SU66176A1 - Adaptation to a condenser for automatic cotton sampling - Google Patents

Description

CAPACITOR ACCESSORIES FOR AUTOMATIC COTTON SAMPLING

For October 4, 1940, in the People's Commissariat of Textiles No. 37153 (319993) Published on April 30, 1946

With a breakdown of the shredded tool, an automatic sampling of the clapper is made from the condensate screen drum during the repair period, corresponding to a half of the press section, for another device connected to the pressure cylinder 5) and the speed of the cylinder and the driver will start. (nor, corresponding to the half-full of the second puppy.

Distinctive feature

The adaptation is that for transferring a portion of the cotton from the drum of the drum to the sample boxes, a part along the length of the removable roller of the co-condenser, the pulses are disconnected periodically from the entire roll and rotated (after turning off) in the direction of the swelling.

Hai drawing fi1g. 1 shows the overall cxeMfy of the arrangement, in FIG. 2 is an exemplary embodiment of the resetting roller of the condenser c, being disconnected for a 1, 1, non-revrosive part, and FIG. 3 - hydraulic communication circuit with wInd luS

with g kd | ravl; "e10ki1M cylinder press.

In the drawing, a U-condenser drum, a 2-detachable paddle roller, a 5 compacting roller, a 4-elevator with drawers (nori) on an endless chain, the upper sprocket of which is leading, 5-hooks for samples, 6-hooks, by which chains are hinged on the hinges, 7 is inclined sloping planes, 8 is a protective shield with a rubber flexible strip, which allows the slam to hit the sprocket and guide the sample into the box, 9 is a block that sits on the axis of the ejector roller, transmitting the rotation cross-over cable mb UO, loosely se He has a blade roller 2 on the axis, an I-cam clutch with two fingers, entering the butt of the reversing end of the roller. By means of these fingers, there is psgotny contact between the coupling - the slider P and the reversing roller, 12-pin with cams, creasing on the shaft of the removable (strip) roller, 13 - reversing

roller end, 14 - clutch lever. 15 - spring-lever, providing a permanent connection of the reversal on the end of the steel N 0 TH: frequent removable roller, 16-cylinder hydrom-Akhanichsky mbhai (izmma sampler automatic machine. In the cylinder along the pipe enters the liquid through the key box, box koto.rs1y K la: pan otre: rumble "po.Vang on pressure, approximately 100 atm, 17 - cylinder plunger, 18-dog, 19-spring to reverse the stroke of the plunger. 20 - yoke carrying from the tank, 21 - gear wheel, С1 is freely seated on the shaft 25 of the upper sprocket of the elevator, 22 is the storage wheel connected to the shaft of the 25 zvedeochkm, 23-з hooked rake., fastened on the plunger, 24 - ball.np) a dog sitting on a snoring dog, 26 - a garbage disposal panel, 27 - a fiber ramp, samples, a 28-lid box, 29 - an emphasis.

Before launching into; the nipodooTiscaler; reversible part of the removable roller is engaged with the rest; part of the roller and helps him to dump the canvas of chlolka on the tray.

When (Approximately a bale is tamped in the Press section, i.e. when the pressure of the IB cylinder of the press is three and the pressure of the previous bale reaches 100 atm, the intermediate intermediate valve box will raise the clan pressure. the wheel 23 rails 23 will start to go up and down and, therefore, through the dog 24 and the ratchet 22, with which the elevator will go, lowering the drawer from position A to position 6. At the same time, the K | and for the boxer slap 5. When the boxer will occupy the floor The middle between A and B, the dog 18 will begin to press the end of the lever 14 and turn off the muff; that //, put it into engagement with the block 10. At this moment the reversible part of the removable roller

It will double with speed (rotate in the opposite direction, dropping the fiber into the shch1k. After a few seconds, the dog 18 will jump off the end of the lever 14 and the spring, 15 will again transfer the coupling 11 into the connection with the cam washer / 2, as shown in fig. 2 The rotation of the reverse end of the vagus will become normal and the selection of the hfob will stop.; Then the plunger / 7 will reach the upper position; NII will stop, as a result of which the nori with boxes will stop.

After pressing in the bale, when the pressure in the cylinder drops “like 100 atm; m, the spring 19 will lower the plunger down. The rake 23 is spinning the wheel 21, will not rotate the snore. The dog 18 lovernets “and its hinge in the collar 20 and slip through the end of the starter 14, is set to its original position. When the next bale begins to be pressed and is compressed with a pressure of up to 100 atm1, the cycle of operation of the machine nai-gpet will be repeated.

The next, filled with probing crates, dropping into position B and touching the slope 7, uncoupled and slid down onto the slope, engaged in the coloration of G.

In order to trash through the bottom, the condenser grids would not fall into the withdrawn products: a wave, under the drum, an inclined iron flap 26 would be installed, the waste, trash to the dust under the condenser.

Envisions and appeals

Claims (2)

1. An adaptation to a condenser for automatic sampling of cotton, characterized in that for gears 1 and 2 of the hlock, the length along the length of the removable roller 2 of the condenser is disconnected periodically from the entire roller and rotating in the reverse direction when sampling. 2. When adjusting according to claim 1, use of an elevator equipped with working buckets 5. 3 : i g / / No. 66176 - 4 FIG. 2