рационного усилител (ОУ) 2 с источниками питани 3 и 4, МОП-транзисторов обратной св зи 5-1-5-й, коммутирующих МОП-транзисторов 6-1-б-п и 7-1-7-п, образцовых резисторов 8-1-8-п, переменных резисторов 9-1-9-п и общего дл всех разр дов посто нного резистора 10.radio amplifier (op-amp) 2 with power sources 3 and 4, feedback MOSFETs 5-1-5th, switching MOSFETS 6-1-bp and 7-1-7-p, exemplary resistors 8 -1-8-p, variable resistors 9-1-9-n, and common to all bits of the constant resistor 10.
Устройство работает следующим образом . Допустим, что управл ющий импульс с блока управлени поступает на затворы МОП-транзисторов второго разр да магазина . В этом случае открываютс МОПтранзисторы 6-2, 7-2, 5-2, цепь отрицательной обратной св зи, образованна транзисторами 7-2, 5-2, замыкаетс . Напр жение с выхода операционного усилител 2 через делитель, состо щий из резисторов 9-2 и 10 и переходного сопротивлени открытого транзистора 6-2, подаетс на пр мой вход операционного усилител 2. С помощью переменного резистора 9-2 осуществл етс регулировка коэффициента делени делител и, тем самым, эффективного сопротивлени между контактами ключа - общей точкой источников питани усилител и точкой соединени стоков транзисторов 7-2, 5-2. Измен эффективное сопротивление ключа, можно устранить технологический разброс образцового резистора 8-1. Работа других разр дов магазина происходит аналогично . Использование одной активной ключевой схемы дл коммутации л образцовых резисторов позволило дл регулируемьтх делителей использовать один общий резистор 10. При применении в качестве резистора 10 термосопротивлени удаетс в значительной мере скомпенсировать термозависимость образцовых резисторов 8-1-8-п.The device works as follows. Suppose that the control pulse from the control unit is supplied to the gates of the second-order MOS transistors of the store. In this case, MOPtransistors 6-2, 7-2, 5-2 open, the negative feedback circuit formed by transistors 7-2, 5-2 is closed. The voltage from the output of the operational amplifier 2 through a divider consisting of resistors 9-2 and 10 and the contact resistance of the open transistor 6-2 is fed to the direct input of the operational amplifier 2. Using a variable resistor 9-2, the division factor of the divider is adjusted. and, thereby, the effective resistance between the key contacts — the common point of the power supply sources of the amplifier and the connection point of the drain of the transistors 7-2, 5-2. By changing the effective resistance of the key, you can eliminate the technological variation of the reference resistor 8-1. The work of the other bits of the store is similar. The use of one active key circuit for switching standard resistors made it possible to use one common resistor 10 for controllable dividers. When using thermal resistance as the resistor 10, it is possible to substantially compensate the thermal dependence of the model resistors 8-1-8-p.