Предложенна конструкци центробежной мельницы в отличие от мельницы, описанной в авт. св. № 70859, дает возможность получить вентил ционный эффект, преп тствующий проникновению пыли из рабочего пространства мельницы в помещение под ротором, за счет наличи зазора между неподвижным кожухом и ротором и наклонно расположенными част ми стенок ротора и кожуха.The proposed construction of a centrifugal mill as opposed to the mill described in ed. St. No. 70859, makes it possible to obtain a ventilation effect that prevents the penetration of dust from the working space of the mill into the room under the rotor, due to the presence of a gap between the fixed casing and the rotor and obliquely arranged parts of the rotor and casing walls.
Центробежна мельница (см. чертеж) состоит из чаши / с кольцом 2. Вал мельницы 3 имеет приводной шкив 4 и подшинники качени , смонтированные в стакане, установленном в плите 5. На плите расположен цилиндрический корпус 6, внутри которого укреплено неподвижное кольцо 2. Корпус снабжен крыщкой и патрубками 7, 8, 9, 10 и //. Патрубок 8 может устанавливатьс по высоте с помощью подъемного устройства 12. Процесс работы мельницы происходит следующим образом .The centrifugal mill (see drawing) consists of a bowl / ring 2. The shaft of the mill 3 has a drive pulley 4 and rolling pads mounted in a glass mounted in plate 5. On the plate there is a cylindrical body 6 inside which a fixed ring 2 is fixed. equipped with a lid and nozzles 7, 8, 9, 10 and //. The pipe 8 can be installed in height with the help of a lifting device 12. The operation of the mill is as follows.
Материал загружаетс питателем через патрубок 10, падает в чаlijy и образует внутри нее слой, удерживаемый в чаше кольцом 13. Следующие порции материала не удерживаютс кольцо.м и выбрасываютс из чаши центробежной силой на неподвижное кольцо 2, где образуетс слой материала, защищающий цилиндрическую часть корпуса. После этого выброшенный из чащи материал вновь падает в чащу и вновь выбрасываетс из нее и т. д. Таким образом, происходит непрерывна циркул ци материала между вращающейс чашей и неподвижным корпусом .The material is loaded by the feeder through pipe 10, falls into the cup and forms inside it a layer held in the bowl by ring 13. The following portions of material do not hold the ring. They are thrown out of the bowl by centrifugal force on the fixed ring 2, where a layer of material is formed that protects the cylindrical part of the body . After that, the material thrown out of the thicket again falls into the thicket and is again thrown out of it, and so on. Thus, a continuous circulation of the material occurs between the rotating cup and the stationary body.
Размол продукта происходит вследствие того, что част1щы матери; ла , выбрасываемые из чащи со значительной скоростью, удар ютс с больщой силой о внутреннюю поверхность корпуса и защитный слой материала на неподвижном кольце и, растира сь друг о друга, постепенно разбиваютс .Grinding of the product is due to the fact that parts of the mother; La, thrown out of the thicket with considerable speed, hit with great force against the inner surface of the body and the protective layer of material on the fixed ring and, rubbing against each other, gradually break.
Воздух, вл ющийс транспортным средством дл размолоты.х частиц материала, поступает во внутреннюю часть корпуса двум пут ми: через патрубок 9-только в необходи.мом количестве и через кольцевую .между кольцом 13 чаши и неподвижным кольцом 2.The air, which is a vehicle for grinding material particles, enters the interior of the housing in two ways: through pipe 9 - only in the required quantity and through the ring between ring 13 of the bowl and the stationary ring 2.
Особенностью конструкции мельницы вл етс форд1а внешней поверхности чаши с уклоном кнаружи, вследствие чего эта поверхностьThe design feature of the mill is the ford1a of the outer surface of the bowl with a slope outwards, as a result of which this surface