<Desc/Clms Page number 1>
Verfahren zur Gewinnung von Alkalimetall aus seinen Legierungen.
EMI1.1
Vereinigung der Metalle unter sehr starker Wärmeentwicklung statt, so dass man also wohl zu der Annahme berechtigt ist, dass sich hiebei feste Verbindungen nach bestimmten Ver- hältnissen bilden. Bestätigt wird diese Annahme durch das Verhalten der Bleinatriumlegierungen beim Erhitzen über den Siedepunkt des Natriums hinaus, wobei sich herausstellt, dass man nur einen verhältnismässig kleinen Teil des Alkalimetalles al) destillieren kann. Will man alles oder nahezu alles Metall aus der Legierung austreiben, so muss die Temperatur beträchtlich über den Siedepunkt des Natriums erhöht werden und man gelangt alsdann zu solchen thermischen Verhältnissen, dass die Apparatenfrage unlösbare Schwierig- keiten bereitet.
Dieses Verhalten machte es bisher unmöglich, die durch feuerflüssige Elektrolyse billig darstellbare Bleinatriumnlegierung auf Blei und Natrium zu verarbeiten.
Es wurde vorgeschlagen, aus der Bleinatriumlegierung das wertvolle Alkalimetall auf dem Wege der Vakuumdestillation zu gewinnen. Beim weiteren Studium der obwaltenden Verhältnisse wurde nun die überraschende Beobachtung gemacht, dass eine Abtrennung des Natriums auch ohne Vakuumdestillation aus der Bleinatriumlegierung bewirkt werden kann, obwohl, wie bemerkt, in dieser feste Verbindungen nach bestimmten Verhältnissen angenommen werden müssen. Es wurde nämlich festgestellt, dass beim Durchpressen eines zweckmässig auf höhere Temperatur erwärmten, inerten Gasstromes durch die geschmolzene Legierung schon unterhalb des Siedepunktes des metallischen Natriums dieses in einem hohen Prozentsatz und rasch aus der Legierung ausgetrieben wird.
Als zweckmässige Temperatur hat sich mittlere Rotglut erwiesen ; weiterhin ist es sehr förderlich. den Gasstrom unter verhältnismässig starkem Druck durch die Legierung nach der Vorlage zu treiben, und zwar in möglichst weitgehender Verteilung, so dass diese einer schaumförmigen Masse gleicht. Die Stärke dos Druckes richtet sich nach der Hnbe der Metallschicht, die das Gas zu passieren hat.
EMI1.2
zügliche ist, so kann das Destilliergefäss von aussen geheizt werden, dies umsomehr, als man durch Vorwärmung des inerten Gasstromes bereits einen Teil der erforderlichen Wärme zuführen kann.
EMI1.3
den niederzuschlagenden Natriumdämpfen abzukühlen und kühl aus der Vorlage auszutreten.
**WARNUNG** Ende DESC Feld kannt Anfang CLMS uberlappen**.
<Desc / Clms Page number 1>
Process for the extraction of alkali metal from its alloys.
EMI1.1
Combination of the metals takes place under very strong heat development, so that one is therefore probably justified in assuming that fixed connections are formed here according to certain proportions. This assumption is confirmed by the behavior of the lead sodium alloys when heated above the boiling point of sodium, whereby it turns out that only a relatively small part of the alkali metal al) can be distilled. If one wants to drive out all or almost all of the metal from the alloy, the temperature must be raised considerably above the boiling point of sodium, and one then arrives at such thermal conditions that the question of the apparatus causes insoluble difficulties.
This behavior has hitherto made it impossible to process the lead-sodium alloy, which can be produced cheaply by hot-melt electrolysis, on lead and sodium.
It has been proposed to extract the valuable alkali metal from the lead-sodium alloy by vacuum distillation. Upon further study of the prevailing conditions, the surprising observation was made that the sodium can also be separated from the lead-sodium alloy without vacuum distillation, although, as noted, solid compounds must be assumed in this according to certain conditions. It has been found that when an inert gas stream, suitably heated to a higher temperature, is forced through the molten alloy below the boiling point of the metallic sodium, a high percentage of this is expelled quickly from the alloy.
Medium red heat has proven to be an appropriate temperature; it is also very beneficial. to drive the gas stream under relatively strong pressure through the alloy after the template, and in the greatest possible distribution so that it resembles a foam-like mass. The strength of the pressure depends on the depth of the metal layer through which the gas has to pass.
EMI1.2
The still can be heated from the outside, all the more so as part of the required heat can already be supplied by preheating the inert gas stream.
EMI1.3
to cool down the sodium vapors to be precipitated and to leave the template cool.
** WARNING ** End of DESC field may overlap beginning of CLMS **.