с кулачками, а концы пружин вход т в кольцевой паз 18 корпуса обоймы. Пазы 20 в |Кулачках имеют пр молинейное основание , что допускает изгиб пружины внутрь паза. Срезной винт 22 фиксирует обойму относительно головки 5 в положении, когда конусна часть головки находитс над кулачками. Срезной винт 23 фиксирует на стволе 4 опорное кольцо 9.with cams, and the ends of the springs fit into the annular groove 18 of the casing body. The grooves 20 in the cams have a straight base, which allows the spring to be bent into the groove. The shear screw 22 secures the sleeve relative to the head 5 in a position where the tapered portion of the head is above the cams. The shear screw 23 fixes a support ring 9 on the barrel 4.
При спуске пакера в скважину и достижении Им установочной муфты 1, опорнре кольцо 9 садитс на опорньш выступ Пи тогда при нагружении пакера весом насосно-жомпрессорных труб до расчетного значени срезаютс винты 23, ствол 4 продвигаетс несколько вниз, а вес труб через головку 5, винты 22, обойму 7 передаетс на уплотнитель 8, наход щийс в это врем внутри устаиовочной муфты между выступом 11 и выточкой 12 и начинает деф )0рмироватьс .When the packer is lowered into the well and The installation sleeve 1 is reached, the support ring 9 sits on the supporting protrusion Pi then, when the packer is loaded with the weight of the pump and compressor pipes, the screws 23 are cut to the calculated value, the trunk 4 moves down slightly, and the pipes weight through the head 5 screws 22, the sleeve 7 is transferred to the seal 8, which at this time is inside the installation sleeve between the protrusion 11 and the recess 12, and begins to deflate.
При дальнейшем нагружении пакера весом насосно-компрессорных труб и продолжающейс деформацией уплотнител срезаютс винты 22, после чего ствол 4 с головкой 5 продвигаетс вниз, а обойма с кулачками, опирающа с на уплотнитель, остаетс на месте. Головка своей конической частью переводит кулачки 19 в раздвинутое положение, а нижним торцом 24 упираетс на внутренний торец корпуса 14 обоймы, передава вес труб через корпус обоймы уплотнителю 8 и полностью пакеру скважину. Раздвинутые кулачки 19 вход т при этом в выточку :12 муфты /, а их пружины 21 в результате изгиба приход т в упругое состо ние. В этом положении осуществл етс эксплуатаци .Upon further loading of the packer with the weight of the tubing and the continued deformation of the seal, screws 22 are cut off, after which the barrel 4 with the head 5 moves downward and the cage with the cams resting on the seal is left in place. The head with its tapered part transfers the cams 19 to the extended position, and with the lower end 24 rests on the inner end of the casing 14, transferring the weight of the pipes through the casing to the seal 8 and the well to the packer. In this case, the extended cams 19 enter the recess: 12 clutches /, and their springs 21 become elastic in the result of bending. In this position, operation is carried out.
При превышении давлени снизу нагрузки на пакер кулачки 19 фасками 25 When the pressure is exceeded from the bottom load on the packer, the cams 19 by chamfers 25
упираютс в фаску 13 на верхней стороне выточки 12 установочной муфты.abutted against the bevel 13 on the upper side of the recess 12 of the mounting sleeve.
Подъем пакера из скважины осуществл етс простым подъемом труб, при этом движетс вверх стол с головкой, когда поднима сь, освобождает в обойме пространство , в которое под действием пружин 21 возвращаютс в утопленное положение кулачки 19, после чего они не преп тствуют подъему пакера. Торец 26 головки 5 подхватывает за внутренний бурт втулки 15 обойму 7 и поднимает ее над уплотнением , освобожда его от нагрузки. Затем муфта 10 подхватывает опорное кольцо 9, которое, двига сь вверх срывает уплотнитель 8.The packer is lifted out of the well by simply lifting the pipes, while the table with the head moves upwards, when raised, clears a space into which the cams 19 return to the recessed position under the action of springs 21, after which they do not prevent the packer from lifting. The end face 26 of the head 5 picks up the sleeve 7 by the inner collar of the sleeve 15 and raises it over the seal, releasing it from the load. Then the coupling 10 picks up the support ring 9, which, moving upwards, tears off the seal 8.