Journal of Petroleum Technology and Alternative Fuels Vol. 4(3), pp. 30-43, March 2013
Available online at http://www.academicjournals.org/JPTAF
DOI: 10.5897/JPTAF12.026
©2013 Academic Journals
Review
Waste oils as alternative fuel for diesel engine:
A review
K. Naima* and A. Liazid
Research Laboratory LTE-ENSET, B. P. 1523 El Mnaouer 31000-Oran, Algeria.
Accepted 7 February, 2013
Increase in energy demand, stringent emission norms and depletion of oil resources have led the
researchers to find alternative fuels for internal combustion engines. On the other hand, waste oils
pose a very serious environment challenge because of their disposal problems all over the world. In
this context, waste oils are currently receiving renewed interest. The properties of the oil derived from
waste plastics, cooking and engines oils were analyzed and compared with the petroleum products and
found that it has properties similar to that of diesel. This paper gives a brief review about using waste
oil of these three types of oil as a fuel for diesel engines. The conversion process of each type of waste
oil is presented. The results obtained from the experimental studies on a diesel engine are discussed.
Key words: Waste oil, cooking, plastic, conversion, fuel, engine.
INTRODUCTION
The threat posed by climate change and the striving for
security of energy supply is issues high on the political
agenda these days. Governments are putting strategic
plans in motion to decrease primary energy use, take
carbon out of fuels and facilitate modal shifts (Sebastian
and Thomas, 2009). Throughout the world, many steps
are being taken to alternate petroleum based fuel due to
tires from automotive vehicles, restaurant and plastic
have become increasingly hard. Waste management is
the impact of increase in oil price and the reality of
petroleum depletion. Additionally, the disposals of waste
*Corresponding author. E-mail: n_khatir@hotmail.com. Tel: 213
779 104 753.
Abbreviation: ATDC, Before top died centre; Bsfc, break
specific fuel consumption; Bmep, break mean effective
pressure; CA, Crank angle; DF, diesel fuel; DLF, diesel-like
fuel; FFA, free fatty acid; GLF, gasoline-like fuel; PM,
particulate matter; Rpm, revolution per minute; SI, spark
ignition; THC, total hydrocarbons; UCO, used cooking oil; WPO,
waste plastic oil; WCO, waste cooking oil; WEO, waste engine
oil; WEO100, pure (100%) waste engine oil; WEO75, mixture of
75% WEO and 25% diesel fuel; WEO50, mixture of 50% WEO
and 50% diesel fuel.
once a technical problem that has to be solved under
thrifty, yet environmentally acceptable and hygienic
conditions and preferably performed by skilled labor.
Disposal of waste vehicle tires is one of the most
important problems that should be solved. It is estimated
that worldwide, over one billion waste tires are generated
annually (Cumali and Hüseyin, 2011). Industrial and
household wastes are produced on a daily basis and are
managed in many ways, depending on their type.
According to their combustibility, wastes are basically
categorized as either burnable or unburnable. The
burnable wastes are normally treated by combustion with
or without heat production, while the unburnable wastes
are treated by recycling, re-use, or landfilling, depending
on the material. Municipal and industrial wastes that
contain high heat value, such as waste plastics oil
(WPO), waste cooking oil (WCO), and waste lubricating
oil (WLO) are considered efficient feedstocks for energy
production in a Waste-to-Energy regimen (Ampaitepin
and Tetsuo, 2010). The main objective of this paper is to
analyze by means of literature review the engine
performance, combustion and emission characteristics of
diesel engines fuelled with biodiesel produced from waste
engine, waste cooking and waste plastic oil and/or its
blends with petroleum-based diesel fuel.
Naima and Liazid
WASTE OIL AS FUEL FOR DIESEL ENGINES
Waste engine oil
Waste lubricant oils and biofuels are two important
alternative fuel sources proved to be the best substitutes
for existing petrofuels, since waste generated oils
represent more than 60% of used lubricant oils.
Therefore, waste oils are one of the most abundant
pollutant residues that are generated nowadays, reaching
the value of 24 million metric tonnes per year (Fuentes et
al., 2007). In recent years, recycling of the waste
lubricant oils and utilizing of the products as fuels have
become important topics for researchers. Most of the
lubricant oils are generally obtained from petroleum
resources. Petroleum-derived base oils currently account
for about 97% of the total lubricant production (Bhaskar
et al., 2004). However, these oils become waste oils
harmful for environment after a certain time period.
Recycling of the waste lubricant oils by purifying and
converting them into fuels is very important in terms of
protection of the environment. After waste lubricant oils
are converted into fuels, they can be used as fuels in
internal combustion engines. In recycling process, waste
lubricant oils are exposed to various processes, and then
used as fuel or they are converted into various chemicals
in order to minimize the harmful effects of these wastes
(Bhaskar et al., 2004).
Millions of tons of used oils are disposed through
dumping on the ground or in water, land filling, or nonenergy-recovery (Bhaskar et al., 2004). The used or
waste oils can be refined and treated to produce fuels or
lubricating oil base stock. On the other hand, the waste
oils pose an environmental hazard due to both their metal
content and other contaminants (Nerin et al., 2000). The
high-volume waste oils can be turned into valuable fuel
products by refining and treating processes. Converting
of the waste oils into diesel and gasoline-like fuels to be
used in engines without disposing is very important.
Utilization of the diesel and gasoline-like fuels produced
from the waste lubricant oils, and blending of the
produced fuels with gasoline or turpentine decrease
consumption of petroleum based fuels, protecting
environment from toxic and hazardous chemicals
(Bhaskar et al., 2004). It also saves of foreign exchange,
reduces greenhouse gas emissions and enhances
regional development especially in developing countries
(Demirbas and Demirbas, 2007).
Characteristics of any fuel are very important from the
point of deciding whether the fuel can be used for desired
application or not. Therefore, some characteristics of the
produced diesel-like fuel and gasoline-like fuel are shown
in Tables 1 and 2, respectively, together with standard
values of a diesel and gasoline fuel. The table shows that
some of the parameters of density, boiling point,
viscosity, flash point and lower heating value are in the
standard values of the diesel oil or reasonably close to
31
the standard values. But, sulfur amount is considerably
higher than that value. It should be decreased below the
value of 50 ppm.
Waste cooking oil
Many researchers have tried to develop vegetable oilbased derivatives that approximate the properties and
performance of petroleum-based diesel fuel. Esters of
fatty acids (biodiesel), derived from the transesterification
of vegetable oils have properties similar to petroleumbased diesel fuel (Enweremadu and Rutto, 2010).
Literature is replete with advantages derived using
biodiesel: it helps to reduce the carbon dioxide emission
to the atmosphere, it is renewable in nature and safer to
handle, it has no aromatic compounds, practically no
sulphur content, and oxygen atoms in the molecule of
fuel may reduce the emissions of carbon monoxide (CO),
total hydrocarbon (THC) and particulate matter (PM)
(Lapuerta et al., 2002; Alamu et al., 2008). However,
biodiesel is known to have some drawbacks when
compared with petroleum-based diesel fuel such as
worse low temperature properties, greater emissions of
some oxygenated hydrocarbons, higher specific fuel
consumption, decrease in brake thermal efficiency and
higher production cost (Dunn et al., 1996; Canakci and
Van-Gerpen 2001). The problem of production cost has
been partially solved by the use of waste cooking or
animal fats as the raw materials in the transesterification
process (Dorado et al., 2003, 2004).
However, during frying, vegetable oil undergoes
various physical and chemical changes, and many
undesirable compounds are formed. These include free
fatty acid and some polymerized triglycerides which
increase the molecular mass and reduce the volatility of
the oil. Therefore, fatty acid esters obtained from frying oil
influences the fuel characteristics (such as the viscosity
and it is believed that the burning characteristics reduce)
leading to a greater amount of Conradson carbon residue
(Kulkarni and Dalai, 2006). Comprehensive reviews on
biodiesel production from used cooking oil (UCO) can be
found in (Kulkarni and Dalai, 2006; Enweremadu and
Mbarawa, 2009). Table 3 shows a comparison of fuel
properties for a WCO biodiesel and diesel fuel.
Currently, compared to petroleum-based diesel, the
high cost of biodiesel is a major barrier to its
commercialization. It is reported that approximately 7085% of the total biodiesel production cost arises from the
cost of raw material. Use of low-cost feedstock such as
WCO should help make biodiesel competitive in price
with petroleum diesel. Numerous studies have been
conducted on biodiesel production and emission testing
in the past two decades. Most of the current challenges
are targeted to reduce its production cost, as the cost of
biodiesel is still higher than its petro-diesel counterpart.
This opens a golden opportunity for the use of WCO as
32
J. Pet. Technol. Altern. Fuels
Table 1. Comparison of diesel-like fuel obtained from waste lubrication oil and diesel fuel
(Arpa et al., 2010a).
Properties
Density at 15°C (kg/m3)
2
Viscosity at 40°C (mm /s)
Flash point (°C)
Sulfur (ppm)
Water (mg/kg)
Lower heating value (kJ/kg)
Temperature at 250°C, max. volume (%v/v)
Temperature at 250°C, min. volume (%v/v)
Volume at 95%, max. temperature (°C)
Diesel fuel
820-845
2-4.5
>55
50
<200
42.700
65
85
360
DLF
818
3.49
57
3500
130
42.500
20
90
360
Table 2. Comparison of gasoline-like fuel obtained from waste lubrication oil and diesel fuel
(Arpa et al., 2010b).
Properties
3
Density at 15°C (kg/m )
Flash point (°C)
Lower heating value (kJ/kg)
Distillation range (°C)
IBP (initial boiling points)
10 vol.%
50 vol.%
90 vol.%
End point
GLF
740
25
43.000
Unleaded gasoline
780
-43
43.890
38
68
126
223
262
34
53
92
154
218
Table 3. Comparison of fuel properties for a WCO and diesel fuel (Enweremadu et al., 2010).
Characteristics
3
Density at 40°C (kg/m )
Specific gravity at 15.5°C
Distillation temperature
10% recovery temperature
50% recovery temperature
90% recovery temperature
Flash point (°C)
Fire point (°C)
2
Kinematic Viscosity at 40°C (mm /s)
Calorific value (kJ/kg)
A.P.I gravity
Cetane index
Aniline point (°C)
its production feedstock. Everywhere in the world, there
is an enormous amount of waste lipids generated from
restaurants, food processing industries and fast food
shops everyday (Xiangmei et al., 2008). In China, with
annual consumption of edible oils approaching 22 million
tons, the country generates more than 4.5 million tons of
Waste cooking oil
876.08
0.893
Diesel
807.3
0.825
340
345
320
160
164
3.658
39767.23
26.87
50.54
NA
165
265
346
53
58
1.81
42347.94
39.51
46.21
77.5
used oil and grease each year, roughly half of which
could be collected through the establishment of an
integrated collection and recycling system. Those 2
million tons of “ditch oil” alone would guarantee the
smooth operation of all current biodiesel production lines.
Reusing of these waste greases cannot only reduce the
Naima and Liazid
33
Table 4. Comparison of fuel properties from waste plastic oil and diesel fuel (Mani et al., 2009).
Property
Density at 30°C in gm/cc
Ash content, %
Gross calorific value (kJ/jg)
Kinematic viscosity. Cst at 40°C
Cetane number
Flash point, °C
Fire point, °C
Carbone residus, %
Sulphur content, %
Distillation temperature, °C at 58%
Distillation temperature, °C at 95%
burden of the government in disposing the waste,
maintaining public sewers and treating the oily
wastewater, but also lower the production cost of
biodiesel significantly. Furthermore, biodiesel fuel has
been demonstrated to be successfully produced from
waste edible oils by an alkali-catalyzed transesterification
process (Mittelbach and Gangl, 2001; Al-Widyan and AlShyoukh, 2001a, b), and can be considered as
alternative fuels in diesel engines and other utilities
(Dorado et al., 2003, 2004; Al-Widyan and Al-Shyoukh,
2002a, b).
Waste plastic oil
The last 30 years have witnessed an explosive growth of
the plastic industry. The production of synthetic polymers
represented by polyethylene (PE), polypropylene (PP),
polystyrene (PS), and polyvinyl chloride (PVC) worldwide
has increased more than 100 times in the last three
decades. These plastics are widely used in many
important day to day applications such as clothing,
household appliances and in automotive products and
aerospace. While we enjoy the conveniences that
plastics can provide, the treatment of waste plastics
becomes an unavoidable and imminent issue. In this
regard, it can be safely stated that we are in urgent need
and effective ways to recycle waste plastics. Recently
new ways of environmentally-friendly waste plastic
recycling have been of interest, and among them, the use
of waste plastics as a supplemental fuel with coal in the
steel making industry has attracted interest (Mitsuhara et
al., 2001). Attention is also focused on using oil derived
from waste plastics in diesel engines. Diesel engines are
the most preferred power plants due to their excellent
driveability and higher thermal efficiency (Williams and
Williams, 1990).
Plastics are non-biodegradable polymers mostly
containing carbon, hydrogen and few other elements.
According to a nationwide survey conducted in India in
Waste plastic oil
0.8355
0.00023
44.340
2.52
51
42
45
82.49
0.030
344
362
Diesel
0.840
0.045
46.500
2.0
55
50
56
26
0.045
328
340
the year 2000 approximately 6000 tonnes of plastic
wastes were generated every day, and only 60% of it was
recycled. In India alone, the demand for plastics is about
8 million tonnes per year. More than 10,000 metric
tonnes/ day are produced in India and balance is
imported from other countries. Most of the plastics are
recycled and sometimes it is not done so due to lack of
sufficient market value. Of the waste plastics not recycled
about 43% is polyethylene and most of them is in the
form of containers and packaging materials (Mani and
Nagarajan, 2009b).
The extent of conversion of plastics or plastic derived
waxes into light engine fuels can be increased by the
application of stable hydro cracking catalysts. Similar to
petroleum derived cracking products, the fractions from
plastics processing contain appreciable quantities of
aromatics and unsaturated hydrocarbons (Hai et al.,
2001). Some of the properties and characteristics of
waste plastic oil and diesel are compared in Table 4.
Because of the olefin content, it would be reasonable to
submit the derived fractions to the hydrogenation step,
typical of pyrolysis or cracking gasoline hydro refining
process. Similarly, because of large quantity of linear nparaffinic hydrocarbons it would be profitable to isomerise
them in order to lower cloud and freezing points. The
results showed that waste plastic disposal oil when mixed
with heavy oils reduces the viscosity significantly and
improves the engine performance (Soloiu et al., 2000).
However, very little work has been done to test their use
in high-speed diesel engines.
CONVERSION PROCESS
Conversion of waste engine oil
The high-volume waste oils can be turned into valuable
fuel products by refining and treating processes.
Converting of the waste oils into diesel and gasoline-like
fuels to be used in engines without disposing is very
34
J. Pet. Technol. Altern. Fuels
Figure 1. Schematic diagram of the purified and distillation system.
important (Arpa et al., 2010a, b). Utilization of the diesel
and gasoline-like fuels produced from the waste lubricant
oils, and blending of the produced fuels with gasoline or
turpentine decrease consumption of petroleum based
fuels, protecting environment from toxic and hazardous
chemicals (Bhaskar et al., 2004). It also saves of foreign
exchange, reduces greenhouse gas emissions and
enhances regional development especially in developing
countries (Demirbas and Demirbas, 2007). The
turpentine is a biofuel obtained from the volatile fraction
of resin extracted from pine trees. It has several
advantages such as: a) it is a renewable and
environmentally friendly alternative liquid fuel; b) its
heating value and viscosity are higher than those of
gasoline (Yumrutas et al., 2008; Karthikeyan and
Mahalakshmi, 2007a, b); c) it can be used in any spark
ignition (SI) engines as an additive to the gasoline
(Yumrutas et al., 2008) or gasoline-like fuel (GLF); d) its
self-ignition and boiling temperatures are higher than
those of gasoline (Yumrutas et al., 2008; Karthikeyan and
Mahalakshmi, 2007a, b). It can be produced from plentiful
domestic cellulosic biomass resources such as woody
plants, agricultural and forestry residues, and a large
portion of municipal solid waste and industrial waste
streams. It was used in early engines without any
modification.
However, abundant availability of petrofuels stopped
the usage of turpentine in internal combustion engines.
Increasing cost of petrofuel prevailing today reopens the
utility of turpentine in the internal combustion engines
(Karthikeyan and Mahalakshmi, 2007a, b).
In the study of Arpa et al. (2010a, b) the authors used a
recycling system for the waste lubricant oil. A recycling
system was designed and manufactured in industry to
purify waste oil from dust, small carbon soot and metal
particulates, and reutilize the waste oil. Schematic
representations and picture of the system are shown in
Figure 1. In the recycling system, two fuels to be used in
engines were produced by applying pyrolitic distillation.
The fuels named as gasoline-like fuel (GLF) and diesellike fuel (DLF) were obtained from waste lubrication
engine oil. The oil was collected from gasoline and diesel
engines. The recycling system was consisted of waste oil
and produced fuel storage tank, pump, filter, a reactor,
heaters, mixer, condenser and control unit. The waste
lubricant engine oil was collected and stored in the
storage tank. The oil pump was used to transfer waste oil
in the storage tank to metallic filter. The waste oil was
taken by the pump from the storage tank, and it was
filtered using a quality filter with 20 mm mesh size to
purify it from heavy metal particles, carbon soot, gumtype materials and other impurities. After removing the
purified oil from the filter, it was flowed into the reactor.
The reactor is the most important part of the recycling
system, since pyrolitic distillation or thermal treatment of
the waste oil is performed in the reactor. It has a
cylindrical shape with dimensions of 30 cm in diameter
and 40 cm in height. It has a capacity that will be able to
produce 20 L of fuel. This volume is enough to do all
tests, which include characteristics of the fuel,
performance and emissions. The reactor was isolated
with glass wool with a thickness of 5 cm to minimize heat
Naima and Liazid
loss from the reactor. It includes a mixer and electrical
heaters. The mixer was used to blend the oil and additive
to obtain uniform blend and temperature in the oil. The
heaters were used to heat the mixture of the purified oil
and additive in order to make thermal destruction more
easily. The heaters with a total heating capacity of 5 kW
were placed around the reactor container. They can be
capable of heating the mixture up to 600°C. They were
controlled by a controlling unit adjusting heating rate.
Then, the reactor was used as a heater of a distillation
unit, and fuel sample produced from the waste lubricant
oil in the reactor was distilled. The distillation unit was
named as condenser, which is shown on Figure 1. After
being condensed of the fuel sample was collected in the
fuel storage tank. In the recycling system, 80 wt. % of the
total, waste lubrication oil was converted into useful fuel
in the pyrolysis process. Remaining parts such as
impurities smaller than 20 mm, sludge and solid additives
in the reactor were named as residue. It was about 20 wt.
%, and was rejected from the reactor. It is necessary to
purify the waste oil to produce a valuable fuel.
Therefore, it was taken from the tank by the oil pump,
and was flowed through the filters having 20 m mesh
sizes. It was separated from dust, carbon soot, metal and
other particles, and then charged to the reactor. The oil
was heated up to 330°C in the reactor, in which the
pyrolysis process occurred, and it was treated for 1 h at
this temperature. During the process, the mixer in the
reactor mixed the oil-additive mixture. Heating process
was continued by increasing the reactor temperature with
electronic control unit in order to pass to the distillation
process after the pyrolysis process. The vaporized fuel
due to heating process was condensed through
condenser in which water was used as cooling fluid. After
the fuel become liquid, it was stored in fuel storage tank.
Properties and distillation of the produced fuel should be
tested to determine whether it can be used in a diesel
engine or not, and they should also be compared with the
diesel fuel commonly used in diesel engines (Table 1).
The produced fuel was segregated into light and heavy
fuels according to characteristics and distillation test
results, since some amount of the produced fuel was
lighter than diesel fuel. That is why it was necessary to
segregate the light fuel from the heavy fuel to eliminate
detrimental effects of these fuels on an engine.
Conversion process of waste cooking oil
The conversion process presented in this section is the
work of Xiangmei et al. (2008). The WCO was obtained
from Restaurants. Every day this restaurant produces
many WCO which used for frying beefsteak, French
chips. So the WCO contain some food particles,
phospholipids, grease and wax etc. WCO sample heated
and filtered under vacuum to remove any different solid
impurities. Then 40% phosphate acid washing and
35
distillated water washing were adopted to eliminate
phospholipids. And in order to avoid saponification
reaction for high free fatty acid (FFA) content, the FFA
was esterified with methanol by sulfuric acid. When the
FFA content was lower than 1.0%, the sulfuric acid was
drained and the sodium hydroxide was introduced into
the system to complete the transesterification.
Transesterification method was used for methyl ester
production from waste frying oil. This method is a
chemical reaction, which refers to the conversion of an
organic acid ester into another ester of the same acid socalled biodiesel using an alcohol in presence of a
catalyst. The method depends on several basic variables,
namely, reaction temperature, alcohol and catalyst type.
In this study per liter, waste frying oil requires 200 ml
methyl alcohol, 6.5-8.5 g NaOH that is determined with
titration, and 1-2 g acetic acid. In the first stage, test
applied the transesterification reaction is realized in the
reactor tank at 651°C temperature during 1 h.
The second stage is composed of product rest and raw
biodiesel separation from glycerin, then, washing process
of obtained raw biodiesel is done by using the same
volume of pure water, and second washing process
follows and this washing process is carried out to
increase the pellucidity of biodiesel by using bubble
method. Lastly, water is separated from all products by
evaporation with heating process (Zafer and Mevlüt,
2008) (Figure 2).
Conversion process of waste plastic oil
Pyrolysis
The technologies for WP recycling are grouped into three
main categories: (1) material recycling, (2) chemical
recycling, and (3) thermal recycling (or energy recovery).
The primary and secondary recycling described above
are considered material recycling; tertiary and quaternary
recycling have the same meanings as chemical recycling
and thermal recycling, respectively. Therefore, pyrolysis
of plastics is considered tertiary recycling, which
transforms the plastic polymers into their basic
monomers or hydrocarbon (Lapuerta et al., 2002). The
pyrolysis by direct heating (Figure 3) was adopted to
produce the paraffin and crude oil from the plastic wastes
in the 1990s. The pyrolysis process involves the break
down of large molecules to smaller molecules. Produces
hydrocarbons with small molecular mass (e.g. ethane)
that can be separated by fractional distillation and used
as fuels and chemicals. This process gives on weight
basis 75% of liquid hydrocarbon, which is a mixture of
petrol, diesel and kerosene, 5 to 10% residual coke and
the rest is LPG (Mani and Nagarajan, 2009b).
The small-scaled process is featured by facilitation,
convenience and low equipment investment. The system
consists of feed-supply, pyrolysis reactor, fractionating
tower, heating and temperature controller and device for
36
J. Pet. Technol. Altern. Fuels
Figure 2. Schematic representation of biodiesel production system from waste frying oil.
Figure 3. Pyrolysis-catalytic upgrades technique of plastic wastes.
Naima and Liazid
filling the plastics into the pyrolysis reactor. The capacity
of this pilot plant is 1000 tonnes/annum. However, the
temperature caused by pyrolysis is higher and all the
reactive time is longer than the other methods else. The
octane number of gasoline gained is relatively low and
the pour point of diesel oil is high. More paraffin is
produced in the process of pyrolysis. Although this
process is simple and convenient, the converting rate and
yield is still lower (Guang-Hua et al., 2007).
The pyrolysis rate and yield should be promoted by a
catalyst, like silica–alumina catalyst or diatomite, etc (Liu
and Chen, 2001). Before the catalyst and plastic waste is
mixed within the pyrolysis reactor, the plastic waste must
be cleaned. The total yield of fuel oil is 50–65%, relying
on the composition of plastic waste during pyrolysis. But,
one problem is how to recycle the catalyst, carbon and
other residua after pyrolysis. This process is also called
the catalytic pyrolysis. The other problem for this process
is the pyrolysis equipment’s corrosion incurred by
polyvinyl chloride (PVC) in mixed plastic wastes.
Therefore, it is strongly recommended to establish a
reasonable sorting system and apply a efficient technique
to eliminate hydrochloric acid (Guang et al., 2007; Jerzy,
2002).
Pyrolysis-catalytic upgrade
Since the total yield of fuel oil with pyrolysis is still lower
and the quality of oil is not satisfied as gasoline and
diesel oil, the upgrade by catalyst for the crude products
gained with pyrolysis can be used. Having improved the
quality of finished oil, this process has been widely used
in many factories (Li et al., 2002). Figure 4 shows the
flowchart of pyrolysis-catalytic upgrade, which has been
adopted in factories to treat the mixed plastic wastes. The
system consists of the knapper, extrusion machine,
pyrolysis reactor, catalytic upgrade reactor, fractionating
tower, heating and temperature controller, separator of oil
and water, and oilcan. The factory nearby Beijing used it
to produce the fuel oil. The finished oil consists of
gasoline (60%) and diesel oil (40%). The total yield
reaches as high as 72.5% (Wang et al., 2003).
According to the yield of converting waste plastics to oil
in China, the plastic wastes weighing 1.92 tonnes can
produce 1 tonne of fuel oil. A plant with a capacity of 3
tonnes/day will need 1728 tonnes of plastic wastes
annually. Supposing the average content of plastic
wastes is that the municipal solid wastes account for
about 0.5% for cities and 0.3% for countryside, the
economic transportation distance will be within 200 km or
so. As the economic support from local government is
short, and the whole process from collecting,
transporting, sorting to converting must be in accordance
with marketing rule, the plant has to face towards a big
risk in converting plastic wastes to fuel oil (Guang et al.,
2007).
37
RESULTS OF USING WASTE OILS AS FUEL IN
DIESEL ENGINES
Results obtained from waste cooking oil
Effect on performances
Studies demonstrate that WCO and its blends has a
lower ignition delay (Enweremadu and Rutto, 2010; Rao
et al., 2008; Sinha and Agarwal, 2005). A possible
explanation for lower ignition delay periods of WCO and it
blends with increase in the percentage of WCO might be
due to higher octane number of WCO and its blends
compared to diesel. Another possible explanation may be
the presence of oxygen present in WCO and the splitting
of higher molecules of WCO such as oleic and linoleic
fatty acid methyl esters into lower molecules of volatile
compounds during injection which advances the start of
combustion causing earlier ignition. The reduction in
ignition delay with increase in load might be as a result of
higher combustion chamber wall temperature at the time
of injection and reduced exhaust gas dilution
(Enweremadu and Rutto, 2010).
The peak pressure of WCO fuel and its blends is higher
than that of diesel fuel (Enweremadu and Rutto, 2010;
Rao et al., 2008; Sinha and Agarwal, 2005). C. C.
Enweremadu gives three reasons of this: The reduction
in ignition delay with increase in percentage of WCO
which results in earlier combustion might lead to the
slightly higher peak pressures. Another possible
explanation of this may be the higher oxygen content of
WCO which favors better combustion. Also since WCO
has lower calorific value, a large amount of fuel needs to
be burned in premixed combustion stage and this may
result in slightly higher peak pressure (Enweremadu and
Rutto, 2010).
A detailed study on the effects of the percentage of
used cooking oil methyl ester (WCO) on combustion
characteristics (ignition delay, rate of pressure rise, peak
pressure, heat release) has been undertaken (Rao et al.,
2008) heat release of WCO and its blends were
compared with that of diesel, the maximum heat release
rate of 71.459 J/°CA was recorded for diesel at 68 BTDC,
while WCO records 51.481 J/°CA at 88 BTDC. The
results show that the maximum heat release rate
decreases with increase in percentage of WCO in the
blend. It can also be observed that maximum heat
release rate occurs earlier with the increase in the
percentage of WCO in the blend. The observations made
for the rate of heat release may also be attributed to the
reduction in ignition delay of WCO and its diesel blends
and can be explained in a similar manner as the rate of
pressure rise. Also, lower calorific value of WCO and its
blends may contribute to lower heat release (Sinha and
Agarwal, 2005). It is also possible that an increase in the
oxygen fraction of the injected fuel provides an increase
in the maximum heat release rate and in the fraction of
38
J. Pet. Technol. Altern. Fuels
Figure 4. Flowchart of pyrolysis-catalytic upgrade (Pyrolysis equipment for mixure
of plastic wase (1) Pyrolysis reactor; (2) Stirrer; (3) Motor; (4) Pipe; (5) Heavy oil
separator; (6) Oil tank.
fuel burned in the premixed combustion phase; this case
is more obvious at a high engine speed (Enweremadu
and Rutto, 2010).
Effect on emissions
A relatively high disparity of results has been found
regarding the emissions characteristics of used cooking
oil biodiesel and/or its blends. Although, a dominant trend
has been found in most cases, there have always been
opposing trends proposed elsewhere by contrast. The
precise features of the engines tested and their operating
conditions, the different biodiesel fuels used, their
characteristics, qualities and blends, measurement
techniques and procedures, and instrumentations have a
strong influence on the impact of WCO biodiesel hence,
each study was specific (Enweremadu and Rutto, 2010).
Ulusoy and Tekin (2004) investigated the effects of
biodiesel made from used frying oil on emissions in a Fiat
Doblo 1.9 DS, four cylinder, four-stroke, and 46 kW
power capacity diesel engine. Comparative measurements with diesel fuel were conducted on emission
characteristics of each of the fuel used. According to
emission tests, as a result of biodiesel consumption, a
reduction of 8.59% in CO emission while an increase of
2.62 and 5.03% were observed in CO2 emission and NOx
emission, respectively. On the other hand, HC emissions
and PM emissions decreased by 30.66 and 63.33%,
respectively. It was concluded that these engine emission
tests show that biodiesel is a more environment friendly
fuel than diesel fuel.
Exhaust emission characteristics were evaluated in a
Toyota van, powered by a 2 L indirect injection naturally
aspirated diesel engine, operating on a vegetable-based
waste cooking oil methyl ester by Gonzalez-Gomez et al.
(2000). Tests were conducted on a chassis dynamometer
and the data were compared with previous results
conducted on the same vehicle using mineral diesel fuel.
The data obtained included smoke opacity, CO, CO2, O2,
NO, NO2 and SO2. These data showed that waste
cooking oil methyl ester developed a significant lower
smoke opacity level and reduced CO, CO2, SO2
emissions. However, NO2, NO, and O2 levels were higher
with the waste vegetable oil based fuel (Gonzalez-Gomez
et al., 2000).
The engine and road performance tests of biodiesel
fuel derived from used cooking oil were evaluated in a
Renault Mégane automobile and 75 kW Renault Mégane
diesel engine in winter conditions for 7500 km road rests,
and the results were compared with those using diesel
fuel (Etinkaya et al., 2005). Results showed that the
emission characteristics of biodiesel fuel produced from
hazelnut soapstock/waste sunflower oil mixture and its
blend with diesel fuel was investigated by Usta et al.
(2005). The study showed that at full load, the CO
emissions of the blend were higher at low speed and
lower at high speeds than those of diesel fuel, while the
blend resulted in higher CO2 emissions in the
experimental range. At partial loads, it was found that the
blend did not cause significant changes in the CO and
CO2 emissions. There was a significant SO2 reduction
with the blends due to lower sulphur content of the
biodiesel. NOx emissions slightly increased due to the
higher combustion temperature and the presence of fuel
oxygen with the blend at full load. However, the
increasing amount of NOx emission slowed down with
decreasing load. Most of the literature reviewed showed
(Gonzalez-Gomez et al., 2000; Etinkaya et al., 2005;
Usta et al., 2005) that there was a slight increase in NOx
emissions when using WCO biodiesel. However, some
other works found that NOx increased only under certain
operating conditions such as test conditions, load
conditions, alcohol-base of ester (methyl, ethyl) and the
Naima and Liazid
effect of WCO in the blends. While some works found
reduction in NOx emissions when using WCO and its
blends, other works did not find any differences in the
NOx emissions between WCO and/or its blends and
fossil diesel. Various reasons have been given for the
increase in NOx emissions when using biodiesel and/or
its blends. NOx emission is primarily a function of
pressure, temperature and total oxygen concentration
inside the combustion chamber. One argument is that the
increases in NOx emissions obtained are in proportion to
the concentration in biodiesel (Schumacher et al., 1994).
It is has been argued that the increase in NOx emissions
with increase in the percentage of WCO in the blend
maybe associated with the increased oxygen content of
WCO. Invariably all biodiesel have some level of oxygen
bound to its chemical structures. Hence, oxygen
concentration in WCO biodiesel fuel might have
influenced the NOx formation.
Results obtained from waste engine oil
Effect on performances
Arpa et al. (2010a) conducted an experimental study on
diesel-like fuel (DLF) on engine performance and exhaust
emission. It is observed from the test results that about
60 cc out of each 100 cc of the waste oil are converted
into the DLF. It is observed that the produced DLF can be
used in diesel engines without any problem in terms of
engine performance. The DLF increases torque, brake
mean effective pressure, brake thermal efficiency and
decreases brake specific fuel consumption of the engine
for full power of operation.
The author found that T, Bmep, thermal efficiency and
Bsfc trends for the DLF and diesel fuel are similar in
nature. It is known that T and Bmep are directly
proportional but Bsfc is indirectly proportional with the
engine brake power given. The T, Bmep, and thermal
efficiency values obtained for the DLF are slightly higher
than those obtained for diesel fuel, but Bsfc is lower in all
revolutions. Average increases of the T and Bmep values
are approximately 0.69% for the DLF. This was due to
high distillation temperature of the DLF than diesel fuel.
In internal combustion engines, the T increases to a
maximum point with the increase of engine speed. After
that critical point, generally the torque decreases step by
step (Mani and Nagarajan, 2009b). The maximum T and
Bmep values obtained from the measured data for the
DLF and diesel fuel in 2000 rpm are 33.86 and 33.71 Nm,
1048.21 and 1043.38 kPa, respectively. The
corresponding thermal efficiency and Bsfc for the same
fuels and the engine speed are 40.68 and 37.88%,
213.23 and 224.52 g/kWh respectively. After the
maximum and minimum values of these parameters they
decrease and increase with the engine speed gradually
(Arpa et al., 2010a, b).
39
Cumali and Hüseyin (2011) conducted an experimental
study on an alternative fuel performed by pyrolysis of
waste vehicle tires. The authors used a pure DF and pure
WEO and a mixture of them with different fractions. He
found that power values of all fuel blends of WEO and
diesel fuels showed increasing trends with respect to
increase in engine speed. However, increases of power
values have no linearity due to the increase in
mechanical losses, especially in higher engine speeds.
Power values of diesel operation were highest among all
the test fuels. The higher the WEO amount blended in the
fuel the lower the power of the engine at the
corresponding condition of engine run. Namely, the
lowest engine power values were obtained for the
WEO100 fuel then for the WEO75 and WEO75 fuels,
respectively. The reductions of power values of WEO and
WEO blend fuels can be attributed to slightly lower
calorific value of the WEO fuel. However, the differences
in power values of test fuels were low at lower engine
speeds. Especially, at the 1500 rpm of engine speed the
power obtained for all test fuels was quite similar.
It is expected that the Bsfc should decrease when the
brake power increases up to engine speed of 2200 rpm.
At high speeds, friction, heat loses and deteriorating
combustion increase Bsfc (Arpa et al., 2010a)
performance parameters for the DGL are similar to those
of diesel and are parallel to them in a regular way. Arpa
found that the torque, Bmep, and thermal efficiency for
the DLF ishigher than those of diesel while the Bsfc for
the DLF is lower than that of diesel. This is an important
criterion that makes the DLF advantageous.
Characteristics and distilled temperatures of fuels are
the other effects on the performance parameters (Koç et
al., 2009). The characteristics give better mixing and
combustion characteristics of the fuels, which cause
reduction in heat loss. It was also emphasized that higher
distilled temperature gives better performance (Al-Ghouti
et al., 2008; Koç et al., 2009). The distillation temperature
make it possible to explain these differences in
performance parameters. Diesel fuel is lighter than the
DLF. Distillation temperatures of the DLF are higher than
those of the diesel fuel up to 80 cc of 100 cc volume. This
indicates that DF is a more volatile fuel than the fuel
obtained from waste engine oil. High volatility decreases
volumetric efficiency and cause vapor lock on hot climate
conditions (48). When low volatile fuels or fuels distilled
at higher temperatures are burned in combustion
chamber of engine gradually, temperature and pressure
in the combustion chamber will increase, which improves
performance parameters of the engine (Al-Ghouti et al.,
2008; Koç et al., 2009). As a result, ignition timing, air–
fuel
ratio, characteristics and higher
distilled
temperatures for the DLF give slightly better performance
parameters than the diesel fuel. Therefore, T, Bmep and
thermal efficiency increase and Bsfc decreases. Test
results from the study have clearly shown that the DLF
has a positive effect on the performance parameters of
40
J. Pet. Technol. Altern. Fuels
the engine, and it can be used as a fuel in the gasoline
engine without any problems.
Cumali and Hüseyin (2011) found that the lowest
torque values were obtained for WEO100, WEO75 and
WEO50 fuels, respectively. The main reason of torque
reduction is considered to be the slightly lower calorific
value of the WEO fuel. Therefore, the reduction in the
torque values of the WEO blends were linear with the
WEO amount contained in the blend. The average bsfc of
the test fuels obtained were 322.91, 322.81, 325.46,
325.86, 329.76, 333.64, 343.25, 354.21 and 367.17 gr/
kWh for diesel fuel, WEO5, WEO10, WEO15, WEO25,
WEO35, WEO35, WEO50, WEO75 and WEO100 fuels,
respectively. Bsfc is directly affected by the fuel
consumption, power value at corresponding engine
speed and calorific value of the fuel. Since the calorific
value of blend fuels of WEO and diesel fuel is lower than
that of diesel fuel bsfc values of WEO blends were lower
than that of diesel fuels. The exhaust gas temperature
values ever increased with the increase of the engine
speed, for all the test fuels. The lowest exhaust gas
temperature values were obtained for WEO100 fuel. The
highest exhaust gas temperature values were observed
for WEO5, WEO15 and diesel fuels. Exhaust gas
temperature is affected by the combustion temperature,
in-complete and retarded combustion. Lower exhaust
temperature of the engine operation with pure WEO and
WEO blend fuels can be attributed to all the reasons
given above.
Effect on emissions
When the DLF sample is used, the exhaust temperature
is higher than that of the diesel sample, and it increases
with the engine speed. The measured exhaust
temperature varied between 414 and 515°C for the DLF
as compared to 397 and 477°C for diesel indicating
remarkable variation in exhaust temperature. The higher
values in temperatures for the DLF depend on the higher
distillation temperatures, since any fuel distilled at higher
temperature increases combustion temperature when it is
combusted. As a result of the higher combustion
temperature, exhaust gas temperature will increase. High
temperatures in the exhaust are not desirable, for they
cause higher energy transfer from the combustion
chamber to the surrounding. High heat transfer
decreases thermal efficiency of the engine at a finite
value (Arpa et al., 2010a, b). Almost in all speeds of the
engine the WEO100 gave the highest CO emission. At
high speeds of the engine the lowest CO emissions were
obtained from the diesel fuel. All the blend fuels of WEO
and diesel fuel presented very similar CO emissions
except for WEO100, WEO75 and WEO50. However, the
increased engine speed caused to increase air
movements in the engine cylinder which lead to more
homogeneous air-fuel charge and thus resulted in an
improved combustion and consequently lowered CO
emissions. Therefore, when the engine speed increased
CO emissions increased for all test fuels, especially
WEO100 and WEO75 fuels (Cumali and Hüseyin, 2011;
Arpa et al., 2010a, b).
The highest HC emissions were measured for WEO100
and following were WEO75 and WEO50 fuels,
respectively. The lowest HC emissions were observed for
diesel fuel, WEO5, and WEO10 fuels. However, the HC
emissions for WEO25 and WEO35 fuels were quite lower
than that of the WEO100 fuel, and were in acceptable
values. Generally, WEO–diesel blends that contained
high concentrations of WEO lead to a considerably high
amount of HC emissions in the exhaust gasses. The
main reasons, for increased HC and CO emissions for
WEO fuels, are considered to be the poor atomization,
lower cetane number and longer ignition delays. The
higher density, of WEO caused more amounts of fuel to
be injected in mass base, which lead to rich combustion
condition is considered to be the most important reason
of increased HC and CO emissions for WEO and blend
fuels. Besides, the higher final distillation temperature of
WEO might increase HC emissions. All these reasons
which lead to incomplete combustion also lead to
increased HC emission and CO emissions (Cumali and
Hüseyin, 2011; Arpa et al., 2010a, b).
At the lower and medium speeds of the engine diesel
fuel and blends of lower concentration of WEO resulted in
a larger formation of NOx. It can be attributed to the
higher
combustion
temperature
with
improved
combustion. The lowest NOx emissions were obtained for
WEO100 fuel at the lower speeds of engine operation.
However, at the higher speeds of engine operation
WEO100 fuel resulted in higher NOx emissions in
comparison to other test fuels. The reason of this
increase is considered to be the slower combustion of the
WEO100 fuel that results in a larger period of combustion
(Cumali and Hüseyin, 2011; Arpa et al., 2010a, b).
The amounts of SO2 emissions found in the engine
exhaust were almost linear with the WEO amount
contained in the blend and considerably higher than that
of diesel fuel since WEO contains a sulfur amount 4.5
times higher than that of diesel fuel. Therefore, it can be
recommended that the sulfur amount of WEO fuel should
be decreased (Cumali and Hüseyin, 2011; Arpa et al.,
2010a, b).
Results obtained from waste plastic Oil
Effect on performance
From the study of Enweremadu and Rutto (2010);
Mitsuhara et al. (2001); Williams and Williams (1990) and
Mani and Nagarajan (2009b) it can be observed that the
ignition delay of waste plastic oil is considerably longer
than that of diesel. The longer delay period of waste
plastic oil, results in a rise in-cylinder peak pressure. It
Naima and Liazid
may also be seen that the ignition delay is longer by
about 2 to 2.5°CA for waste plastic oil than that of diesel
and the peak pressure increases by 5 bar for waste
plastic oil compared to diesel because of longer ignition
delay.
Mani et al. (2009a), Mani and Nagarajan (2009b), Mani
et al. (2011) found that the cylinder peak pressure for
diesel is 67 bar at rated power and 71 bar in the case of
waste plastic oil. Higher cylinder pressure in the case of
waste plastic oil compared to diesel is due to the
evaporation of waste plastic oil inside the cylinder by
absorbing heat from the combustion chamber. Longer
ignition delay at high load range increases the pressure
of waste plastic oil than that of diesel. In other words, this
period depicts the abnormal combustion or premixed
combustion. However, this is the usual behaviour of highoctane fuel in high compression ratio engines. This can
be controlled by proper selection of compression ratio
(Mani and Nagarajan, 2009b). The authors studied the
variation of cylinder peak pressure with brake power for
waste plastic oil and diesel operation at different. They
noticed that the cylinder peak pressure for the waste
plastic oil is higher than the diesel. The cylinder peak
pressure for diesel increases from 57 bar at no load to 67
bar at rated power and from 54 bar at no load to 71 bar at
rated power in the case of waste plastic oil. In a CI
engine, the peak pressure depends on the combustion
rate in the initial stages, which is influenced by the
amount of fuel taking part in the uncontrolled combustion
phase that is governed by the delay period. It is also
affected by the fuel mixture preparation during the delay
period (Mani et al., 2009).
The maximum heat released in waste plastic oil is high
compared to diesel. It can be noticed that in waste plastic
oil, most of the heat release occurs only during the
premixed combustion. Longer ignition delay results in
higher heat release during the premixed combustion
phase. The heat release rate is higher in the case of
waste plastic oil due to the higher fuel-air ratio. The
higher heat release rate leads to an increase in exhaust
gas temperature (Enweremadu and Rutto, 2010;
Mitsuhara et al., 2001; Mani and Nagarajan, 2009b).
Effect on emissions
Generally, compression ignition engine operates with
lean mixtures and hence the CO emission would be low.
CO emission is toxic and must be controlled (Mani et al.,
2009a; Mani and Nagarajan, 2009b; Mani et al., 2011). It
is an intermediate product in the combustion of a
hydrocarbon fuel, so its emission results from incomplete
combustion. Emission of CO is therefore greatly dependent on the air fuel ratio relative to the stoichiometric
proportions. Rich combustion invariably produces CO,
and emissions increase nearly linearly with the deviation
from the stoichiometry (Murugan et al., 2005). The
41
Concentration of CO emission varies from 14.14 g/kWh
at 25% of rated power to 5.75 g/kWh at rated power for
diesel, whereas it varies from 18.51 g/kWh at 25% of
rated power to 6.19 g/kWh at rated power for waste
plastic oil. The results show that CO emission of waste
plastic oil is higher than diesel. The reason behind
increased CO emission is incomplete combustion due to
reduced in-cylinder temperatures. The drastic increase in
CO emission at higher loads is due to higher fuel
consumption (Mani et al., 2009a; Mani and Nagarajan,
2009b; Mani et al., 2011).
CO2 varies from 1305.97 g/kWh at 25% of rated power
to 789.36 g/kWh at rated power for diesel. It can be
observed that in waste plastic oil it varies from 1163.25
g/kWh at 25% of rated power to 888.715 g/kWh at rated
power. From the results, it is observed that the amount of
CO2 produced while using waste plastic oil is lower than
diesel. This may be due to late burning of fuel leading to
incomplete oxidation of CO (Mani et al., 2009a; Mani and
Nagarajan, 2009b; Mani et al., 2011).
The formation of NOx is highly dependent on in-cylinder
temperature, oxygen concentration and residence time
for the reactions to take place. It can be noticed that the
NOx emission increases in the waste plastic oil operation.
NOx varies from 12.15 g/kWh at 25% of rated power to
7.91 g/kWh at rated power for diesel and from 14.68
g/kWh at 25% of rated power to 8.93 g/kWh at rated
power for waste plastic oil. The reason for the increased
NOx is due to the higher heat release rate and higher
combustion temperature (Mani et al., 2009a; Mani and
Nagarajan, 2009b; Mani et al., 2011).
Unburned hydrocarbon is a useful measure of
combustion inefficiency. Unburned hydrocarbon consists
of fuel that is incompletely burned. The term hydrocarbon
means organic compounds in the gaseous state and solid
hydrocarbons are the particulate matter (Mani et al.,
2009a). At light load, large amounts of excess air and low
exhaust temperature and lean fuel air mixture regions
may survive to escape into the exhaust. Unburned
hydrocarbon varies from 0.431 g/kWh at 25% of rated
power to 0.1389 g/kWh at rated power for diesel. In the
case of waste plastic oil it varies from 0.4393 g/kWh at
25% of rated power to 0.147 g/kWh at rated power. From
the results, it can be noticed that the concentration of the
hydrocarbon of waste plastic oil is marginally higher than
diesel. The reason behind increased unburned
hydrocarbon in waste plastic oil may be due to higher
fumigation rate and non-availability of oxygen relative to
diesel (Mani et al., 2009a; Mani and Nagarajan, 2009b;
Mani et al., 2011).
CONCLUSION
This paper gives a brief review on the conversion process
of the most waste oils available in now days in order to
use them in Diesel Engine. From the results obtained
42
J. Pet. Technol. Altern. Fuels
from various studies we can summarize the following
points:
(i) Results from using waste cooking oil as fuel for diesel
engines showed that the fuel obtained has a higher
viscosity and lower calorific value; this will have a major
bearing on spray formation and initial combustion. The
ignition delay of UCO biodiesel decreases. The peak
pressure of UCO biodiesel and its blends is higher than
that of diesel fuel. WCO showed a higher exhaust gas
temperature compared to diesel fuel. Increased oxygen
content which improves combustion is a reason given for
this. A relatively high disparity of results has been found
regarding the emissions characteristics of used cooking
oil biodiesel and/or its blends. Most of the reports
recorded slight increases in NOx when compared to
diesel at rated load. The reasons most frequently given
include higher oxygen content of biodiesel and its blends
and advanced injection process with biodiesel. CO and
unburned HC emissions were found to significantly
decrease with biodiesel and its blends due to a more
complete combustion caused by higher oxygen content.
(ii) Engine was able to run with 100% waste plastic
oil.Ignition delay was longer by about 2.5°CA in the case
of waste plastic oil compared to diesel. NOx is higher by
about 25% for waste plastic oil operation than that of
diesel operation. CO emission increased by 5% in waste
plastic oil compared to diesel operation.Unburned
hydrocarbon emission is higher by about 15%. Engine
fueled with waste plastic oil exhibits higher thermal
efficiency upto 75% of the rated power.
(iii) Fuel obtained from waste engine oil can be used as
fuel in diesel engines without any problems in terms of
engine performance. The thermal and physical
characteristics of the DLF are close to those values of a
typical diesel sample. Moreover, its distillation
temperature increases gradually, and its behavior is
similar to that of diesel fuels used in engines. When the
DLF was used, it was observed that torque, brake mean
effective pressure and brake thermal efficiency were
higher than those of the diesel sample while the brake
specific fuel consumption was lower.
REFERENCES
Alamu OJ, Akintola TA, Enweremadu CC, Adeleke AE (2008).
Characterization of palm kernel oil biodiesel produced through
NaOH-catalysed transesterification process. Sci. Res. Essays
3(7):308-11.
Al-Ghouti MA, Al-Degs YS, Amer M (2008). Determination of motor
gasoline adulteration using FTIR spectroscopy and multivariate
calibration. Talanta 76:1105e12.
Al-Widyan MI, Tashtoush G, Abu-Qudais M (2002a). Utilization of ethyl
ester of waste vegetable oils as fuel in diesel engines. Fuel Process.
Technol. 76:91-103.
Al-Widyan MI, Al-Shyoukh AO (2002b). Experimental evaluation of the
transesterification of waste palm oil into biodiesel. Bioresour.
Technol. 85:253-256.
Ampaitepin S, Tetsuo T (2010). The waste-to-energy framework for
integrated multi-waste utilization: Waste cooking oil, waste lubricating
oil, and waste plastics. Energy 35:2544-2551.
Arpa O, Recep Y, Zeki A (2010a). Experimental investigation of the
effects of diesel-like fuel obtained from waste lubrication oil on engine
performance and exhaust emission. Fuel Process. Technol. 91:12411249.
Arpa O, Yumrutas R, Alma MH (2010b). Effects of turpentine and
gasoline-like fuel obtained from waste lubrication oil on engine
performance and exhaust emission. Energy 35:3603-3613.
Bhaskar T, Uddin MA, Muto A (2004). Recycling of waste lubricant oil
into chemical feedstock or fuel oil over supported iron oxide catalysts.
Fuel 83:9e13.
Canakci M, Van-Gerpen J (2001). Biodiesel production from fats and
oils with high free fatty acids. Trans ASAE. 44(6):1429-1436.
Cumali I, Hüseyin A (2011). Fuel production from waste vehicle
tires by catalytic pyrolysis and its application in adiesel engine. Fuel
Process. Technol. 92:1129-1135.
Demirbas A, Demirbas I (2007). Importance of rural bioenergy for
developing countries. Energy Convers. Manag. 48:2386-2398.
Dorado MP, Ballesteros E, Arnal JM, Gomez J, Lopez-Gimenez FJ
(2003). Testing waste olive oil methyl ester as a fuel in a diesel
engine. Energy Fuels 17:1560-1565.
Dorado MP, Ballesteros E, Mittelbach M, Lopez FJ (2004). Kinetic
parameters affecting the alkali-catalyzed transesterification process
of used olive oil. Energy Fuels 18:1457-1462.
Dunn RO, Shockley MW, Bagby MO (1996). Improving the lowtemperature properties of alternative diesel fuels: Vegetable-oil
derived methyl esters. J. Am. Oil Chem. Soc. 73(12):1719-1728.
Enweremadu CC, Rutto HL (2010). Combustion, emission and engine
performance characteristics of used cooking oil biodiesel-A review.
Renew. Sustain. Energy Rev. 14:2863-2873.
Enweremadu CC, Mbarawa MM (2009). Technical aspects of biodiesel
production and analysis from used cooking oil: A review. Renew.
Sustain. Energy Rev. 13:2205-2224.
Etinkaya CM, Ulusoy Y, Tekin Y, Karaosmanog˘lu F (2005). Engine and
winter road test performances of used cooking oil originated
biodiesel. Energy Convers. Manag. 46:1279-1291.
Fuentes MJ, Font R, Gómez-Rico MF, Martín-Gullón I (2007). Pyrolysis
and combustion of waste lubricant oil from diesel cars:
Decomposition and pollutants. J. Anal. AppL. Pyrol. 79:215-226.
Gonzalez-Gomez ME, Howard-Hildige R, Leahy JJ, O’Reilly T, Supple
B, Malone M (2000). Emission and performance characteristics of a
2L Toyota diesel van operating on esterified waste cooking and
mineral diesel fuel. Environ. Monitor Assess. 65:13-20.
Guang-Hua Z, Jun-Feng Z, Okuwaki A (2007). Prospect and current
status of recycling waste plastics and technology for converting them
into oil in China. Resourc.Conserv. Recy. 50:231-239.
Hai VP, Nishida O, Fujita H, Harano W, Toyoshima N, Iteya M (2001).
Reduction of NOx and PM from diesel engines by WPD emulsified
fuel, SAE Technical Paper -01-0152.
Jerzy W (2002). Engine fuel derived from waste plastics by thermal
treatment. Fuel. 81:473-481.
Karthikeyan R, Mahalakshmi NV (2007a). Performance and emission
characteristics of a turpentineediesel dual fuel engine. Energy
32(7):1202-1209.
Karthikeyan R, Mahalakshmi NV (2007b). Performance and emission
characteristics of turpentineediesel dual fuel engine and knock
suppression using water diluents. Int. J. Energy Res. 31:960-974.
Koç M, Sekmen Y, Topgul T, Yucesu HS (2009). The effect of
ethanoleunleaded gasoline blends on engine performance and
exhaust emissions in a sparkignition engine. Renew. Energy
34:2101-2106.
Kulkarni MG, Dalai AK (2006). Waste cooking oil – an economical
source for biodiesel: A review. Ind. Eng. Chem. Res. 45:2901-2913.
Lapuerta M, Armas O, Ballesteros R (2002). Diesel particulate
emissions from biofuels derived from Spanish vegetable oils. SAE
Paper No. -01-1657.
Li XX, Shi YF, Yu HR (2002). Preparation of fuel oil from plastic waste
by catalytic cracking. Environ. Protect Chem. Ind. 22(2):90-94.
Liu GZ, Chen ET (2001). Catalytic cracking of scrap plastics into
gasoline and diesel oil by a pilot experiment unit. Environ. Sci.
Technol. 98(6):9-10.
Mani M, Subash C, Nagarajan G (2009a). Performance, emission and
Naima and Liazid
combustion characteristics of a DI diesel engine using waste plastic
oil. Appl. Therm. Eng. 29:2738-2744.
Mani M, Nagarajan G (2009b). Influence of injection timing on
performance, emission and combustion characteristics of a DI diesel
engine running on waste plastic oil. Energy 34:1617-1623.
Mani M, Nagarajan G, Sampath S (2011). Characterisation and effect of
using waste plastic oil and diesel fuel blends in compression ignition
engine. Energy 36:212-219.
Mitsuhara Y, Soloiu VA, Nakaishi Y (2001). Application of new fuel
produced from waste plastics and heavy oil to diesel engine.
Transact. Jpn. Soc. Mech. Eng. 67:2618-2624.
Mittelbach M, Gangl S (2001). Long storage stability of biodiesel made
from rapeseed and used frying oil. J. Am. Oil Chem. Soc. 78:573577.
Murugan S, Ramaswamy MC, Nagarajan G (2005). Tyre pyrolysis oil as
an alternate fuel for diesel engines, SAE Paper -01-2190.
Nerin C, Domeno C, Moliner R, Lazaro MJ, Suelves I, Valderrama J
(2000). Behavior of different industrial waste oils in a pyrolysis
process: metals distribution and valuable products. J. Anal. Appl.
Pyrol. 55:171-183.
Rao GLN, Sampath S, Rajagopal K (2008). Experimental studies on the
combustion and emission characteristics of a diesel engine fuelled
with used cooking oil methyl ester and its diesel blends. Int. J. Appl.
Sci. Eng. Technol. pp. 64-70.
Schumacher LG, Borgelt SC, Hires WG, Fosseen D, Goetz W (1994).
Fueling diesel engines with blends of methyl ester soybean oil and
diesel
fuel.
Available
from:
www.missouri.edu/_pavt0689/ASAED94.htm.
Sebastian V, Thomas W (2009). Hydrogen-fueled internal combustion
engines. Progress Energy Combust. Sci. 35:490-527.
Sinha S, Agarwal AK (2005). Combustion characteristics of rice bran oil
derived biodiesel in a transportation diesel engine. SAE Paper No.
01-1730.
43
Soloiu A, Yoshihara Y, Hiraoka M, Nishiwaki K, Mitsuhara Y, Nakanishi
Y (2000). The investigation of a new diesel produced from waste
plastics. ISME.
Ulusoy Y, Tekin Y (2004). The engine tests of biodiesel from used frying
oil. Energy Source 26:927-932.
Usta N, Öztürk Ö, Can ES, Conkur S, Nas AH (2005). Combustion of
biodiesel fuel produced from hazelnut soapstock/waste sunflower oil
mixture in a diesel engine. Energy Convers. Manag. 46:741-755.
Williams PT, Williams EA (1990). Interaction of plastics in mixed plastics
pyrolysis. J. Energy Fuels. 13:188-196.
Wang L, Luo GH, Li Q (2003). Progress of waste plastics pyrolysis.
Chem. Ind. Eng. Progr. 22(2):130-134.
Xiangmei
M,
Guanyi
C, Yonghong
W
(2008).
Biodiesel
production from waste cooking oil via alkali catalyst and its engine
test. Fuel Process. Technol. 89(9):851-857.
Yumrutas¸R, Alma MH, Özcan H, Kaska Ö (2008). Investigation of
purified sulfate turpentine on engine performance and exhaust
emissions. Fuel 87:252-259.
Zafer U, Mevlüt SK (2008). The effect of biodiesel fuel obtained from
waste frying oil on direct injection diesel engine performance and
exhaust emissions. Renew. Energy 33:1936-1941.