one of the
other pumps. A spare pump can also be built into the arrangement. The disadvantage to headered
primary pumps is complexity and cost.
If the chillers have different flow requirements (meaning they are different sizes) then intermixing
pumps becomes even more complicated. It can be done using VFDs on the pumps. The BAS can be
preprogrammed with the appropriate pump speed required to deliver the correct flow to each chiller.
This allows each chiller to receive its correct flow rate.
Figure 44 - Alternative Primary Pump Arrangement
Spare
Pump
Common Header Allows
Any Pump to Operate with
Any Chiller
Chiller Isolation
Valves
The flow for each chiller is
based on the design flow
required by the chiller. The
flow is only provided when
the chiller is operating. An
automatic isolating valve is
required for each chiller to
stop short-circuiting when
the chiller and pump are off.
Primary pumps need only
provide enough head to
move chilled water through
the chiller and the piping
pressure drops between the
chiller and the secondary
pumps. Heads in the range
of 25 to 75 ft are common.
Condenser Pumps
If the chillers are water cooled, each chiller will have a condenser pump and cooling tower or other
form of heat rejection device. Like the primary pumps, the condenser pumps can be dedicated to each
chiller as shown or a condenser water pump plant can provide condenser flow. The flow rate to each
chiller is typically constant and based on the design flow rate for the chiller. Where the head pressure
drop is particularly high, variable flow condenser pumps may offer additional savings and are
becoming more common in chiller plant design.
52
Application Guide AG 31-003-1
Cooling Towers
Cooling towers can be grouped or individual. Individual towers allow the tower to be sized
specifically for the chillers needs, which can be important in hybrid chiller plants. Refer to Cooling
Tower Basics, page 15 for more details.
Secondary Pumps
Figure 45 - Basic Secondary Loop
Secondary pumps are variable flow
and sized to provide flow throughout
the chilled water plant. In a sense,
they handle all the pressure drops
“outside the mechanical room”.
Refer to Variable Flow Pumps, page
13 on how to vary the flow through
pumps.
Two Secondary
Pumps in Parallel
for Redundancy
Most secondary pump arrangements
include multiple pumps and often a
spare pump.
Figure 46 - Multiple Secondary Loops
Building 1
100 ft of Head
Dedicated Secondary Pumps
Grouped By Common
Pump Head Requirement
Building 2
200 ft of Head
Building 3
300 ft of Head
Figure 46 shows dedicated pumps
for various loops. Multiple loops
can serve areas with different
operating schedules or widely
different fluid pressure drops
(such as a building on the far side
of a campus). The individual
loops can be scheduled off when
not required. A good system
design should always group loads
with common pressure drop and
scheduling requirements to reduce
pumping work.
Decoupler
Referring to Figure 45 it would appear that the primary and secondary pumps are in series. This is
not the case however, because of the decoupler. The decoupler allows the pumps to operate at
different flow rates. This is necessary because the primary pumps are fixed speed and the secondary
pumps are variable speed. Only on special occasions will the primary pump flow and the secondary
flow be equal. An example would be when the cooling load (and secondary flow) can be met by a
fully loaded chiller.
Application Guide AG 31-003-1
53
Figure 47 - Primary Vs. Secondary Flow
100
Primary Flow
% Flow
75
50
Secondary Flow
25
0
0
25
50
75
100
% Plant Load
Figure 47 shows primary flow vs. secondary flow.
Secondary flow is based on the load in the
building. Specifically, the secondary flow rate is
produced to maintain the necessary system
pressure differential. Primary flow must always
meet or exceed the secondary flow. Any excess
primary water flows through the decoupler to the
return side and back to the chillers. Any time the
primary flow is less than the secondary flow,
warm return water will flow “backwards” through
the decoupler and mix the primary flow going out
to the building.
Decoupler Sizing
Decouplers should be sized for the flow rate of the largest primary pump. This may be more than the
design flow rate of the largest chiller if overpumping is being considered. The pressure drop should
not exceed 1.5 ft. As the pressure drop through the decoupler increases, it tends to make the primary
and secondary pumps behave like they are in series.
Figure 48 - Decoupler Sizing
Minimum 10 pipe
Diameters From Decoupler
To First Chiller
Decoupler
3 Pipe Diameters
Minimum Length
Friction Loss < 1.5 ft.
Decoupler Location
The location of the decoupler
line will change how the
chillers are loaded. Figure 43
shows the typical layout with
the decoupler between the
chillers and the load. In this
situation, each chiller sees the
same return water temperature
even at part load conditions.
To avoid thermal contamination, the
decoupler should be at least three
pipe diameters in length. Longer
decouplers tend to increase the
pressure drop. When the secondary
return flows straight through in the
tee to the primary return, there
should be at least 10 pipe diameters
to the first chiller. This is to help
avoid the possibility of having
stratification in the primary return
line, which can lead to unmixed
water to the first chiller. This can
lead to chiller cycling.
☺Tip: In situations where a new chiller is added to an older
existing chiller plant, relocating the decoupler can take full
advantage of the new chiller’s part load performance. Older
chiller may operate at 1 kW/ton or more at full load, worse at
part load. Relocating the decoupler allows the older chillers to
be base loaded (their best operating point) while the new chiller
is operated at part load. Consider either a VFD or dual
compressor chiller for additional savings.
Figure 49 shows the decoupler line in a different location. Locating the chillers between the
secondary loop and the decoupler line causes the return water temperature to each chiller to vary.
This is often referred to as “backloading” or “preferentially” loading the chillers. Chiller 2 in Figure
49 will see close to the secondary loop return water temperature. Chiller 1 will see a mixture of
supply water and return water. As a result Chiller 2 is more heavily loaded than Chiller 1.
54
Application Guide AG 31-003-1
Figure 49 - Backloaded Primary Loop Layout
Relocating the decoupler can make
sense if one or more of the chillers
is a dual compressor model. The
CH-2 (Nom 400 Tons)
dual compressor chiller has very
Is At 100% Capacity
good part load performance. Single
compressor chillers typically work
Chiller 3- Off
54F
Secondary Pump
best when fully loaded. By locating
1440 gpm
54F
the dual compressor chiller close to
the decoupler line and the single
Two Primary Pumps
Chiller 2- On
Each At 960 gpm
CH-1 (Nom 400 Tons)
compressor chiller furthest away,
Is At 50% Capacity
49F
44F
the strengths of each chiller can be
maximized. Another application
44F
Chiller 1- On
480 gpm Flow Through
Flow
Decoupler
for backloading chillers is where
one of the chillers is a heat recovery
type or a McQuay Templifier™ is connected to the condenser loop. In this case, providing additional
load to that chiller provides a heat source for the energy recovery process.
54F
Building Load
600 Tons
(50% Load)
Decouplers should be sized for the maximum design chilled water flow through the largest chiller.
Their length should be as short as possible to minimize pressure drop.
Backloaded Chiller Example
The table below shows the chiller plant performance for Figure 42 and Figure 49. Assume
for Figure 42 the two chillers are standard 400-ton single compressor type. In Figure 49,
Chiller 1 is a standard chiller while Chiller 2 is a dual compressor chiller with outstanding part
load efficiency. By base loading the single compressor chiller and taking advantage of the
dual chiller’s part load performance, the power input can be cut by up to 10 percent.
Chiller Plant Performance vs. Decoupler Location
Application Guide AG 31-003-1
Figure 45
CH-1
CH-2
Total
Cap. (tons)
300
300
600
RWT (°°F)
51.5
51.5
51.5
SWT (°°F)
44
44
44
Power (kw)
124.6
124.6
249.2
Figure 52
CH-1
CH-2
Total
200
400
600
49
54
44
44
44
73.2
151.7
224.9
55
Tertiary Pumping
Figure 50 - Tertiary Pumping
Tertiary Pump To Boost
Pressure For Specific Load
Chilled Water
Supply Line
2 Way Control Valve Maintains
Tertiary Loop At A Temperature
Above System Temperature
There are two key applications
where tertiary piping is helpful.
The first is where the pressure
available in the secondary loop
is not sufficient for a specific
load. The second is where a
load requires a different
temperature range than the
main system.
Figure 50 shows two piping
methods for tertiary piping.
The method on the left can be
used to assist where the
pressure drop for a specific
load is greater than the pressure differential available in the main secondary loop. This often happens
when a new load is added to an existing loop. An additional tertiary pump is added to provide
additional pressure to overcome the specific load.
Chilled Water
Return Line
The arrangement on the right of
☺Tip: There are many instances where facilities designed
Figure 50 includes a tertiary pump,
with different chilled water temperature ranges are
common pipe and a two-way control
required to operate from a common chilled water plant.
valve. The tertiary pump provides
This is a common occurrence for large university and
the necessary flow and head for the
health care campuses. Tertiary piping can be used to
facility it serves. If the two-way
connect buildings with different design temperature ranges
valve is closed, the chilled water
and supply water temperatures to a common plant.
recirculates in the facility through the
common pipe. As the two-way valve
is opened, warm water is returned to the return header while cool chilled water is introduced.
This arrangement can be variable flow by making the tertiary pump variable. A key advantage of this
arrangement is the tertiary loop does not have to have the same temperature range as the main loop.
The design chilled water temperature in the tertiary loop must be warmer than the main supply chilled
water temperature. If they are the same temperature, the two-way valve will open and bleed supply
water into the return line leading to low delta T syndrome (See Low Delta T Syndrome Causes and
Solutions, page 82). The two-way valve should control to maintain the tertiary loop supply
temperature (approximately 2°F warmer than the main loop) and should close when the tertiary loop
is not in operation to avoid unnecessary crossflow.
System Expansion
Figure 51 - Expanding the System
New Chiller Can Be Added
To Existing System
New Chiller
Existing Chiller
Primary/secondary piping allows easy
expansion both in the chiller plant (primary
loop) and the building (secondary loop).
To expand the chiller plant capacity,
another chiller can be added to the loop as
shown in Figure 51. By strategically
locating the decoupler and the new chiller
(see Figure 49), it is possible to apply a
greater load on the new chiller. This can be
advantageous if the new chiller is more
efficient than the rest of the plant.
Existing Chiller
56
Application Guide AG 31-003-1
If the building load is increased, a new loop can be added. The pump for the new loop can be sized to
meet the new loop’s pressure drop requirements.
Varying Chiller Sizes
One advantage of primary/secondary systems is varying the chiller sizes. As long as the supply water
temperature and the design delta T are the same, the chillers can have different capacities.
Varying the chiller sizes allows chillers to be selected so the chiller plant is at maximum performance
when the run-hours are highest. For example, consider a chiller plant where two chillers can be used.
The bulk of the run-hours
will be at 50% to 70% of
☺Tip: Healthcare facilities using constant volume with reheat
design capacity. This will
systems have a significant base load. The only variable load is
require the two equally sized
the ventilation load. This makes health care facilities an excellent
chillers to operate between
choice for varying chiller sizes.
50% and 70% of their
design capacity. By varying the chiller sizes to one at 700 tons and one at 300 tons, the system load
can be met with one chiller for the bulk of the operating time. The savings come from operating one
chiller at near full load conditions over two chillers at part load conditions and from avoiding
operating additional ancillary devices such as primary and condenser pumps.
Variable Chiller Size Example
Consider a 320,000-square foot hospital in Minneapolis. The design load is 1000 tons.
The primary system is a two chiller primary/secondary system. The graph below compares
two 500-ton chillers, a 700-ton dual compressor chiller with a 300-ton chiller and a 700-ton
VFD chiller with a 300-ton chiller.
900000
800000
700000
kWh
600000
500000
400000
300000
200000
100000
0
Chillers
2-500 ton
Pumps
1-700 ton Dual, 1-300 ton Single
Towers
1-700 ton VFD, 1-300 ton Single
The two 500-ton chillers provide a benchmark. Since the hospital has a load profile with
many hours between 50 and 70% of design capacity, the next two options outperform the
benchmark. During these hours, only one chiller is required to meet the load avoiding the
need for two primary and condenser pumps. The result is more efficient use of the chiller
and reduced pump work.
To take full advantage of the situation, the larger chillers are either dual compressor type or
VFD type, both of which have excellent part load performance. Even if one of the
benchmark chillers were switched to a VFD chiller, the two options would still have had
better performance.
Application Guide AG 31-003-1
57
During the spring and fall seasons, the operator has the option of using the chiller whose size best fits
the expected load. For instance, on a light load day, the smaller chiller can be used. The chiller will
be more fully loaded than the larger chiller offering a performance improvement for the chiller. In
addition, the smaller primary condenser pump and tower fan will be used offering ancillary equipment
savings.
Very Large Chiller Plants
Very large chilled water plants follow the same basic design considerations discussed so far. The scale
of large chiller plants, however, creates some trends that should be addressed. Large plants tend to
use large (18°F or greater) chilled water ranges to reduce pump and piping sizes and pump work.
This in turn requires lower chilled water temperatures to offset the effect on the cooling coils (see
Water Temperatures and Ranges, page 25).
Figure 52 - Series Counterflow Chillers in P/S Arrangement
Figure 52 shows series counterflow chillers in a primary
/secondary system. The series
counterflow arrangement provides an efficient means to
produce 40°F supply water with
and 18°F temperature range. The
series counterflow arrangement
can provide about 5% better
annual performance than single
large chillers when using large
temperature ranges.
The primary/secondary arrangement provides variable flow in the secondary loop to reduce pipe and
pump size and save pump work.
Primary/Secondary Sequence of Operation
Primary/secondary chiller plant operation can become very complex. It is not unusual to have
dedicated and specialized building automation systems to operate the chillers and the ancillary
equipment. While a complete discussion on the many ways of operating a complex plant is beyond
the intention of this Guide, here are a few key areas to consider:
Condenser Pump and Cooling Tower Operation
Whenever a chiller is on line, there will need to be condenser flow and a means to cool it. With
dedicated pumps and towers to each chiller, this is straightforward. They can be operated by either
the chiller control panel, assuming it has outputs, or by the BAS. The chiller control panel may offer
better performance since it has intimate understanding of the needs of the chiller. Using the BAS to
operate the equipment makes the operation easily visible to the control system and to the operator.
(For example, without an additional flow sensor, it may not be obvious to the BAS that the condenser
pump is operating.) Using either Open Protocol™ or Protocol Selectablity™ allows the chiller to
operate the equipment while providing easy visibility for the BAS and operator. The information is
passed digitally from the chiller controller to the BAS.
When the condenser pumps are shared in a common header the sequence becomes more complex.
Automatic isolation valves will be required. If the pumps are all the same size, the BAS must open
the valve and start a condenser pump. The pump sequence is usually based on pump run-hours.
58
Application Guide AG 31-003-1
When the chillers have different condenser flow requirements, the system becomes very complex.
Flow meters may be required.
When a common cooling tower plant is used, a sequence to determine the optimum condenser water
temperature is required. Special care should be taken when an absorption chiller is used in a hybrid
plant. Generally an absorption chiller has different condenser water requirements than a centrifugal
chiller.
Primary Pump Operation
Primary pumps will have similar issues as condenser pumps. Dedicated pumps are straightforward.
Common pumps in a headered arrangement are more complex. When overpumping is considered as a
solution to low delta T syndrome or to take advantage on additional chiller capacity during low lift
situations, the sequence can be very complex.
Secondary Pump Operation
Secondary pump operation in general is covered in Variable Flow Pumps, page 13.
Chiller Staging
A critical requirement of primary /secondary systems is that the primary flow always be equal to or
exceed the secondary flow. Theoretically this should happen because the chilled water temperature
range is constant and the chilled water flow is proportional to the cooling load.
Assuming this happens,
☺Tip: It is absolutely necessary for the primary chilled water flow
chillers could be staged on
to equal or exceed the secondary flow (See Low Delta T Example,
and off based on their
page 83). The primary/secondary control system must maintain
load. However, this is not
this flow relationship above all.
necessarily a good control
scheme. First, Low Delta
T syndrome can cause a disconnect so the chilled water flow is not proportional to load. (See Low
Delta T Example, page 80). Just using chiller load will not recognize when this situation occurs. A
second issue is the chiller power draw is not an exact indicator of the actual cooling effect. For
instance, if there is condenser water relief, the chiller will produce the required cooling effect with
less kilowatts. It is even possible for the chiller to produce more than the design cooling capacity
with the same kilowatts if there is some form of condenser relief.
Monitoring the chiller power load can be advantageous and can provide some guidance in chiller
staging along with other data inputs discussed below. Power monitoring can be accomplished by
using communication gateways such as Open Protocol™ or Protocol Selectablity or with power
meters.
To make sure the primary flow meets or exceeds the secondary flow, the BAS must also monitor
chilled water flows. One method is measuring the direction of flow through the decoupler. A flow
meter in the decoupler can be difficult due to the short pipe length and low flowrates. It is important
that if a flow meter is used, that it actually works and provides meaningful information.
Another method is to measure the chilled water temperature in the decoupler. A single temperature
sensor in the decoupler in principle should work. For instance if the temperature is near the supply
water temperature setpoint, then flow must be going from the supply to the return (which is what is
required). However, if the temperature rises to close to the return water temperature, then the flow
must have reversed (which is not desirable). In practice, a single sensor can lead to false readings for
several reasons. For example, low delta T syndrome can make the actual chilled water temperature
range very small so the BAS cannot tell which way the water is flowing.
A more reliable method is to use temperature sensors in the supply and return piping on both sides of
the decoupler. This arrangement allows the BAS to monitor the actual chilled water temperature
range at the decoupler. With four sensors, the BAS can monitor that the chilled water temperature
Application Guide AG 31-003-1
59
does not rise as it passes the decoupler, that the return water temperature may rise as it passes the
decoupler and that the decoupler water temperature is close to the supply chilled water temperature.
Once the situation occurs where there is reverse flow in the decoupler, another chiller and primary
pump must be added to keep the chilled water plant operating properly. Using temperature sensors
may not provide very much warning.
Another method for staging chillers is to use a flow meter in the chilled water supply line down
stream of the decoupler. Using the required flow and the flowrates for each of the primary pumps
(These are fixed flowrates), the BAS can monitor that there is enough primary flow for the required
secondary flow. This method is very reliable. It can also provide some warning that another
chiller/primary pump is going to be required. Normal schedules have the next chiller start when the
current chiller has been operating at 90% capacity for 30 minutes. The actual load and time period
vary from project to project. Many operators do not want a chiller to automatically start but prefer
that the BAS indicate a chiller is required. If the operator acknowledges the start request, the BAS
can then enable another chiller.
Optimizing High Part load Performance Chillers
High part load performance chillers such as a VFD or dual compressor chiller may create an
opportunity to operate the chiller plant in a different but more efficient manner. These chillers operate
more efficiently at part load then at full load. Refer to Dual Compressor and VFD Chillers, page 31.
State of the Art Chiller Plant Operation
The previous section provides the basics to get a primary/secondary system to operate satisfactorily.
Leading edge control systems are aimed at improving overall system efficiency. To accomplish this,
algorithms are developed that model the building load profile and monitor the weather. Threedimensional chiller models are also used along with matrices for the power consumption of individual
ancillary components. The program then simulates the building load and monitors the weather
conditions. It evaluates which combination of equipment will use the least power to accomplish the
load. In large systems, this additional effort has been shown to pay for itself.
60
Application Guide AG 31-003-1
Water-Side Free Cooling
Some HVAC systems (fancoils) can require chilled water year round. Where the weather allows,
waterside free cooling can avoid the need for mechanical cooling. Other systems such as floor-byfloor compartment systems can use waterside free cooling and avoid the need for access to an exterior
wall.
Direct Waterside Free Cooling
Figure 53 - Direct Water-side Free Cooling
There are several ways to provide
waterside free cooling. The chilled
water loop can be connected by means
of three-way valves, directly to the
cooling tower in a “strainer cycle”
method. This method is not preferred
because the chilled water loop is then
exposed to atmosphere introducing dirt
and
creating
water
treatment
difficulties.
Parallel Waterside Free Cooling
Figure 54 shows a heat exchanger in parallel with the chiller. During free cooling the chiller is off
and isolated by valves. The heat exchanger rejects heat into the condenser water loop. For this to
happen, the condenser loop must be colder than the chilled water loop (the reverse of chiller
operation).
Figure 54, Waterside Free Cooling With Heat Exchanger In Parallel
This system is “non-integrated”
meaning it can only be either
mechanical cooling or free cooling.
Nonintegrated systems generally do
not offer as much savings as
integrated systems but avoid
additional operating hours for
chillers at light loads. Continuous
light load operation for some
chillers can lead to operational
difficulties such as oil migration or
repeated starts.
Application Guide AG 31-003-1
61
Series Waterside Free Cooling
Figure 55, Free Cooling in Series with Chillers
Figure 55 shows a different free cooling
arrangement with the chiller in series with
the heat exchanger.
Since the heat
exchanger operates with a higher return
chilled water temperature, the operating
season is longer than the parallel
arrangement, offering more annual savings.
This is an integrated system with the chiller
“trimming” the chilled water temperature
while operating with significant condenser
water relief. Because the heat exchanger is
piped directly in series with the chiller, the
heat exchanger pressure drop must be overcome whenever the chiller plant operates. ASHRAE
Standard 90.1-2001 requires that the pressure drop by 15 ft or less.
Figure 56 – Free Cooling with Tertiary Loop
Figure 56 shows a modified version
where the heat exchanger uses a small
tertiary loop and a dedicated pump.
This arrangement removes the heat
exchanger pressure drop from the main
chilled water system.
Locating the heat exchanger in the main
return line allows the heat exchanger to
use all the return chilled water flow for
all the chillers as a heat source as
opposed to just the flow for a single
chiller.
62
Application Guide AG 31-003-1
Waterside Free Cooling Design Approach
Designing a waterside economizer system requires knowledge of how the building will operate at part
load. Variable chilled water flow systems are a better choice than constant flow because they
maintain a higher return water temperature, which provides hotter return water temperature for the
heat exchanger. The following is one method for designing the system.
Y
Calculate the building load at the ambient conditions where free cooling can support the building
(changeover point). 50°F db and 45°F wb, this is a common design point since it is the ASHRAE
90.1-2001 requirement.
Y
Establish the chilled water supply temperature required by the cooling coils to meet the load at
the changeover point. Concentrate on systems serving core load areas. Generally, the only relief
these zones see is in the drop in enthalpy of the ventilation air. The goal here is to “trade” the
coil capacity used for cooling ventilation air in the summer for a higher supply water temperature.
Y
Establish the return water temperature. The return water temperature is required to size the heat
exchanger. The conservative solution is to re-rate all the cooling coils with the raised supply
water temperature and the reduced cooling loads. Then take weighted average to obtain the
return water temperature. A simpler calculation for variable flow systems is to assume the chilled
water range will remain the same and the flow will be proportional to the building load at the
crossover point. For constant flow systems, the flow will be the same and the chilled water
temperature range will be proportional to the load.
Y
Select a heat exchanger. The design requirements will depend on which type of arrangement is
selected. With a heat exchanger on a tertiary loop as an example (Figure 56), use the following:
Y
Y
The chilled water flow rate at the crossover point.
Y
The chilled water return temperature at the crossover point.
Y
The condenser water design flow rate.
Y
Assume a 2 to 3°F approach for the heat exchanger.
Y
Solve for the entering and leaving condenser water temperature.
Confirm the cooling tower can meet the design requirements at a wetbulb of 45°F.
Cooling Tower Sizing
Cooling tower sizing is critical for effective operation during free cooling. Normally, the cooling
tower is sized to reject the heat collected in the building plus the compressor work at design
conditions. Industry standard conditions are 95°F entering water, 85°F leaving water and 3.0 US gpm
with an ambient wetbulb of 78°F.
Figure 57 shows a typical cooling tower performance at industry standard (Cooling Tower Institute or
CTI) conditions for different temperature ranges. Following the 10°F range line down to 45°F
wetbulb shows the best water temperature available will be 61°F. Add to this a 2°F approach for the
heat exchanger and the HVAC system would need to be able to cool the building with 63°F supply
chilled water. Once the chiller compressors are removed from the cooling tower load, the new
condenser temperature range becomes approximately 8°F. Assuming the cooling load is only 50% by
the time the ambient wetbulb has dropped to 45°F, then the temperature range now becomes 4°F.
Reviewing Figure 57 for a 4°F range shows the condenser supply water temperature can now be 53°F
providing 55°F chilled water. This is still very warm and it will be difficult to properly cool the
building.
Application Guide AG 31-003-1
63
Figure 57 - Cooling Tower Performance Curve at Standard Conditions
Cold Water Temperature (°F)
90
10°F Range
80
8°F Range
70
4°F Range
60
Typical Cold Water For
Process Load And Off-Season
Air Conditioning (Arbitrarily
Selected)
50
40
30
35
40
45
50
55
60
65
70
75
80
Wet-Bulb Temperature (°F)
Cold Water Temperature (°F)
Figure 58 - Cooling Tower Performance Optimized For Free Cooling
Figure 58 shows a cooling tower
optimized for free cooling.
The
90
cooling tower was selected to provide
80
48°F condenser water at a 45°F
10°F Range
wetbulb and 4°F range (50% building
70
load). This allows 50°F chilled water
8°F Range
to be produced.
60
4°F Range
50
40
30
30
35
40
45
50
55
60
65
70
Wet-Bulb Temperature (°F)
75
80
At summer design load conditions, the
optimized cooling tower can produce
81°F at a 10°F range. Reducing the
condenser water temperature 4°F can
significantly reduce the cost of the
chiller and improve the performance.
In most cases the saving will be
enough to cover the cost of the larger
cooling tower.
Waterside Free Cooling Sequence of Operation
The actual details of the control sequence will depend on which system is selected. There are several
parameters, which all the systems have in common. Until the condenser water is colder than the
chilled water, there can be no free cooling. During periods when free cooling is not possible, all
parasitic energy loses should be minimized. Where possible, remove the heat exchanger from the
system pressure drop by means of valves. Shut down any pumps associated with just the heat
exchanger.
The cooling tower controls must strive to lower the condenser water temperature as much as possible.
Condenser water much colder than about 65°F is too cold for a chiller. Any kind of integrated system
must involve some sort of head pressure control such as a three-way bypass valve around the chiller.
Once the cooling tower can no longer provide condenser water cold enough to perform any free
cooling, the cooling tower control logic should change to optimize the chiller performance rather than
the heat exchanger.
64
Application Guide AG 31-003-1
Many buildings go into night setback during unoccupied hours. When the building returns to
occupied operating mode, the chiller plant can attempt to use free cooling. If non-integrated free
cooling cannot meet the load, then mechanical cooling will be required.
A key issue is the transition from free cooling to mechanical cooling. Once the building load cannot
be met by free cooling, the chiller will need to be started. At that point, the condenser loop will be
cooler than the chilled water loop, which is “backwards” from the chiller point of view. To allow the
chiller to operate, a cooling tower bypass line and valve is required. The modulating bypass valve
around the chiller will allow the chiller to raise the condenser loop temperature quickly and minimize
the condenser water volume (thermal mass). Most chillers can control the three-way valve directly.
Alternatively, the BAS can modulate the valve to reach a minimum of about 65°F as quickly as
possible.
An issue with modulating the
☺Tip: The transition from free cooling to mechanical
condenser flow through the chiller
cooling requires raising the condenser water temperature
is the condenser flow switch will
to about 65°F as quickly as possible. The best method is
not “see” flow and this will shut
to use a modulating three way valve around the chiller and
down the chiller on a safety. One
have the heat from the chiller raise the condenser water
method to resolve this is to wire a
temperature as quickly as possible.
refrigerant head pressure switch in
parallel with the condenser flow switch. Below the minimum acceptable head pressure, the switch
should “make” or close. Above the minimum head pressure, the switch should “break” or open. The
result will be at low head pressure the head pressure switch will be closed and the flow switch will be
overridden. Once there is enough head pressure, the head pressure switch will open and the flow
switch can monitor the flow.
While in free cooling mode, colder chilled water can produce colder supply air. In VAV systems this
can lower the supply air volumes and save fan work. For constant volume systems, colder air is of no
value and the minimum chilled water temperature should be the summer design supply water
temperature. Once this temperature is reached, the cooling tower fans should modulate to maintain
the chilled water temperature and save tower fan energy.
Maintaining the condenser water temperature above freezing conditions is also important. The
cooling tower fans should be staged off to maintain the condenser water temperature at 35°F
minimum.
Economizers and Energy Efficiency
The goal of either air or waterside economizers is to reduce energy usage. Economizer energy
analysis requires annual energy analysis. Airside economizers should be used where possible since in
all but the driest climates, airside economizers are more efficient than waterside economizers. An
exception to this is where high levels of humidification are required since humidification is expensive
and introducing large amounts of outdoor air for cooling would add to the humidification load.
ASHRAE Standard 90.1-2001 requires the following for economizers:
Y Each cooling system with a fan requires either air or waterside economizers. There are many
exceptions (6.3.1). Table 6.3.1 in Standard 90.1 lists the minimum system size for which an
economizer is required. The table is based on ambient wetbulb and drybulb conditions plus the
hours of operation. Weather data is provided in an appendix.
Y One exception is the use of condenser heat recovery for service water heating .(6.3.1.d)
Y Waterside economizers must be able to meet the entire building load at 50°F db and 45°F wb and
below. (6.3.1.2.1) There is an exception where dehumidification requirements cannot be met.
Y Precooling coils and heat exchangers in line with the chilled water loop cannot exceed 15 ft.
water pressure drop. (6.3.1.2.2)
Y Economizers must be integrated (6.3.1.3). There is an exemption for locations with less than 800
hours between 8 a.m. and 4 p.m. where the ambient drybulb temperature is between 55°F and
69°F.
Application Guide AG 31-003-1
65
Hybrid Plants
Figure 59 - Gas Fired Absorption Chiller
Mixing and matching different chiller types
increases the designer’s option in chiller plant
design. To meet small winter chilled water
loads, an air-cooled chiller might be included in
the chiller plant. The operator does not have to
run the cooling towers in winter and the chiller
is properly sized for the winter load. This is
common in health care applications with watercooled equipment (MRIs, linear accelerators,
etc.) The air-cooled chiller must be properly
selected for winter operation.
To diversify the chiller plant on energy sources,
an absorption chiller is often incorporated into
the chiller plant design. The absorption chiller
can operate on either plant steam or directly on
natural gas or #2 fuel oil. Either type allows the operator to shave demand peaks for the electrical
load. The absorption chiller can be in series or parallel (primary/secondary) with the electric chiller.
Chilled Water Requirements
Absorption chillers are not as flexible as centrifugal chillers in terms of chilled water flow rates and
supply water temperatures. Since the supply temperature and range must be the same in any parallel
chiller arrangement, the absorption chiller limitation may set the design.
In a series application, the absorption chiller can be upstream of the electric chiller. The warmer
return chilled water improves the efficiency of the absorption chiller by as much as 30%. This
arrangement automatically base loads the electric chiller. Until the return water reaches 49°F, the
absorption chiller won’t operate. Once the building load climbs above 50%, the electrical demand is
avoided by using the absorption chiller. In colder weather, either chiller can be operated. (reset the
absorption chiller setpoint to 44°F).
Condenser Flow Requirements
The condenser water needs of the absorption chiller are different from the electric chiller. The
electric chiller typically operates with 3 gpm/ton on the condenser side, whereas an absorption chiller
operates with higher flow rates. Table 7 lists the ARI typical flow rates for various types of chillers.
Condenser water temperature stability and reset are also more critical with an absorption chiller. In
addition, absorption chillers may require condenser water flow after the chiller is shut down, for as
much as 30 minutes, to cool the machine and avoid crystallization.
Table 7 - ARI Design Condenser Flow Rates
Chiller Type
STD
Condenser
EWT (°F)
Condenser Flow Rate
Vapor Compression Chillers
Single Effect, Indirect Fired Absorption Chiller
Double Effect, Indirect Fired Absorption Chiller
Double Effect, Direct Fired Absorption Chiller
ARI 550/590-98
ARI 560-2000
ARI 560-2000
ARI 560-2000
85
85
85
85
3.0
3.6
4.0
4.0
(US gpm)
Dedicated cooling towers and condenser pumps are straightforward. If a common cooling tower or
headered condenser pumps are being used, then the design has to account for the different design
requirements for electric and absorption chillers. One possibility might be to have the absorption
chillers selected with the same flow rate per ton as the electric chillers. McQuay absorption chillers
can be modified to operate with up to 15°F range with only minor performance changes. This change
will make it easier to have the condenser pumps interchangeable.
66
Application Guide AG 31-003-1
Heat Recovery and Templifiers™
General
Chiller plants collect all the energy releas-ed in the building. In addition, there is an additional 25%
more energy from the chillers themselves. This represents a lot of heat that can be used for other
processes within the building. The challenge is the heat is in a very low-grade form. It is difficult to
find many uses for 95°F condenser water. The solution is to use either heat recovery chillers or
Templifiers™, which can raise the water temperature.
Common uses for heat recovery water are:
Y
HVAC system reheat
Y
Domestic hot water
Y
Snow melting
Y
Process applications
Load Profiles
A key issue with heat recovery is to understand the load profile of the chiller plant and the load profile
of the system that requires the heat. It is absolutely necessary to have a cooling load at the same time
there is a requirement for heat. While this may seem obvious, many reheat systems are designed to
use heat recovery hot water when the chiller plant is producing little or no heat.
BTU/ft^2
Figure 60 - Cooling Load vs. Heating Load Profile
Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec
Month
Heating
Cooling
In many cases the cooling load is
declining as the heat load is
increasing. An example is reheat for
VAV.
Without a cooling load, no
heat can be collected. An analysis
must be performed to identify the size
and time of heating load. McQuay
Energy Analyzer™ can perform the
analysis and recommend heat
recovery, Templifier™ and source
chiller sizing. Then the cooling load
at the same time periods must be
identified. Some or all of the heat
from the cooling load can be used for
the heating load.
HVAC systems that require winter chilled water such as fancoils, buildings with process loads, etc.,
tend to be good candidates for a heat recovery chiller because of the large amount of time when there
is simultaneous heating and cooling.
Heat Recovery Chillers
There are two types of heat recovery chillers. Both can produce condenser water from 105 to 115°F
rather than the normal 95°F. Figure 61 shows the piping arrangement for a single condenser heat
recovery. Typically a heat exchanger is used to transfer the heat from the condenser loop into the hot
water loop. This is done to avoid contamination from the open tower condenser loop entering the hot
water loop. Using a heat exchanger introduces another approach into the system since the condenser
water will have to be about 2°F warmer than the hot water loop.
Application Guide AG 31-003-1
67
Figure 61 – Single Condenser Heat Recovery
Boiler Loop
Chilled Water
Pump
Cooling Tower
Condenser Water
Pump
Heat Exchanger
The second type has an additional
condenser shell that allows the
rejected heat to be rejected to a
separate heat recovery water loop.
Since the hot water loop is heated
directly by the refrigerant, warmer
water is possible for the same
condensing pressure (compressor
work) than with single condenser
recovery.
When heat recovery is not
required, the condensing pressure
can be lowered and the heat
rejected to the cooling tower at the typical condenser water temperature range. This reduces the
compressor work and improves the chiller efficiency. It is recommended that the chiller has a
dedicated cooling tower rather than a common cooling tower with other chillers in the plant. This will
avoid raising the condenser water to the other chillers and lowering their performance unnecessarily.
Heat Exchanger
Pump
3-Way Bypass
Valve
Figure 62 - Split Condenser Type Heat Recovery
Cooling Tower
Boiler Loop
Split Condenser
Heat Recovery
Chiller
Chilled Water
Pump
Figure 62 shows the piping
arrangement for a split type heat
recovery chiller. The hot water
loop flows directly through the
chiller. Any additional heat not
used by the hot water loop is
collected in the condenser loop
and rejected by the cooling tower.
Split condenser chillers are more
expensive but avoid the heat
exchanger and other piping
requirements.
Heat Recovery
Pump
3 Way Bypass
Valve
Heat recovery puts additional demand on either type of heat recovery chiller. To raise the refrigerant
condensing temperature high enough to produce the hotter water, the compressor must work harder.
This lowers the chiller efficiency and must be taken into account when evaluating the use of heat
recovery. Even when the chiller is operating in “normal” mode, the chiller efficiency will be less than
a standard chiller because it is not optimized for the lower lift application.
Another major issue is part load performance. As a centrifugal chiller unloads, it becomes more and
more difficult for it to produce high lifts. If the lift of the chiller is exceeded, it will stall and then
surge, which can severely damage the compressor. Most heat recovery load profiles increase the
heating requirement as the cooling load reduces, setting up a situation where the chiller will be
partially loaded but expected to produce hot water.
To remedy the problem, hot gas bypass should be included with any heat recovery chiller. While this
will protect the chiller from surging, it may also waste a lot of power. For instance, if the hot gas valve
opens at 25% capacity, any output between 0 and 25% capacity will consume the power used at 25%
capacity. In short, the chiller may become a very large electric resistance heater!
68
Application Guide AG 31-003-1
Heat Recovery Chiller Control
When a chiller is in heat recovery mode, it attempts to produce hot water as well as chilled water.
There are two common methods of control. The first is for the chiller to maintain a common
condenser return water temperature. For example, consider a chiller that is intended to produce
105°F supply hot water with 95°F return hot water at full load. This control sequence will attempt to
maintain the return water temperature at 95°F. The supply hot water temperature will then fluctuate
between 95 and 105 °F depending on the amount of heat rejected.
Figure 63 - Heat Recovery Chiller Control Options
Fixed Return Water Temperature
re
ratu
mpe
nt Te
igera
fr
e
er R
dens
Con
Supply
ecovery
Heat R
nt Temperature
Condenser Refrigera
105
Temperature
Temperature
105
H.R. Cond. Water Return
95
Leaving Chilled Water
44
Evaporator Refrigeran
t Temperature
10
50
Fixed Supply Water Temperature
100
% Cooling Load
Heat Recovery Supply
H.R. Cond. Wa
ter
Return
95
Leaving Chilled Water
44
Evaporator Refrigeran
t Temperature
10
50
100
% Cooling Load
Basing the control on the return water temperature is easier on the chiller in terms of light load lift.
During period of light cooling load, the required condensing pressure drops as shown in Figure 63.
This reduces the chance of a surge or stall situation and reduces the use of hot gas bypass. A fixed
return hot water system (during heat recovery mode) will mean the supply hot water temperature
fluctuates as the heating load changes (assuming a constant hot water flow rate. The changes are
generally small (3-5°F) The boiler can supplement the heat recovery and add enough heat to maintain
the return water temperature. The boiler control should be set up to provide 95°F return water during
heat recovery. If desired, during non-heat recovery heating mode, the boiler can operate on a fixed
(e.g. 180°F) supply water temperature.
A second control arrangement is for the chiller to attempt to maintain a fixed supply hot water
temperature. This arrangement provides, where possible; a constant supply temperature (105°F for
example) for the hot water system. It also requires the chiller to produce design condition refrigerant
condensing pressures even at very low chiller loads. This arrangement is harder on the chiller and
will generally produce less heat recovery than a control system that maintains a constant entering
water temperature.
Raising the hot water temperature is accomplished through cooling tower and bypass valve control.
To raise the water temperature for either single shell or split shell heat recovery, either the cooling
tower or the chiller bypass valve must be modulated to meet the required hot water temperature. (The
cooling tower water temperature will be the same as the hot water temperature!) Normal cooling
tower operation is overridden. When there is no heat recovery required (no heating load) the control
system should lower the condenser water temperature and follow whatever control sequence is being
used for conventional chillers (See Cooling Tower Controls, page 18).
Heat Recovery Chiller Selection
Proper heat recovery chiller selection requires a clear understanding of the chilled water and hot water
load profiles. To produce the best results, the chilled water plant design should be optimized to take
full advantage of the load profiles. A common practice is to design the chilled water plant as if there
was no heat recovery and then pick one of the chillers and rate it as a heat recovery chiller at design
Application Guide AG 31-003-1
69
cooling load conditions. The total heat of rejection from a heat recovery chiller operating at design
cooling is 1.25 times the design cooling capacity. While this sounds like a significant amount of
energy recovery, it does not mean the system will actually produce it. The chiller will only produce
this amount of heat recovery if it is fully loaded and all the other design parameters are met. The
following issues should be considered when selecting a heat recovery chiller:
Y
Chiller Sizing. The chiller should be sized as close to the expected cooling load during heat
recovery as possible. It is important to have the chiller operating as close as possible to 100%
cooling load during heat recovery to provide the best refrigerant lift and to use the least amount
of hot gas bypass. The optimal size requires annual energy analysis. McQuay’s Energy
Analyzer™ can provide the analysis and recommend a heat recovery chiller size.
Y
Hot Water Temperature Ranges. Chillers are typically selected based on 10°F ranges while hot
water systems are often designed for 20°F ranges. Using 20°F ranges for the chiller are not
recommended. Using tertiary piping for the chiller on the hot water loop allows the chiller to be
on a different temperature range and the pressure drop of the chiller is avoided when not in use.
Y
Hot Water Supply Temperature. Heat recovery chillers are limited in what they can produce.
The higher the water temperature, the more useful it is for heating. However, high supply water
temperatures are harder on the compressor, reduce the stable compressor envelope and lower the
chiller performance.
Y
Boiler Interaction. It is easy to become fixated on maintaining the hot water supply setpoint
when the real goal is to produce as much heat recovery as possible. Understand how the boiler
and chiller interact to produce hot water. Try to collect as much heat as possible from the chiller
(even if the supply water temperature is not met) and trim with the boiler to meet the required
heating load.
Y
Compressor Lift Limitations. The higher the compressor lift requirement, the smaller the stable
compressor envelope, and the sooner the compressor lift will be exceeded at part load.
Understand at what percentage of cooling load the compressor will no longer maintain the
required lift. Operation below this point will require hot gas bypass. Select the hot water control
sequence that produces the best result. Basing the hot water control on the return water
temperature may produce more heat recovery without hot gas bypass.
Chilled Water Plant Design for Heat Recovery
Any chiller plant design can include a heat recovery chiller. Generally, only one chiller in a multiple
chiller plant is a heat recovery type. It should be the first chiller that is activated during cooling.
Another design possibility is to add a heat recovery chiller with a tertiary loop, in the chilled water
return line. This chiller will reduce the load on the main chillers by lowering the return water
temperature. It will also allow all the heat recovered in the building to be available for heat recovery.
Chiller plant design can be “tuned” to optimize heat recovery. Here is a list of things to consider:
Y
Pick a chiller size that matches the chilled water load during heat recovery.
Y
Backload the chiller by the placement of the decoupler (See Decoupler Location, page 54).
Y
Consider series chillers where the upstream chiller is the heat recovery chiller.
Y
Use chilled water reset so the lift is reduced during heat recovery operation.
Y
Evaluate a VFD chiller, which will operate more efficiently when not in heat recovery mode.
Y
Avoid low chilled water design temperatures.
Impact on the Rest of the HVAC Design
Where heat recovery will be used for heating, the chiller should tie into the boiler return. A tertiary
loop is recommended so the chiller heat recovery temperature range can be different than the boiler
loop range. The flow rates for the boiler and the heat recovery will mostly likely be different as well.
70
Application Guide AG 31-003-1
A tertiary loop also allows the pressure drop through the heat recovery chiller to be avoided when
heat recovery is not possible.
Most heating systems are designed for 170°F average water temperature. The use of heat recovery
will require the heating system to operate with water in the 105 to 115°F range. Whereas single row
heating coils in terminal heating units would have worked with a conventional design, now 3 or 4row heating coils may be required. These coils will add to the capital cost of the project. Further,
they will increase the fan static pressure drop every hour the fan system operates.
Domestic hot water systems range from 120°F for showers, baths, etc to 140°F for kitchens. These
temperatures exceed the capabilities of a heat recovery chiller, however, a heat recovery chiller can be
used for preheat. When heat recovery is used for domestic hot water, local codes may require an
isolating heat exchanger.
Templifiers™
A Templifier™ is a water-to-water energy recovery device. It is capable of producing hot water in the
140 to 160°F range with a COP between 3 and 5.
Figure 64 – McQuay Templifier™
Templifiers™ can be used in any application where
heat recovery chillers are considered, as well as in
many other applications where hotter water is required
than can be produced by heat recovery chillers. Other
applications include geothermal, solar collectors,
ground source and closed loop water source heatpumps.
Figure 65 shows a Templifier™ used in a chiller plant
system. In this arrangement the Templifier™ can
produce 140 to 160°F from the heat of rejection of
Chiller 1. It can do this while still allowing normal
condenser relief for Chiller 1.
Figure 65 - Templifier™ in a Condenser Loop
Chilled Water
Pump
Boiler Loop
Condenser
Water Pump
Templifiers™ are designed to
maintain the heating water
setpoint regardless of source
water conditions within the
limits of the machine.
Cooling Tower
Std. Chiller
Templifier
95 °F
Templifier™ Control
85 °F
Templifier™
Selection
Templifier™ size should be
based on the heat load and the
85 °F
Templifier Pump
source chiller total heat of
rejection. The best method
for selecting the capacity is to perform an annual analysis and identify the balance point where the
heat source and the heat load are largest. This can be a very involved calculation requiring several
iterations. The McQuay Energy Analyzer™ can perform this annual analysis and provide a
recommended Templifier™ and source chiller size. The following are some alternative methods that
can be used as a starting point to evaluate a design:
130 °F
Application Guide AG 31-003-1
140 °F
3-Way Bypass
Valve
71
Y
If the intent is to provide reheat for a VAV system, use the design reheat load from the building
winter design load calculations. This will be enough heat to raise all the supply air from 55°F to
75°F with the VAV boxes at minimum flow. Assume the cooling load will be 50% of design. If
there are two equally sized chillers, then the source chiller will be fully loaded. The Templifier™
capacity should be the smaller of these two loads.
Y
For a constant volume system, do the same as above but use the summer design reheat. Constant
volume with reheat systems use large amounts of reheat even in warm weather.
Y
Fancoil systems offer an excellent opportunity since there is such a large overlap in heating and
cooling loads. Use the lesser of either the winter building envelope heat loss (less the ventilation
air) or the source chiller capacity times 1.25 for the chiller compressor work.
Y
For domestic hot water applications use the smaller of either the 50% of the chiller design load or
the design domestic hot water load.
Templifiers™ are selected based on the leaving heating water temperature and the leaving source
water temperature. In most cases, the designer knows the desired heating water temperature and the
entering source water temperature at building design conditions (For condenser water heat recovery,
this would be the condenser water temperature leaving the chiller). It is important to select the
Templifier™ based on the most demanding conditions expected during heat recovery. It is
recommended that the minimum entering condenser water for the chiller supplying the heat be set at
65°F. Assuming the chiller is operating at 50% capacity during heat recovery mode, the supply water
temperature to the Templifier™ would be 70°F (based on a 10°F range for the condenser water).
The more source flow through the Templifier™, the warmer the leaving source water temperature will
be. When there is additional source flow available, it is recommended that the flow through the
Templifier™ be increased until the design temperature range is 5°F or the design flowrate is 4.8 US
gpm/ton. Using the source supply water temperature and the Templifier™ load, the source leaving
water temperature can be calculated. More information on selecting Templifiers™ can be found in
McQuay product catalog PM Templifier.
Chilled Water Plant Design for Templifier™ Heat Recovery
Templifiers™ can use the condenser water of any chiller for a heat source. In some applications, it
may make sense to change the source chiller size to optimize heat recovery. It should be the first
chiller that is activated during cooling. A common condenser water loop for all the chillers in the
plant allows all the heat rejected by the chiller plant to be used for heat recovery by the Templifier™.
Preferentially loading the source chiller by the placement of the decoupler (See Decoupler Location,
page 54) can also increase the heat available for recovery.
Templifier™ Impact On the Rest Of the HVAC Design
Where heat recovery will be used for reheat, the Templifier™ should tie into the boiler return. A
tertiary loop is recommended so the Templifier™ temperature range can be different than the boiler
loop range. The flow rates for the boiler and the Templifier™ will mostly likely be different as well.
A tertiary loop also allows the pressure drop through the Templifier™ to be avoided when heat
recovery is not possible.
Most heating systems are designed for 180°F average water temperature. A Templifier can provide
140 to 160°F water, which is typically enough to provide reheat during the spring and fall periods
without having to increase the size of reheat coils. During the winter season, the hotter water from the
boiler can be used for the larger loads experienced by the reheat coils. The reheat coils should be
sized for the winter load and boiler design supply temperature.
Domestic hot water systems range from 120°F for showers, baths, etc to 140°F for kitchens. The
Templifier can supply water at these temperatures. When heat recovery is used for domestic hot
water, local codes may require an isolating heat exchanger.
72
Application Guide AG 31-003-1
ASHRAE Standard 90.1
ASHRAE Standard 90.1 makes several references to condenser heat recovery. Here is a list of items:
Y
There is a requirement for condenser heat recovery to be used to preheat domestic hot water for;
Y
Facilities open 24 hours a day.
Y
Total heat of rejection from the chiller plant is 6,000,000 Btu/hr or greater (About a 400-ton
plant).
Y
Domestic hot water load exceeds 1,000,000 Btu/hr.
Y
The system must be able to either use 60% of the chiller peak rejection load at design
conditions or preheat the domestic hot water to 85°F. (6.3.6.2)
Y
There is an exemption for the requirement for economizers if condenser heat recovery is used for
domestic hot water. (6.3.1d)
Y
There is an exemption for simultaneous heating and cooling if 75% of the energy used for reheat
comes from energy recovery such as condenser heat recovery. This can be helpful with some
VAV with reheat designs. (6.3.2.1c)
Y
There is an exemption for pool covers for pools heated to 90°F if 60% of the heat comes from
site recovered energy.
Application Guide AG 31-003-1
73
Heat Recovery and Templifier™ Example
Consider an acute care hospital in Chicago. The facility is 480,000 ft², 3 story with a
1600 ton chiller plant and a 22,000 mbh boiler plant. The air system is constant volume
with reheat. Constant volume with reheat is common in health care because the air
turnover rates are specified. This system requires reheat year round.
Let’s compare a base building (no energy recovery) with Templifier™ and a split
condenser heat recovery chiller. The base building uses two 800 ton dual compressor
centrifugals. The Templifier™ version has a 472 ton unit with a 4.4 COP. It is providing
hot water at 140°F. The source chiller condenser pump head was increased by 20 ft
since there are two chiller barrels in series. The heat recovery version has a 400 ton
Heat recovery chiller producing 105°F hot water at 0.73 kW/ton. The second chiller is a
1600 ton dual compressor centrifugal. The supply fan static pressure was increased
0.20 inches to off set the deeper coils required by the low hot water temperature.
14000000
12000000
10000000
kWh
8000000
6000000
4000000
2000000
0
Chillers
Pumps
Base Building
Towers
Fans
Templifier
Boiler
HW Pumps
HR Chiller
The graph above was generated from data produced by Energy Analyzer™. The chiller
work increased when energy recovery was added. The Templifier™ penalty was the
highest, however it produces the warmest hot water. The pump work was higher for the
Templifier™ example because the condenser pump head was increased. The two heat
recovery examples saved tower fan work since less energy was being rejected but the
savings are minor. The heat recovery chiller example saw a 4% increase in fanwork
due to the increased static pressure. Bother heat recovery examples saved significant
boiler work. The Templifier™ savings are greater because all the Templifier™
compressor work can be subtracted from the boiler load. Both heat recovery options
require an additional circulating pump that operates when in heat recovery mode.
Overall, both heat recovery options saved over 6 million kBtu/year. The annual
operating savings for the Templifier™ is $108,000 over the base building. Both heat
recovery options have less than 2 year paybacks and offer 80% Return on investment.
74
Application Guide AG 31-003-1
Variable Primary Flow Design
Modern DDC controllers on chillers allow the possibility of variable flow design. Traditional
thinking has been that the chiller should see constant flow and then the load will vary directly with the
return fluid temperature. Allowing variable flow means the cooling load can vary either with the
return fluid temperature or a change in the chilled water flow. It requires modern controllers to deal
with two variables and provide stable chiller operation.
Basic Operation
Figure 66 shows a two chiller variable primary flow system. Variable primary flow can be applied to
single, parallel or series chiller plants although parallel is the most common. The control valve at the
cooling loads are two-way type so the chilled water flow varies with the cooling load. The primary
pump for the chillers circulates the chilled water throughout the building. The chilled water flow
varies through the chillers as well. This is the main difference between variable primary flow and
primary/secondary flow.
Figure 66, - Basic Variable Primary Flow Operation
VFD Primary
Pump
2160 GPM
54 °F
Isolating Valves
(Open)
Building Load
900 Tons
(75% Load)
Two 600 Ton Chillers
Each at 450 Tons
(Balanced Load)
Flow Meter
1080 gpm
Each
Bypass Valve
Closed
There is a bypass line to
maintain minimum flow through
the chillers only. Whenever the
chilled water flow is above
minimum, the bypass is closed.
Chiller 1 On
Chiller 2 On
Variable primary flow provides
pump savings over primary
secondary systems because all
the chilled water being pumped
is being used for cooling. In a
primary /secondary system, any
flow through the decoupler
consumes pump power but
provides no cooling.
44 °F
Basic Components
Figure 67 - Variable Primary Flow System
Chillers
Bypass Line
Used to Ensure Minimum
Flow Through Chillers
VFD Primary Pump
Automatic Isolating Valves
Application Guide AG 31-003-1
Apply Diversity to Flow
Use 2 Way Valves
Almost any type of chiller can be
used including air- cooled and
absorption. The chiller must have
a unit controller capable of
dealing with both a change in
flow and a change in return
temperature. In most cases, the
controller should be a modern
digital type using PID control
loops.
Check with the
manufacturer
whether
the
controller is capable of variable
primary flow.
Usually, the
controller can be upgraded on an
existing unit if required.
75
The range of flow rates in the chiller is limited at the low end by laminar flow in the tubes (2 to 3 fps
tube velocity) and at the high end by tube erosion and vibration (10 to12 fps tube velocity). Chiller
selection software typically tries to pick a tube velocity of around 6 fps which provides a good
balance between water pressure drop and heat transfer performance. Half the typical design flow rate
will result in 3 fps tube velocities which is about the minimum. The actual minimum should be
provided by the manufacturer and is often included in computer selections.
Selecting the chiller with tube velocities
at design conditions near 10 fps allows
the system flow to be turned down to
30% of design flow. This may be
advantageous where there is only one
chiller in the system with few operating
hours at design flow.
☺Tip: Usually, the minimum flow rate of a chiller is
50% of the design flow rate. This value can be used
to size the bypass line. The bypass line should be
capable of handling the minimum flow of the largest
chiller.
In most cases, the chillers will be the same size. The flow ranges and capacities must be carefully
considered so that there are no operating points where no combination of chillers can meet the load.
For example, if two evenly identical chillers have a minimum flow rate 60% of design, there will be a
“hole” between 50 and 60% of plant capacity. One chiller can meet the load up to 50% of plant
capacity. However, at say 55% two chillers will be required but the flowrate will be less than the
minimum required. Careful chiller selection (preferred since it is more energy efficient) and the use
on the bypass will resolve this problem.
Pumps
The chilled water pump is variable flow. (See Variable Flow Pumps, page 13). They are sized to
provide enough head to circulate chilled water throughout the building. Automatic isolating valves
are provided in front of each chiller to stop flow when the chiller is not operating. Pumps can be
dedicated to each chiller or in the main return line (as shown in Figure 67). Common pumps allow
overpumping and sharing a spare pump.
Bypass Line
The bypass should be sized for the minimum flow rate of the largest chiller being used. It is only used
to provide minimum flow to a chiller when the flow requirement through the chiller plant is less than
the chiller minimum flow.
The bypass line can be located between the chillers and the loads (as shown in Figure 67). This is the
same location as a decoupler in a conventional primary/secondary system. The bypass line could also
be placed at the end of the cooling loop. The bypass control valves will see a smaller pressure drop
but there may be some additional pump work.
Alternatively, some cooling loads could use three-way valves, which would provide the minimum
flow required. On the other hand these valves will bypass chilled water any time they are not
operating at design load, which wastes pump work and leads to low delta T syndrome.
When flow is required through the bypass line, it must be controlled. A modulating two or three-way
valve is required.
Variable Primary Flow Sequence of Operation
Although a variable primary flow system is no more difficult to design than a primary/secondary
system, the control sequences must be carefully thought out and commissioned. A building
automation system (BAS) capable of variable primary flow is a must. Direct communication between
the BAS and the chiller unit controllers is strongly recommended as well. This can be accomplished
with controls communication (McQuay Protocol Selectablity™, for example) using industry open,
standard protocols such as BACnet or LonTalk.
76
Application Guide AG 31-003-1
Primary Pump Control
The primary pump is controlled in the same manner as a secondary pump in a primary/secondary
system (Refer to Variable Flow Pumps, page 13).
Modulating both the flow and temperature range through a chiller requires time for the chiller
controller to respond. Many factors influence the rate of change of flow including the chiller type, the
chiller controller logic and the actual load on the chiller at the time. Some field adjustment of the rate
of change time should be expected during commissioning. A good starting point is 10% change in
flow per minute. This will effect the modulating rate of the primary pumps and the terminal unit
control valves.
Bypass Line Valve Control
It is recommended that each chiller should have a flow meter. The meter can be used to recognize
both minimum and maximum flow constraints. Individual chiller meters allow each chiller’s flow rate
to monitored, which may be advantageous in some chiller plant control concepts such as overpumping
or deliberately operating multiple high part load efficient chillers in lieu of a single chiller.
It is possible to use only one flow meter in the common chilled water supply line upstream of the
bypass line. Assuming only one chiller is operating when minimum flow becomes an issue, the flow
measured at this point would be the flow through the operating chiller.
The bypass line control valve is controlled by a signal from the flow meter of the operating chiller.
The control system should recognize the chiller and know the minimum flow rate for that chiller. In
most cases the chillers are all the same and hence there is only one minimum flow rate for the entire
chiller plant. The bypass line control valve is modulated to maintain the minimum chiller flow. This
must be done slowly. Fast changes in the bypass line flow may cause the primary pump control loop
to hunt as it recognizes a change in total chilled water flow.
Starting an Additional Chiller
The first step is recognizing an additional chiller is required. The BAS can use the individual chiller
flow meter and the chiller load as indicators that another chiller is required. Another chiller is
required when either the chiller capacity or the chiller design flow rate has been reached.
Using the maximum flow rate rather than the design flow rate will “overpump” the chiller. The
pressure drop will exceed design conditions and increase the primary pump work. The advantage is
starting another chiller and its ancillary equipment (condenser pump, cooling tower etc) is staved off.
This is a good method for counteracting low delta T syndrome.
A different approach is to use chillers with excellent part load performance and deliberately operate
multiple chillers at part load. Refer to Low Delta T Syndrome, page 84.
Adding a chiller is more complicated than other chiller plant systems as explained in the example
below. Each chiller must have an automatic isolating valve. When the chillers are all the same size,
the valves can be two-position type. These valves must open and close slowly.
Adding a Chiller Example
In a two-chiller variable primary flow system, the first chiller is operating at 100% load.
The plant load increases so that a second chiller is required. At this moment, all the
chilled water is flowing through the operating chiller, which is cooling the chilled water
from 54°F to 44°F.
To start the second chiller, the building automation system will open the isolating valve for
the second chiller. If done quickly, the operating chiller will see the flow rate cut in half.
At 100% capacity, the operating chiller will effectively double its chilled water temperature
range so that the supply water temperature will become 34°F! The chiller controller will
start to respond to the sudden change in load but will most likely trip on a freeze or low
pressure safety.
Application Guide AG 31-003-1
77
To reduce the possibility of a nuisance trip, the following sequence is recommended. Prior to opening
the isolating valve on the chiller to be started, use either the demand limiting feature or some form of
controls communication (McQuay MicroTech II control’s Protocol Selectablity™ for example) to
reduce the capacity of the operating chiller(s) to 50%. Next, slowly open the isolating valve on the
chiller to be started. Enable the added chiller and allow it to start. Release the demand limiting on
the original chiller(s). During the chiller startup, accurate chilled water supply temperature control
will be lost for a few minutes. In most HVAC applications, this is acceptable. For close tolerance
designs, a different concept may be required. There are other methods for adding chillers. The goal is
to add the chiller and avoid a nuisance trip or damage to the equipment.
Shutting Down a Chiller
A chiller can be shut down when the sum of the chilled water flows through all the operating chillers
is less than the design capacity of the remaining chiller(s). If the concept of using two efficient part
load chillers rather than one conventional chiller is being used, then different criteria will be required.
To shut down a chiller, the chiller is commanded off by the BAS. Once the chiller is off, its isolating
valve is slowly closed. It is important to provide some time for the remaining chillers to ramp up to
the additional load.
Variable Primary Flow with Different Sized Chillers
Using different sized chillers (and hence different chilled water flow rates,) in a variable primary flow
system further increases the complexity. Providing the correct amount of chiller water flow to each
chiller becomes an issue. Using dedicated variable flow primary pumps allows chiller specific flow
control but creates pump selection and control issues.
If a common pumping plant is used for all chillers then the chiller isolating valves may need to be
modulating to control the correct flow rate for each chiller. This may lead to a hunting problem
between the valves and the primary pump.
Staging of chillers also becomes complex. Which size chiller should be added or subtracted must
now be considered. Variable primary flow chiller plants with different sized chillers have been
successfully designed and implemented but it is recommended that the value of different sized chillers
be carefully weighed against the additional complexity.
Training and Commissioning
Variable primary flow systems are more difficult to commission than other chiller plant designs and
this should not be ignored. All parties involved in the choice, design, commissioning and operating of
a variable primary flow system should understand this and be committed to a successful project.
Operator training is especially important. It is critical to a successful installation that a thorough
operator training program be part of the project.
78
Application Guide AG 31-003-1
Variable Primary Flow Example
Using the model office building from the earlier examples, the graph below compares
parallel chiller constant flow with variable primary flow and primary secondary flow.
500000
450000
400000
350000
kWh
300000
250000
200000
150000
100000
50000
0
Chillers
Variable Primary Flow
Pumps
Towers
2 Chiller Primary/Secondary Flow
Fans
2 Chiller Parallel Flow
The parallel chiller constant flow arrangement can be used as a benchmark. Both the
variable primary flow and primary/secondary flow arrangements have better chiller
performance because the chillers can be stage off when not required.
The major savings comes from reduced pump work. The pumps are smaller (flow is
based on design load rather than connected load) and the flow varies with the load.
The variable primary flow system outperforms the primary secondary system slightly
because the flow is varied through the chiller whereas the primary/secondary system
pumps excess flow through the decoupler.
Application Guide AG 31-003-1
79
Low Delta T Syndrome
Low delta T syndrome occurs when the design chilled water temperature range is not maintained.
Any variable flow system can experience low delta T and the problem is exacerbated at part load. In
severe cases, the chilled water range has dropped from 12°F design to 2°F. When this occurs, the
flow rate must be increased significantly to provide cooling in the building. The following example
illustrates the issue:
Low Delta T Example
Figure 68 shows a basic primary/secondary loop operating at full load. In this example, the system
design load is 800 tons, the flow rates and temperatures are at standard ARI conditions and the load
has a two-way control valve. The loop with the chiller is called the primary loop. The loop with the
load is the secondary loop. The common pipe is sometimes referred to as the decoupler.
Figure 68 - Primary/Secondary Loop at Full Load
At full load, the design flow
of 1920 gpm passes through
Building Load
54 °F
800 Tons
the chiller, the two pumps,
0 gpm Flow Through
the load, and back to the
54 °F Return Water
Decoupler
To Chiller
chiller. There is no flow
through the common pipe.
800 Ton Chiller
At 800 Tons
At first, it would appear that
the flow is being pumped
twice. Although this is true,
the total head is split between
44 °F
Chiller 1 - On
the two pumps. The primary
Primary Pump
1920 gpm
pump is only sized for the
primary loop of which the
chiller is the main pressure
Secondary Pump
Chiller 2 - Off
1920 gpm
drop. The secondary pump
is sized for the pressure drop
“outside the mechanical
room”. The higher pressure drops and larger piping arrangements in the secondary loop justify the
variable flow.
Figure 69 - Primary/Secondary Loop at 50% Load
49 °F
49 °F Return Water
To Chiller
54 °F
Building Load
400 Tons
960 gpm Flow Through
Decoupler
800 Ton Chiller
At 400 Tons
44 °F
Flow
44 °F
Chiller 1 - On
Primary Pump
1920 gpm
Chiller 2 - Off
80
Secondary Pump
960 gpm
Figure 69 shows the same
example operating at 50%
capacity.
The two-way
control valve at the load has
reduced the flow in the
secondary loop to 960 gpm.
The delta T across the load
remains at 10°F.
The primary pump is a
constant flow pump sized for
the chiller design flow. It
remains constant at 1920
gpm. The additional flow
not required in the secondary
loop passes through the
common pipe to the chiller
Application Guide AG 31-003-1
return line. The 44°F fluid from the common pipe mixes with the 54°F return fluid to 49°F. The
chiller maintains its design flow of 1920 gpm with 49°F RWT and 44°F LWT. The chiller sees a 50%
load.
The example in Figure 69 demonstrates how diversity is applied to flow in the secondary loop. The
variable flow in the secondary loop offers excellent pump operating savings and first cost saving in
pipe sizing. The constant flow in the primary loop provides the chiller with stable operating
conditions.
Figure 70 - Primary/Secondary Loop at Low Delta -T
50 °F
50 °F Return Water
To Chiller
50 °F
1280 gpm Flow
Backwards
Through Decoupler
800 Ton Chiller
At 480 Tons
50 °F
Flow
44°F
Chiller 1 - On
Building Load
800 Tons
It is important to understand what
happens if design temperature
range is not maintained. This is
known as a low delta T syndrome.
Figure 70 shows the previous
example with an 800 ton load but
only a 6°F delta T. This could be
caused
by several
factors
including poor valve selection or
dirty coils.
Primary Pump
1920 gpm
To meet the 800-ton load
requirement, the control valve
44 °F
Secondary Pump
Chiller 2 - Off
will respond by opening and
3200 gpm
allowing more flow through the
load. The secondary pump will
respond in turn by increasing the secondary loop flow to 3200 gpm to meet the load. The primary
pump is only supplying 1920 gpm so 1280 gpm will flow “backward” through the common pipe to
meet the 3200 gpm requirement. Two problems now occur. First, the supply fluid temperature in the
secondary loop will rise when the primary fluid and the return fluid mix. The higher fluid temperature
will cause the control valve to open further, making the problem worse. The second problem is the
return water to the chiller is only 50°F so the chiller only sees a 480-ton load. This system will not
function well under these conditions.
Figure 71 - Primary/Secondary Loop with Low Delta T Reality
Obviously the above example
Building Load
can’t occur. Figure 71 shows
49 °F
800 Tons
50 °F
what does happen. A second
640 gpm Flow Through
49 °F Return Water
chiller has to be started to
Decoupler
To Chiller
balance the flow in the
44 °F
Two 800 Ton Chiller
primary loop with the flow in
Each At 400 Tons
the secondary loop.
Although running two chillers
provides a working solution,
44 °F
many of the features of the
Chiller 1 - On
Primary Pump
primary/secondary approach
1920 gpm
are lost. The flow in the
secondary is high, wasting
Secondary Pump
Chiller 2 - On
3200 gpm
pumping energy. Two primary
Primary Pump
1920 gpm
pumps have to operate when
only one should be doubling
the primary pump horsepower. Finally, two chillers are operating (and their condenser water pumps)
when only one should be.
Flow
Application Guide AG 31-003-1
81
Low Delta T Syndrome Causes and Solutions
Many things can lead to low delta T syndrome. The following is a list of common causes and
solutions.
Three-Way Valves
Three-way valves bypass unheated chilled water around the cooling coil and into the return line.
They will increase the flow rate of the system while not raising the chilled water temperature.
The solution is not to use them. A common reason for including three-way valves in variable flow
systems is to avoid a decoupler. While the three-way valves will bypass water when it is necessary to
do so just like a decoupler. They will also bypass water when it is not necessary to do so. Using
three-way valve instead of a decoupler wastes pump work and causes the low delta T syndrome.
Another common reason is to maintain some flow in the loop so the water remains at setpoint. The
goal here is to be able to provide cold chilled water to a cooling coil as soon as it calls for it, rather
than having to flush the lines. While this may be important in some situations, it generally is not
critical in most HVAC applications. Also consider that chilled water is flowing through the piping at
4 feet per second. Chilled water produced in the basement will travel to the top of a 10-story building
in less than 30 seconds.
AHU Setpoints Lowered Below Design
The control loop for the supply air temperature in a typical AHU is a simple arrangement. There is a
temperature sensor in the supply air stream. If the temperature is too high, the controller opens the
control valve. If the temperature is too low, the valve closes. A common problem is temperature
setpoint for the supply air are lowered from the original design to the point where the coil cannot
produce the requested supply air temperature. In this case, the control loop will keep open the chilled
water valve in an attempt to cool the water further. The result will be a wide open valve bleeding
chilled water in to the return line.
The solution is to reset all the AHU supply air setpoints back to design settings. Often these get
changed in the first place because a space served by the AHU is not satisfied. Lowering the setpoint
will probably not solve the problem and will create a new problem. Once the settings are back to
design, the original problem can be identified and remedied.
System Components Not Designed For the Same Temperature Range
For a variable flow system to operate properly, all the components must be designed for the same
chilled water temperature range including the chillers and the coils at the loads. If, for instance, the
AHUs in a building are designed for 14°F range while the fan coils are sized for 10°F, it is very likely
the system will suffer from low delta T syndrome.
The solution can be very complex. Where possible, converting the system to a common temperature
range is desirable but often this is cost prohibitive. Another solution is to use tertiary piping.
Consider a university campus where buildings were built in different eras with different temperature
ranges. Now all the buildings are to be served by a common chiller plant. The chiller plant can be
operated with one temperature range and a supply water temperature colder than required by any
other load. Tertiary piping at each building can be used to match the supply temperature setpoint and
temperature range required.
Coils and Control Valves Not Properly Selected
Improperly selected coils and control valves can lead to excessive chilled water consumption to meet
the load requirements.
The solution is to properly select coils and control valves. Control Valve Basics, page 20, covers
valve selection detail. It is important that the valve actuator have the necessary power to close the
valve against the system pressure. Improper coil selection can also lead to difficulties.
82
Application Guide AG 31-003-1
Coils Piped “Backwards”
Figure 72 - Proper Coil Connections
Coils must be connected so the water flow
through the rows of the coil is counterflow
to the airflow. When coils are improperly
connected, the coil performance can drop
by as much as 15%. When this occurs, the
chilled water control valve will go wide
open because the coil is in effect, 15%
undersized.
Out
In
The solution is to properly connect the
coils.
Water Flow Comes In At Bottom,
Leaves From Top
And Moves Counter To Air Flow
Improper Tertiary Piping
Tertiary piping is discussed in, page 55. If there is not a difference in the tertiary loop supply
temperature and the main supply line, there is a possibility that the two-way control valve that returns
tertiary water to the return line will go wide open in an attempt to get the tertiary loop the same
temperature as the supply line. This will end up being a short circuit from the supply line to the
return.
The solution is to make sure the tertiary loop is operating at a higher temperature than the main supply
line.
Dirty Coils
Dirty coils on either the water or airside will reduce the effectiveness of the cooling coil. The control
valve will increase flow in an attempt to offset the coil performance loss and the temperature range
will not be maintained.
The solution is to clean the coils.
Airside Economizers and Make-Up Air Units
Coils that cool supply air with a large percentage of outdoor air are sized for a design day. During
periods of lighter loads, the supply air temperature to the coil drops. For instance, when the ambient
air temperature is 57°F, an AHU with an economizer will switch to 100% outdoor air and thus the
inlet air temperature will now be 57°F. Leaving chilled water can never be warmer than the inlet air
temperature. When the inlet air temperature is less than the design return water temperature, low
delta T syndrome can occur. In the above example, if the design water temperatures are 44°F supply
and 58°F return, it will not be possible to obtain 58°F with 57°F entering air.
The solution is to reduce the chilled water range to minimize the occurrences where the return water
temperature is higher than the supply air temperature. This has to be weighed against the advantages
of reducing pumping cost from using a higher chilled water range.
Chilled Water Reset
Chilled water reset raises the chilled water supply temperature to reduce the lift and thus the
compressor work of the chiller. While this a good goal, it now means a higher supply water
temperature than used in the design and selection of the coils. When the reduced load allows a coil to
meet the load with warmer water, this approach works. On the other hand, when the warmer water
Application Guide AG 31-003-1
83
causes the control valves to overflow the coil in an attempt to meet setpoint, then reset can lead to low
delta T syndrome.
The solution is careful evaluation and application of chilled water reset. The first step is whether any
energy will be saved at all. Raising the chilled water set point will help the chiller. However, it will
most likely increase the flow in a variable flow system, which can easily offset any chiller savings.
Assuming there are savings available, then chilled water reset is possible. Chilled water reset should
not be based on return water temperature but on valve position at the loads.
Other Solutions
The following is list of additional solutions to low delta T syndrome.
Check Valve In
Decoupler
Check Valve In
Decoupler
Figure 73 - Check Valve in
Decoupler
Adding a check valve in the
decoupler changes the nature of the
primary/secondary system. When
the primary flow exceeds the
secondary flow, the system is
decoupled and additional primary
flow can pass through the decoupler
and checkvalve.
When the secondary flow exceeds the primary flow, however, then the pumps are truly in series. The
secondary pump will “pull” water through the primary pump as it attempts to maintain system
pressure. The chiller flow rate will increase beyond design flow rate. It is extremely unlikely that
enough flow will be drawn through the chiller to damage it. In most cases, the chiller can handle a
50% increase in flow which would result in a huge pressure drop. It is unlikely the pumps could
provide enough head.
By overpumping a chiller the system can meet the required flow rate and load, and avoid starting a
second chiller and the additional pumps and tower.
Increasing the chiller flow rate offers some unique possibilities. If there is condenser relief available,
then the chiller may be able to produce more than it’s design capacity (For example a 100-ton chiller
may produce 110 tons with condenser relief). To take advantage of the extra capacity, the system
would have to increase the temperature range across the chiller (difficult to do since the system is
typically experiencing just the opposite!) or the flow rate would have to be increased. By
overpumping a chiller, it may be possible to produce more than the design capacity and avoid
additional pumps and tower work.
Adding a check valve effectively makes the system variable primary flow during low delta T intervals.
System control becomes more complicated as well. How and at what point is a second chiller added?
It is recommended that check valves not be added to primary/secondary systems as part of the design.
If variable primary flow is the intention, then the system should be designed with that goal in mind.
When a system is exhibiting signs of low delta T syndrome, the previous remedies should be
investigated first prior to adding a check valve.
VFD Or Dual Compressor Chillers
The main problem with low delta T syndrome is the increase in energy usage due to multiple chillers,
pumps and towers operating to meet a light load. VFD and dual compressor chillers offer a different
solution. The high part load efficiency of these kinds of chillers promotes operating two chillers
rather than one to meet the load. Two VFD or dual compressor chillers operating partly loaded can
84
Application Guide AG 31-003-1
consume less energy than one chiller operating fully loaded. If the energy savings offset the penalty
of the pumps and tower, then VFD and dual compressor chillers are good solutions to low delta T
syndrome.
Oversize Primary Pumps
Oversizing the primary pumps allows the additional flow to be pumped through the chillers and
maintain the primary flow above the secondary flow. Overpumping a chiller can also allow any
additional capacity (See Check Valve In Decoupler, page 84) in the chiller to be utilized.
Reduce Temperature Range on Primary Side
Reducing the chilled water temperature range on the primary side increases the flow rate for the same
capacity. During periods of light load, when low delta T syndrome occurs, the lower delta T/higher
flow rate on the primary side will counter act problems on the secondary side.
One draw back is the additional pump work on the primary side wastes energy at all operating points.
The possible savings offered by avoiding low delta T syndrome at light loads may be offset by the
penalty created at other operating points.
Add Flow Control Valves at Each Coil
Adding flow control valves at each load rated for the maximum flow rate will ensure the load won’t
consume too much chilled water. From the chiller plant perspective, this will avoid low delta T,
However, space serviced by the coil may not be satisfied. In addition, most control valves create a
pressure drop that the chilled water pumps must be sized to overcome. Overcoming the additional
pressure drop will add to the annual cost of operating the pumps.
Variable Primary Flow
Low delta T syndrome occurs because of issues at the loads (coils). These will happen with variable
primary flow or primary secondary systems. Variable primary flow (VPF) does allow several
solutions to be easily implemented:
Y
Do not have a decoupler that allows return chilled water to flow into the supply side. Return
chilled water will raise the supply water temperature and exacerbate the problem.
Y
VPF allows chillers to be overpumped. See Check Valve In Decoupler, page 84.
Y
VPF systems typically have flow meters, which can help the operator recognize a low delta T
situation and be used by the BAS to remedy the problem.
Application Guide AG 31-003-1
85
Process Applications
Process applications can place unique demands on chiller plants. All parties involved in a process
application should be fully aware that it is a process and not an HVAC application to avoid any
confusion.
Process Load Profiles
Process loads can be broken down in to specialized environments and chilled water for the actual
processes. Specialized environments such as low relative humidity (RH) for pharmaceutical or
confectionery manufacturers are an extension of conventional HVAC design.
Chilled water for processes and equipment can be quite a bit different than HVAC design. Remember
that process loads generally have very little to do with ambient conditions. It is quite possible that the
process will be operating at 5% on the hottest day of the year and 100% on the coldest day. It is
extremely important to gather as much information about the process, the load profile the operating
conditions, etc., as possible. Adding a process load to an HVAC chiller plant without consideration
can lead to very poor performance.
The designer should gather at least the following information:
Y
The process design load. Is it constant? Is it stepped or a batch load?
Y
Are there multiple process loads with different needs? Do they have to be handled individually
or can a common system serve both?
Y
The operating hours. Is it every hour of the year? Is it only in the summer? This will lead to a
discussion about redundancy. In HVAC design, redundancy often means there are at least two
pieces of equipment but not necessarily enough capacity to meet the design load if one of them
should fail. In process applications, redundancy usually means 100% backup so no production
time is lost.
Y
The critical nature of the process. Can the customer live without chilled water? If so, how long?
All chiller plant equipment must be serviced at some point offline. How will this be
accommodated?
Y
Will the chiller plant service HVAC loads as well? If so, the combination of the two load profiles
will need to be considered.
Constant Load Profiles
Constant load profiles have very little change for long periods of time. The goal here is to optimize
the chiller plant for full load performance.
Stepped Load Profiles
Stepped profiles are most common. An example of a stepped process is cooling molds for injection
molding. If there are only two molds, then shutting down one line is an instant 50% reduction in
chiller plant load. The quick changes in load must be accounted for. The chiller plant should be
optimized to performance well at the various “plateaus” in a stepped load profile.
Batch Load Profiles
Batched operations, such as a bakery, require a relatively sudden amount of chilled water and then
nothing for an extended period of time. This profile lends itself to some form of chilled water storage
and charging in anticipation of the load. The load size and the intervals are critical to proper
operation.
86
Application Guide AG 31-003-1
Condenser Relief
As mentioned earlier, there is typically no
☺Tip: As the cooling tower load goes from 100%
correlation between process load and the
to 0%, the supply water temperature approaches
ambient conditions. Most chiller ratings
wetbulb. This can be used to estimate the entering
and design are based on HVAC load
condenser water temperature for part load rating
profiles which are tied to the ambient
of a process chiller.
conditions. This is very true for condenser
relief where ARI 550/590-98 allows a
condenser relief profile based on HVAC design. For example consider a centrifugal chiller used in a
process application. The process load drops to 25% on the hottest day of the year. It would not be
expected in an HVAC load to ever operate at 25% on a design day. The chiller may not even be able
to meet the lift requirement at these conditions. Chillers used for process must be rated at process
conditions.
Supply Condenser Water
Temperature
Figure 74 - ARI 550/590 vs. Process Condenser Relief
As the load on a cooling tower goes
from 100% to 0% the leaving
90
condenser water approach will go from
85
design (For example there is a 7°F
Relief
Process
80
approach with 85°F supply water
78°F Wet Bulb
temperature and 78°F ambient wetbulb)
75
to 0°F. This can be used to estimate the
70
correct condenser relief for a process
65
chiller on a design day.
ARI Relief
60
For instance, in the example given
above, the entering condenser water at
55
25% load and ARI 550/590 conditions
0
25
50
75
100
would be 65°F. Using the above
% Chiller Load
relationship for cooling towers, the
actual entering condenser water
temperature would be 79.75°F. Process chillers should be selected where possible to operate down to
minimum capacity with the condenser water temperature being the same as the design wetbulb. If
stable operation for the chiller is exceeded, then hot gas bypass should be added.
Winter Design
Most process chillers operate year-round. In colder climates, winter design must be considered. The
equipment manufacturer should be involved is assessing the safe, reliable operation of chiller in
subfreezing conditions.
The very high operating hours provide an excellent opportunity for using the cooling towers and a
heat exchanger to directly cool the process load in a manner similar to waterside free cooling (Refer
to Water-Side Free Cooling, page 61).
Chilled Water Volume
Process loads with sudden changes in load are a challenge for a chiller. The best method to deal with
them is to have a large enough flywheel effect in the chilled water system to limit the rate of change
seen by the chiller. There may be enough chilled water volume in the system to provide the
necessary flywheel effect. If not, then a tank may be required. Different chillers have different limits
for rate of change and thus require different system volumes. Refer to Minimum Chilled Water
Volume, page 89 and the chiller product catalog for details.
Application Guide AG 31-003-1
87
Temperatures and Ranges
Chilled water supply temperature and chilled water ranges must be reviewed and based on the needs
of the processes served. It should be first surmised what chilled water temperatures and ranges are
required and whether a single supply water temperature will work. The use of a tertiary pump can
allow for different temperatures but the chiller plant will have to provide all the chilled water at the
lowest required temperature. This will lower the chiller efficiency for the entire plant. It may be
advantageous to have medium and low temperature chilled water systems.
In many process applications such as injection molding, avoiding condensation is important; in which
case the chilled water temperature should be above the space dewpoint. The warmer the chilled
water, the more efficient the chillers. There are processes that require chilled water warmer than the
chiller is rated to provide. This can be resolved with mixing valves.
Temperature ranges can also vary a lot. For instance, a process may require 60°F supply water and a
30°F temperature range. These conditions are beyond the range of most chillers so the system design
must accommodate them.
Figure 75 - Process Piping Arrangement
3-Way
Bypass
Valve
Cooling
Tower
Chilled Water
Pump
44 °F
60 °F
Condenser
Water Pump
54 °F
Chilled Water
Pump
88
3-Way
Mixing Valve
90 °F
3 Way Process
Mixing Valve
Figure 75 shows a typical
piping arrangement to deal
with high supply water
temperature, large temperature
range and small chilled water
volume.
This arrangement allows the
chiller to operate at optimized
conditions while meeting the
requirements of the process.
The storage tank provides the
necessary buffer to limit the
rate of change.
Application Guide AG 31-003-1
Minimum Chilled Water Volume
The volume of chilled water in the chilled water system acts as a damper and smoothes out the effects
due to load change. Process loads tend to be the most abrupt and can cause the chiller to shutdown on
a safety if the system is not designed correctly. As well, when a chiller is close coupled to a large
dominant air conditioning load (A chiller connected to a single large air handling unit for example)
the chiller can “hunt” on control valve and result in unstable operation.
There are other issues, which need to
be considered as well. For instance, a
☺Tip: The volume of a coil can be estimated by using
small chiller using scroll compressors
0.15 US Gal/sq ft-row. For instance, a 48” x 60”, 5 row
will change capacity in discrete steps
coil has 20 ft² x 5 rows x 0.15 = 15 US Gal.
(For example, a four compressor
chiller will have a stepped capacity of
25, 50, 75 and 100% cooling capacity). If the load is between the steps (For example 65% capacity),
then the chiller will operate at the step above and then the step below the actual load. The chiller will
require the chilled water fluid volume to “dampen” the effect of the chiller either over or under
cooling the chilled water.
Another example is where the load drops below the minimum capacity the chiller can operate. In this
case, the chiller will cycle a compressor on and off to meet the load. If there is not enough fluid in the
system, the compressor will incur too many starts, which will result in undue wear.
Estimating System Volume
To evaluate whether there is sufficient volume in the system requires first estimating the amount of
fluid in the system. To find the volume, the amount of fluid in the chiller evaporator, piping and coils
must be added together. Table 8 provides the fluid volume per foot for standard piping. Chiller
evaporator volumes can be found in the chiller catalogs and/or computer printouts. Coil volumes are
often provided by computer selection outputs or can be estimated by assuming 0.15 US gal per sq.
Ft.- Row.
Table 8 – Fluid Volume for Standard Pipe
Nominal Pipe Dia.
(in.)
US Gal. Per
Linear Ft.
Nominal Pipe Dia.
(in.)
US Gal. Per
Linear Ft.
1
1½
2
2½
3
3½
4
5
0.037
0.092
0.153
0.221
0.343
0.462
0.597
0.945
6
8
10
12
14
16
18
20
1.35
2.37
3.88
5.63
6.63
8.57
11.1
13.9
Evaluating System Volume
Whether there is sufficient fluid volume can be found using the following formula:
Ts
Vw =
{
500*
Application Guide AG 31-003-1
TD
(H1 – H2)
}{
+
TD
H2
}
89
Where:
Ts = Time from start to start (Minutes)
Vw = Fluid volume (US gal)
H1 = Minimum operating capacity of the chiller (Btu/Hr)
H2 = Minimum applied load on the chiller (Btu/Hr)
TD = Dead band of chiller controller (°F)
The values used in this formula should come from the specific chiller and application. Where these
values are not immediately known, Table 9 provides some guidance. Chiller short cycling is a serious
issue that can shorten the life or damage equipment and result in poor performance. Whenever a
chiller is closed coupled to a single large load, the designer should review this issue carefully.
Table 9 – Typical Parameters for Various Chiller Types
Chiller Type
Scroll
Compressor
Reciprocating
Compressor
A/C
Screw
W/C
Screw
Centrifugal
Dual Compressor
Centrifugal
90
Ts = Time between
starts
(Minutes)
H1 = Minimum operating
capacity of the chiller
(Btu/Hr)
TD = Dead band of
chiller controller
(°F)
15
25
4
15
25
4
30
25
4
30
25
4
30
10
4
30
5
4
Application Guide AG 31-003-1
Minimum Fluid Volume Example
Consider a 200-ton system using an air cooled screw chiller with two 100 ton compressors.
The fluid flow rate is 480 US gpm and the minimum load (H2) is 10-tons.
Is a chilled water storage tank necessary and if so, how large?
The first step is to estimate the volume of fluid in the system.
Chiller Evaporator = 40 US Gal
Piping = 50 ft of 5 in. Sched. 40 pipe. From Table 8, the volume is 45 US Gal.
The Coil is 48” x 60” by 5 row. Using the rule of thumb, the volume is 15 US Gal.
The total system volume (Vw ) is 100 US. Gal.
The next step is to estimate the minimum required volume.
The chiller unit controller has a 4°F deadband (TD) from the time it cycles off to the time it
will start again. To protect the compressors, a 30 minute start to start (Ts ) period is
desirable. The minimum capacity (H1) of the chiller is 25 tons.
30
Vw =
{
500*
4
(300,000 – 120,000)
}{
+
4
120,000
}
= 1080 US Gal
Since the system only has 100 US Gal volume, a 980 US Gal storage tank is required.
A common rule of thumb is to use a minimum time for all the fluid in the system to circulate
once. In this example, the time is 2.25 minutes. This is not reliable however since a large
temperature range would have a smaller flow rate and yield a different minimum volume
requirement. Yet the volume is really controlled by how fast the minimum load raises the
temperature and how fast the minimum chiller capacity lowers the temperature.
It is worth considering what would happen if a storage tank is not included. The minimum
chiller capacity is 2.5 times larger than the actual load. Even at minimum capacity, the
chiller will “over cool” the chilled water. The supply chilled water temperature will drop
below setpoint until it reaches the minimum allowable temperature, then the chiller will shut
off. While the chiller is off, the 10-ton load will raise the chilled water temperature until the
temperature reaches the high limit of the chilled water deadband. If the compressor start
to start time has not been reached, the chiller will not start and the chilled water
temperature will continue to rise. Poor system performance may occur. Shortening the
start to start time will resolve the performance, however it may put undue stress on the
chiller. The reverse is also true, extending the start to start time will protect the chiller but
will lower performance.
Application Guide AG 31-003-1
91
Conclusions
Chillers and chiller plant design provide the designer a very flexible solution to meet the needs of the
project. This Guide only covers the basics. The references indicate additional material the designer
may wish to review. Key things for the designer to remember are the full load performance of a
chiller plant is not a good indicator of its overall performance. Many systems may have the same full
load energy requirement but are quite different at part load. Since chiller plants rarely operate at full
load, part load performance is critical to good annual performance. For more information please
contact your McQuay Sales Representative or McQuay International at www.mcquay.com.
92
Application Guide AG 31-003-1
References
1998 ASHRAE Refrigeration Handbook ASHRAE. Atlanta, Ga
1999 ASHRAE HVAC Applications Handbook ASHRAE. Atlanta, Ga
2000 ASHRAE HVAC Systems and Equipment Handbook ASHRAE. Atlanta, Ga
2001 ASHRAE Fundamentals Handbook ASHRAE. Atlanta, Ga
3 GPM/Ton Condenser Water Flow Rate: Does It Waste Energy? - Kirsner, Wayne ASHRAE
Journal, February 1996. ASHRAE. Atlanta Ga.
All Variable Speed Centrifugal Chiller Plants - Hartman, Thomas. ASHRAE Journal, September
2001. ASHRAE. Atlanta Ga.
ANSI/ASHRAE Standard 15-2001, Safety Standard for Refrigeration Systems.. ASHRAE.
Atlanta, Ga.
ANSI/ASHRAE Standard 34-2001, Designation and Safety Classification of Refrigerants.
ASHRAE. Atlanta, Ga.
ANSI/ASHRAE Standard 90.1-2001, Energy Standard for Buildings Except Low-Rise
Residential Buildings. ASHRAE. Atlanta, Ga.
ARI Standard 550/590 – Water Chilling Packages Using The Vapor Compression Cycle– AirConditioning and Refrigeration Institute. 1998. Arlington, Va.
ARI Standard 560 – Absorption Water Chilling and Water Heating Packages – Air-Conditioning
and Refrigeration Institute. 2000. Arlington, Va.
ASHRAE 90.1 Users Manual.2000. ASHRAE. Atlanta, Ga.
Chilled Water System Forensics – Luther, Kenneth. 2002. ASHRAE Transactions AC-02-6-2.
ASHRAE, Ga.
Control Valve Selection – Haines, Roger. September 1980. Heating, Piping and Air Conditioning.
Controlling Chillers in Variable Flow Systems - Avery, Gil ASHRAE Journal, February 1998.
ASHRAE. Atlanta Ga.
Cooling Tower Optimization - Shelton, Sam, Charles Joyce. ASHRAE Journal, June 1991.
ASHRAE. Atlanta Ga.
Cooling Towers Used For Free Cooling - Murphy, Dan. ASHRAE Journal, June 1991. ASHRAE.
Atlanta Ga.
CSA B52-99, Mechanical Refrigeration Code. CSA International. Rexdale Ont. Canada.
Degrading Chilled Water Plant Delta-T: Causes and Mitigation - Taylor, Steven. ASHRAE
Transactions AC-02-6-1. ASHRAE, Ga.
Engineering Data Book - Valves – LIT-237VB. 1994 Johnson Controls. Milwaukee, Wn.
How to Raise Chilled Water Differentials - Fiorino, Donald. ASHRAE Transactions AC-02-6-3.
ASHRAE, Ga.
Improving the Efficiency of Chilled Water Plants - Avery, Gil ASHRAE Journal, May 2001.
ASHRAE. Atlanta Ga.
Near-Optimal Control of Cooling Towers for Chilled Water Systems – Braun, J.E., G. T.
Diderrich. 1990. ASHRAE Transactions SL –90-13-3. ASHRAE, Ga.
Piping Chillers to Variable Volume Chilled Water Systems - Rishel, James. ASHRAE Journal,
July, 1994. ASHRAE. Atlanta Ga.
Pressure and Flow Control in Hot and Chilled Water Piping – Hallanger, Erling Oct. 1982.
Heating, Piping and Air Conditioning..
Pumping Energy and Variable Frequency Drives - Bernier, Michel. Bernard Bourret. ASHRAE
Journal, December 1999. ASHRAE. Atlanta Ga.
Selecting Valves and Piping Coils - Avery, Gil ASHRAE Journal, April 2000. ASHRAE. Atlanta
Ga.
Technology of Balancing -. Armstrong. Armstrong. Scarborough, On. Canada.
Application Guide AG 31-003-1
93
Varying Chilled Water Flow with Success - Lunnenberg, Tom E Source Report ER-01-11, July
2001. E Source, Boulder Co.
McQuay Engineering Solutions, Will Variable Evaporator Flow Negatively Affect Your
Centrifugal Chiller? – Edition 3, April 2003. McQuay International, Minneapolis, Mn.
McQuay Engineering Solutions, Air Cooled Chillers-Benefits and Design Tips – Edition 7, April
2001. McQuay International, Minneapolis, Mn.
McQuay Engineering Solutions, Series Chillers, What’s Old Is New Again. January 2002.
McQuay International, Minneapolis, Mn.
94
Application Guide AG 31-003-1
Post Office Box 2510, Staunton, Virginia 24402 USA • (800) 432-1342 • www.mcquay.com
AG 31-003-1 (10/02)
Lakshmi Narayana