ABSTRACT An ionic polymer based on a polythiophene backbone with appended imidazolium moieties wa... more ABSTRACT An ionic polymer based on a polythiophene backbone with appended imidazolium moieties was successfully implemented as a donor material in fully solution-processed efficient bi-layer solar cells prepared by the low impact meniscus coating technique. High fill factors and device reproducibility were obtained, even for ultrathin polymer layers, indicating excellent film formation properties and good compatibility with solution processing techniques. The possibility of smooth counter ion exchange, allowing solubility modification and efficiency tuning, enables exploration of new functionalities and other device architectures.
ABSTRACT Three distinct low bandgap copolymers are synthesized by the combination of N-(2′-propyl... more ABSTRACT Three distinct low bandgap copolymers are synthesized by the combination of N-(2′-propylpentanoyl)dithieno[3,2-b:2′,3′-d]pyrrole (DTP) and (fluorinated) 2,3-bis[5′-(2”-ethylhexyl)thiophen-2′-yl]quinoxaline (Qx) and these PDTPQx derivatives are investigated as electron donor materials in bulk heterojunction polymer solar cells. Due to the DTP N-acylation and the introduction of the Qx units, both the open-circuit voltage (Voc) and the short-circuit current density (Jsc) increase compared to previous devices based on DTP-type donor polymers. Organic solar cells with an average Voc of 0.67 V, a Jsc of 12.57 mA/cm² and a fill factor of 0.54 are obtained, affording a power conversion efficiency of 4.53% (4.81% for the top-performing device), a record value for (N-acyl-)DTP-based polymer solar cells devoid of special interlayer materials. Despite further enhancement of the Voc, the solar cell efficiency declines for the fluorinated PDTPQx copolymers because of the inability to achieve a finely intermixed bulk heterojunction blend nanomorphology.
ABSTRACT The effect of fluorination on the optoelectronic properties and the polymer:fullerene so... more ABSTRACT The effect of fluorination on the optoelectronic properties and the polymer:fullerene solar cell characteristics of PCPDTQx-type (poly{4-(2’-ethylhexyl)-4-octyl-4H-cyclopenta[2,1-b:3,4-b’]dithiophene-alt-2,3-bis[5’-(2’’-ethylhexyl)thiophen-2’-yl]quinoxaline}) low bandgap copolymers is reported. The introduction of fluorine atoms on the quinoxaline constituents is an effective way to lower the HOMO and LUMO energy levels of the alternating copolymers, resulting in an enhanced open-circuit voltage for the devices based on the fluorinated polymers (~0.1 V per F added). Furthermore, fluorination also improves the charge carrier mobility in the bulk heterojunction blends. Despite the formation of unfavorable photoactive layer morphologies, the best solar cell performance is obtained for the copolymer prepared from the difluorinated quinoxaline monomer, affording a power conversion efficiency of 5.26% under AM 1.5G irradiation, with an open-circuit voltage of 0.83 V, a short-circuit current density of 11.58 mA cm-2 and a fill factor of 55%.
ABSTRACT The molecular weight of poly(3-hexylthiophene) is an important factor influencing the ph... more ABSTRACT The molecular weight of poly(3-hexylthiophene) is an important factor influencing the photovoltaic properties of bulk heterojunction organic solar cells based on this material. However, since different synthetic processes or repetitive soxhlet extractions - generally applied to obtain the different molecular weight batches under study - result in samples with simultaneously varying regioregularity (RR) and polydispersity index (PDI), it has not been possible yet to find an unambiguous correlation between the molecular weight and the photovoltaic performance. In the present work preparative gel permeation chromatography is introduced as a versatile technique to fractionate the donor polymer and thereby obtain a systematic variation of the number average molecular weight (Mn = 11-91 kg mol−1) with an almost constant PDI and RR. Polymer crystallinity and conjugation length are evaluated by UV-Vis spectroscopy, rapid heat-cool calorimetry and selected area electron diffraction, and are found to be deeply affected by Mn. This in turn influences the behavior of the charge transfer state energy, measured via Fourier transform photocurrent spectroscopy, and therefore the open-circuit voltage. The short-circuit current is also affected by Mn, but mainly due to a change in absorption coefficient. The apparent recombination order is shown to be linked to the morphology of the polymer:fullerene blend and is determined using transient photovoltage and photocurrent techniques. Finally, a correlation between recombination and fill factor is also suggested.
Here we report the fabrication of nanofibre-based organic phototransistors (OPTs) using preformed... more Here we report the fabrication of nanofibre-based organic phototransistors (OPTs) using preformed poly(3-hexylthiophene) (P3HT) nanofibres. OPT performance is analysed based on two important parameters: photoresponsivity R and photosensitivity P. Before testing the devices as OPTs, the normal organic field-effect transistor (OFET) operation is characterized, revealing a surface-coverage-dependent performance. With R reaching 250 A W(-1) in the on-state (V(GS) = -40 V) and P reaching 6.8 × 10(3) in the off-state (V(GS) = 10 V) under white light illumination (I(inc) = 0.91 mW cm(-2)), the best nanofibre-based OPTs outperform the OPTs fabricated from a solution of P3HT in chlorobenzene, in which no preformed fibres are present. The better performance is attributed to an increase in active layer crystallinity, a better layer connectivity and an improved edge-on orientation of the thiophene rings along the polymer backbone, resulting in a longer exciton diffusion length and enhanced charge carrier mobility, linked to a decreased interchain coupling energy. In addition, the increased order in the active layer crystallinity induces a better spectral overlap between the white light emission spectrum and the active layer absorption spectrum, and the absorption of incident light is maximised by the favourable parallel orientation of the polymer chains with respect to the OPT substrate. Combining both leads to an increase in the overall light absorption. In comparison with previously reported solution-processed organic OPTs, it is shown here that no special dielectric surface treatment or post-deposition treatment of the active device layer is needed to obtain high OPT performance. Finally, it is also shown that, inherent to an intrinsic gate-tuneable gain mechanism, changing the gate potential results in a variation of R over at least five orders of magnitude. As such, it is shown that R can be adjusted according to the incident light intensity.
ABSTRACT In this Proceedings paper, we report on the synthesis of a family of polythiophene-based... more ABSTRACT In this Proceedings paper, we report on the synthesis of a family of polythiophene-based conjugated polyelectrolytes, both homopolymers and random copolymers varying in the building block ratio and counter ions, toward a better fundamental understanding of the structure-property relations of these ionic derivatives in organic photovoltaics. One of the ionic homopolymers was successfully implemented as a donor material in fully solution-processed efficient bi-layer solar cells (up to 1.6% PCE in combination with PC71BM) prepared by the low impact meniscus coating technique. On the other hand, these imidazolium-substituted polythiophenes were also applied as materials for electron transport layers (ETLs), boosting the I-V properties of PCDTBT:PC71BM solar cell devices up to average PCE values of 6.2% (~20% increase), which is notably higher than for previously reported ETL materials. Advanced scanning probe microscopy techniques were used to elucidate the efficiency enhancing mechanism.
In pursuit of highly preorganized macrocyclic host molecules for the complexation of anions, a se... more In pursuit of highly preorganized macrocyclic host molecules for the complexation of anions, a series of oxacalix[2]arene[2]pyrimidine-based bis(thio)ureido receptors were synthesized and fully characterized. The pincer-like 1,3-alternate conformation of the oxacalix[4]arene scaffold, essential for an efficient host-guest interaction, was visualized by single-crystal X-ray analysis and supported by variable-temperature NMR studies. The anion binding properties of the receptors were evaluated via (1)H NMR titration experiments, showing intermolecular interactions with H(2)PO(4)(-), AcO(-), BzO(-), and Cl(-) ions. The host molecule bearing 4-nitrophenyl substituents on the bisurea binding pocket showed association constants in the range of 200-400 M(-1) in the strongly competitive solvent mixture of DMSO/0.5% H(2)O.
ABSTRACT An ionic polymer based on a polythiophene backbone with appended imidazolium moieties wa... more ABSTRACT An ionic polymer based on a polythiophene backbone with appended imidazolium moieties was successfully implemented as a donor material in fully solution-processed efficient bi-layer solar cells prepared by the low impact meniscus coating technique. High fill factors and device reproducibility were obtained, even for ultrathin polymer layers, indicating excellent film formation properties and good compatibility with solution processing techniques. The possibility of smooth counter ion exchange, allowing solubility modification and efficiency tuning, enables exploration of new functionalities and other device architectures.
ABSTRACT Three distinct low bandgap copolymers are synthesized by the combination of N-(2′-propyl... more ABSTRACT Three distinct low bandgap copolymers are synthesized by the combination of N-(2′-propylpentanoyl)dithieno[3,2-b:2′,3′-d]pyrrole (DTP) and (fluorinated) 2,3-bis[5′-(2”-ethylhexyl)thiophen-2′-yl]quinoxaline (Qx) and these PDTPQx derivatives are investigated as electron donor materials in bulk heterojunction polymer solar cells. Due to the DTP N-acylation and the introduction of the Qx units, both the open-circuit voltage (Voc) and the short-circuit current density (Jsc) increase compared to previous devices based on DTP-type donor polymers. Organic solar cells with an average Voc of 0.67 V, a Jsc of 12.57 mA/cm² and a fill factor of 0.54 are obtained, affording a power conversion efficiency of 4.53% (4.81% for the top-performing device), a record value for (N-acyl-)DTP-based polymer solar cells devoid of special interlayer materials. Despite further enhancement of the Voc, the solar cell efficiency declines for the fluorinated PDTPQx copolymers because of the inability to achieve a finely intermixed bulk heterojunction blend nanomorphology.
ABSTRACT The effect of fluorination on the optoelectronic properties and the polymer:fullerene so... more ABSTRACT The effect of fluorination on the optoelectronic properties and the polymer:fullerene solar cell characteristics of PCPDTQx-type (poly{4-(2’-ethylhexyl)-4-octyl-4H-cyclopenta[2,1-b:3,4-b’]dithiophene-alt-2,3-bis[5’-(2’’-ethylhexyl)thiophen-2’-yl]quinoxaline}) low bandgap copolymers is reported. The introduction of fluorine atoms on the quinoxaline constituents is an effective way to lower the HOMO and LUMO energy levels of the alternating copolymers, resulting in an enhanced open-circuit voltage for the devices based on the fluorinated polymers (~0.1 V per F added). Furthermore, fluorination also improves the charge carrier mobility in the bulk heterojunction blends. Despite the formation of unfavorable photoactive layer morphologies, the best solar cell performance is obtained for the copolymer prepared from the difluorinated quinoxaline monomer, affording a power conversion efficiency of 5.26% under AM 1.5G irradiation, with an open-circuit voltage of 0.83 V, a short-circuit current density of 11.58 mA cm-2 and a fill factor of 55%.
ABSTRACT The molecular weight of poly(3-hexylthiophene) is an important factor influencing the ph... more ABSTRACT The molecular weight of poly(3-hexylthiophene) is an important factor influencing the photovoltaic properties of bulk heterojunction organic solar cells based on this material. However, since different synthetic processes or repetitive soxhlet extractions - generally applied to obtain the different molecular weight batches under study - result in samples with simultaneously varying regioregularity (RR) and polydispersity index (PDI), it has not been possible yet to find an unambiguous correlation between the molecular weight and the photovoltaic performance. In the present work preparative gel permeation chromatography is introduced as a versatile technique to fractionate the donor polymer and thereby obtain a systematic variation of the number average molecular weight (Mn = 11-91 kg mol−1) with an almost constant PDI and RR. Polymer crystallinity and conjugation length are evaluated by UV-Vis spectroscopy, rapid heat-cool calorimetry and selected area electron diffraction, and are found to be deeply affected by Mn. This in turn influences the behavior of the charge transfer state energy, measured via Fourier transform photocurrent spectroscopy, and therefore the open-circuit voltage. The short-circuit current is also affected by Mn, but mainly due to a change in absorption coefficient. The apparent recombination order is shown to be linked to the morphology of the polymer:fullerene blend and is determined using transient photovoltage and photocurrent techniques. Finally, a correlation between recombination and fill factor is also suggested.
Here we report the fabrication of nanofibre-based organic phototransistors (OPTs) using preformed... more Here we report the fabrication of nanofibre-based organic phototransistors (OPTs) using preformed poly(3-hexylthiophene) (P3HT) nanofibres. OPT performance is analysed based on two important parameters: photoresponsivity R and photosensitivity P. Before testing the devices as OPTs, the normal organic field-effect transistor (OFET) operation is characterized, revealing a surface-coverage-dependent performance. With R reaching 250 A W(-1) in the on-state (V(GS) = -40 V) and P reaching 6.8 × 10(3) in the off-state (V(GS) = 10 V) under white light illumination (I(inc) = 0.91 mW cm(-2)), the best nanofibre-based OPTs outperform the OPTs fabricated from a solution of P3HT in chlorobenzene, in which no preformed fibres are present. The better performance is attributed to an increase in active layer crystallinity, a better layer connectivity and an improved edge-on orientation of the thiophene rings along the polymer backbone, resulting in a longer exciton diffusion length and enhanced charge carrier mobility, linked to a decreased interchain coupling energy. In addition, the increased order in the active layer crystallinity induces a better spectral overlap between the white light emission spectrum and the active layer absorption spectrum, and the absorption of incident light is maximised by the favourable parallel orientation of the polymer chains with respect to the OPT substrate. Combining both leads to an increase in the overall light absorption. In comparison with previously reported solution-processed organic OPTs, it is shown here that no special dielectric surface treatment or post-deposition treatment of the active device layer is needed to obtain high OPT performance. Finally, it is also shown that, inherent to an intrinsic gate-tuneable gain mechanism, changing the gate potential results in a variation of R over at least five orders of magnitude. As such, it is shown that R can be adjusted according to the incident light intensity.
ABSTRACT In this Proceedings paper, we report on the synthesis of a family of polythiophene-based... more ABSTRACT In this Proceedings paper, we report on the synthesis of a family of polythiophene-based conjugated polyelectrolytes, both homopolymers and random copolymers varying in the building block ratio and counter ions, toward a better fundamental understanding of the structure-property relations of these ionic derivatives in organic photovoltaics. One of the ionic homopolymers was successfully implemented as a donor material in fully solution-processed efficient bi-layer solar cells (up to 1.6% PCE in combination with PC71BM) prepared by the low impact meniscus coating technique. On the other hand, these imidazolium-substituted polythiophenes were also applied as materials for electron transport layers (ETLs), boosting the I-V properties of PCDTBT:PC71BM solar cell devices up to average PCE values of 6.2% (~20% increase), which is notably higher than for previously reported ETL materials. Advanced scanning probe microscopy techniques were used to elucidate the efficiency enhancing mechanism.
In pursuit of highly preorganized macrocyclic host molecules for the complexation of anions, a se... more In pursuit of highly preorganized macrocyclic host molecules for the complexation of anions, a series of oxacalix[2]arene[2]pyrimidine-based bis(thio)ureido receptors were synthesized and fully characterized. The pincer-like 1,3-alternate conformation of the oxacalix[4]arene scaffold, essential for an efficient host-guest interaction, was visualized by single-crystal X-ray analysis and supported by variable-temperature NMR studies. The anion binding properties of the receptors were evaluated via (1)H NMR titration experiments, showing intermolecular interactions with H(2)PO(4)(-), AcO(-), BzO(-), and Cl(-) ions. The host molecule bearing 4-nitrophenyl substituents on the bisurea binding pocket showed association constants in the range of 200-400 M(-1) in the strongly competitive solvent mixture of DMSO/0.5% H(2)O.
Uploads
Papers