<Desc/Clms Page number 1>
Vertrauehsunterbrecher für Elektrizitätszähler mit einer Einstellvorrichtung für den
Stromverbrauch.
EMI1.1
<Desc/Clms Page number 2>
auf welcher der Hebedaumen 18 befestigt ist, gedreht. Wenn der Zähler ausser Betrieb ist und der Einstellapparat die Null zeigt (Fig. i und 2), nimmt der Schalter 8 eine schräge Stellung ein, bei welcher er auf dem parallelstehenden Hebedaumen ruht.
Um den Zähler wieder in Betrieb zu setzen, ist der Schalter in die Schlussstellung zu bringen und der Apparat auf irgendeine beliebige Zahl von Kw.-Stunden gleichzeitig einzustellen. Zu diesem Zwecke ist zuerst der Riegel 14 zurückzuschieben, damit der Hebedaumen 18 durch Umdrehung der Kurbel 16 sich vertikal stellt. Das Schlüsselloch 19 ist somit frei geworden und die Welle 1 zugänglich, so dass dem Einstellen nichts im Wege steht. Nachdem der Schalter in die Schlussstellung gebracht wurde, könnte der Zähler auch ohne Betätigung der Einstellvorrichtung registrieren.
Um dies zu verhindern, ist das dosische Schloss so angeordnet, dass der Schlüssel nur in der Sperrstellung des Riegels entnommen werden kann ; eine passende Hemmung ist so angebracht, dass dem Schlüssel eine volle Umdrehung nicht gestattet ist.
Dürfte sich also der Fall ergeben, dass absichtlich oder versehentlich die Nockenscheibe 6 in der Nullstellung verblieben ist, also die Einstellvorrichtung nicht betätigt wurde, so würde der Fortsatz 11 nicht bis zum Schalter herausragen. Um den Schlüssel zu entnehmen, muss das dosische Schloss zugesperrt und damit der Hebedaumen wieder in die schräge Stellung gebracht werden. Dem Schalter werden nun beide Stützen (Fortsatz 11 und Hebedaumen 18) fehlen und der Zähler wird ausgeschaltet.
Zur Entlastung des Zählers, welcher durch verschiedene von der Einstell-und Schaltvorrichtung hinzukommende Reibungswiderstände in seiner Genauigkeit verschlechtert werden könnte, ist auf der Welle 1 eine Spiralfeder 30 angebracht, die beim Einstellen gespannt wird.
PATENT-ANSPRÜCHE : i. Verbrauchsunterbrecher für Elektrizitätszähler mit einer Einstellvorrichtung für den Stromverbrauch, durch welchen der Strom nach Lieferung einer bestimmten Strommenge unterbrochen wird, gekennzeichnet durch eine mittels eines Handschlüssels einstellbare Welle (1), auf der ein vom Zähler angetriebener Kupplungsteil (3) lose und ein das Schaltwerk (6, 10, 11) für den Stromschalter (8) betätigender Kupplungsteil (4) fest angeordnet ist, so dass das Wiedereinstellen zwecks weiterer Stromentnahme in einem beliebigen Zeitpunkt der Stromliefung ermöglicht wird.
<Desc / Clms Page number 1>
Confidence breaker for electricity meters with an adjustment device for the
Power consumption.
EMI1.1
<Desc / Clms Page number 2>
on which the lifting thumb 18 is attached, rotated. When the counter is out of operation and the setting apparatus shows zero (FIGS. I and 2), the switch 8 assumes an inclined position in which it rests on the parallel lifting thumb.
In order to put the counter back into operation, the switch must be put in the final position and the device set to any number of Kw.-hours at the same time. For this purpose, the bolt 14 must first be pushed back so that the lifting thumb 18 is positioned vertically by turning the crank 16. The keyhole 19 has thus become free and the shaft 1 accessible, so that nothing stands in the way of adjustment. After the switch has been brought into the final position, the counter could also register without actuating the setting device.
To prevent this, the dosing lock is arranged so that the key can only be removed when the bolt is in the locked position; a suitable escapement is attached so that the key is not allowed a full turn.
So if the case should arise that intentionally or inadvertently the cam disk 6 remained in the zero position, that is to say the setting device was not actuated, the extension 11 would not protrude up to the switch. To remove the key, the dosing lock has to be locked and the lifting thumb has to be brought back into the inclined position. The switch will now have both supports (extension 11 and lifting thumb 18) missing and the counter will be switched off.
To relieve the counter, the accuracy of which could be impaired by various frictional resistances added by the setting and switching device, a spiral spring 30 is attached to the shaft 1 and is tensioned during setting.
PATENT CLAIMS: i. Consumption interrupter for electricity meters with a setting device for the electricity consumption, by means of which the electricity is interrupted after a certain amount of electricity has been delivered, characterized by a shaft (1) which can be adjusted using a hand key and on which a coupling part (3) driven by the meter is loose and the switching mechanism ( 6, 10, 11) for the current switch (8) actuating coupling part (4) is fixedly arranged, so that it can be reset for the purpose of further current consumption at any point in time of the current supply.