Autogener Schneldbrenner mit abgeflachtem Brennerkopf. Der vorliegende,
zum Abtrennen der Nietköpfe vernieteter Werkstücke mit abgeflachtem Brennerkopf
versehene Autogenschneidbrenner erfüllt seine Aufgabe dadurch besonders gut, daß
der abgeflachte Brennerkopf durch einen Sporn noch eine gewisse Neigung zum Nietkopf
erhält, der ihn aber auch gleichzeitig zum leichten Umfahren des Nietkopfes befähigt.
Handelt es sich dabei um weitgehendste Schonung der vielfach recht wertvollen Werkstücke,
so hat der im wesentlichen parallel zum Werkstück und in dessen möglichster Nähe
verlaufende Schneidsauerstoffkanal eine sich von der Flachseite abwendende, also
nach oben ansteigende Mündung. Dadurch wird mit Sicherheit verhindert, daß der Schneidstrahl,
trotzdem er an der Unterkante des Nietkopfes ansetzt, sei es auch erst in größerer
Entfernung, das zu entnietende Werkstück trifft.Autogenous high-speed burner with flattened burner head. The given,
For cutting off the rivet heads of riveted workpieces with a flattened torch head
provided oxy-fuel cutting torch does its job particularly well in that
the flattened burner head still has a certain inclination towards the rivet head due to a spur
which at the same time enables him to easily move around the rivet head.
If this involves the greatest possible protection of the often very valuable workpieces,
so it is essentially parallel to the workpiece and as close as possible to it
running cutting oxygen channel a turning away from the flat side, so
upward rising mouth. This will definitely prevent the cutting beam,
even though it starts at the lower edge of the rivet head, even if it is a larger one
Distance that hits the workpiece to be riveted.
Wenn auch der neue Autogenschneidbrenner in erster Linie für das Abtrennen
vorstehender Nietköpfe bestimmt ist, so ist er doch keineswegs darauf beschränkt,
vielmehr können damit auch versenkte-Nietköpfe ausgeschnitten werden, wozu das Brennerrohr
mit einer spitz zulaufenden, in Art eines Zirkelschenkels verwendbaren Stütze ausgerüstet
ist, zu dem das Brennermundstück den Gegenschenkel liefert.Even if the new oxy-fuel cutting torch is primarily used for cutting off
protruding rivet heads is intended, it is by no means limited to
rather, it can also be used to cut out countersunk rivet heads, including the burner tube
Equipped with a tapering support that can be used in the manner of a compass leg
is to which the burner mouthpiece supplies the counter leg.
Eine beispielsweise Ausführungsform des neuen Autogenschneidbrenners
ist in der Zeichnung in Abb. i einer Ansicht dargestellt; Abb. 2 und 3 sind zwei
zueinander senkrechte Längsschnitte durch das flache Brennermundstück.An example embodiment of the new oxy-fuel cutting torch
is shown in the drawing in Fig. i a view; Fig. 2 and 3 are two
mutually perpendicular longitudinal sections through the flat burner mouthpiece.
Der mit dem Zuführungsrohr a für den Schneidsauerstoff und den Zuführungsrohren
b für das Heizgas versehene Autogenschneidbrenner bekannter Art hat an dem Knie
des zum Mundstücke überleitenden Schenkels a1 einen Sporn f. Das als Halbkegel,
d. h. auf der dem Werkstück g, g1 zugewendeten Seite e1 in bekannter Weise flach
ausgebildete Mundstücke hat die üblichen zum Anschluß der Rohre d, b, b dienenden
Gewindebohrungen i, h, lt. Die aus den Bohrungen zur Mündung führenden Kanäle
h, m, n1 sind einseitig, und zwar möglichst nahe der Flachseite e1 verlegt (Abb.
2 und 3). Die eigentliche Austrittsdüse k1 für den Schneidsauerstoff steigt mit
ihrer Mündung etwas nach oben an, entfernt sich also mit dieser von der Flachseite.The known type of oxy-fuel cutting torch provided with the supply pipe a for the cutting oxygen and the supply pipes b for the heating gas has a spur f on the knee of the leg a1 leading to the mouthpiece Mouthpieces of flat design have the usual threaded bores i, h, lt for connecting the tubes d, b, b . The channels h, m, n1 leading from the bores to the mouth are laid on one side, as close as possible to the flat side e1 (Fig . 2 and 3). The actual outlet nozzle k1 for the cutting oxygen rises slightly upwards with its mouth, so it moves away from the flat side with it.
Durch Umfahren der in der Zeichnung oberen Hälfte des Nietkopfes d
mit der Miindung des Brennerkopfes e, e1, wobei der Brenner selbst mit der Spitze
des "Sporns f auf dem Werkstück g, g1 aufgesetzt ist, wird der Kopf d von seiner
Unterseite her abgeschnitten, wozu einmal das flache Anliegen des Brennerkopfes
am Werkstück und dann die unmittelbare Nähe des Kanals k sowie die dem Mundstücke,
e1 durch den Sporn erteilte Neigung Anlaß gibt. Das sich von der Flachseite e1 abwendende
Ende der Düse k1 führt dabei den Schneidstrahl derart, daß er hinter dem Kopf d
nicht etwa auf -das Blech g auftrifft.By circumnavigating the upper half of the rivet head d in the drawing
with the mouth of the burner head e, e1, the burner itself with the tip
of the "spur f is placed on the workpiece g, g1, the head d of his
Cut off the underside, including the flat contact of the burner head
on the workpiece and then the immediate vicinity of the channel k and the mouthpiece,
e1 gives rise to the inclination given by the spur. The one turning away from the flat side e1
The end of the nozzle k1 guides the cutting jet in such a way that it is behind the head d
does not strike the sheet g.
Handelt es sich um das Entfernen versenkter Nietköpfe, dann wird der
Autogenbrenner mit der an einem Arm r des Rohres b
befestigten Stütze
s auf das Werkstück g, g1 aufgesetzt und dann der versenkte Kopf mit dem Mundstück
e, e1 umfahren.If it is a matter of removing countersunk rivet heads, then the oxy-fuel torch with the support s attached to an arm r of the tube b is placed on the workpiece g, g1 and then the countersunk head is bypassed with the mouthpiece e, e1.