Ловильнын инструмент 4 состоит из конического корпуса 15 с плаш«а-ми 16.Lovilnyn tool 4 consists of a conical body 15 with a flat “a-mi 16.
В нижней части корпуса 1 раз.мещвн дополнительный узел захвата, содержащий плашки 17, перемещающиес ло коничбокой pacTDHiKe, вы1ПОЛ|Нен1НОЙ а внутренней поверхности корпуса /. Плащжа /7 фижси-рует прихваченный инструмент 18 в корпусе / при опускании ствола 5, а упоры 19 предотвр ащают перемещение ствола 5 вверх при входе ловильного инструмента в полость прихваченного инструмента 18.In the lower part of the body, 1 additional displacement grip assembly containing the dies 17, moving with a tapered pacTDHiKe, 1POL | HEN1 and the inner surface of the housing / is located 1 time. Cloak / 7 fiksi-ruet stuck tool 18 in the housing / when lowering the barrel 5, and the stops 19 prevent the barrel 5 from moving upwards when the fishing tool enters the cavity of the stuck tool 18.
Предлагаемое устройство опускаетс в сйважину на насосно-ком реосорлых трубах 13. Конический корпус 15 вводитс в ннструМент /5, 1при этом плашки 16, (Перемеща сь по наклонным плоскост м корпуса 15, перемещаютс Вверх. В трубы 13 прокачиваетс ж идкость, втулка 14 перемещаетс ;вверх, раздвига и прижима корь 3 к стенкам эксплуатационной колоыны 20 или скважины. После этого произ1водитс частична разгрузка подъемных труб 13. Одвавременно с этим упоры 19 раздвигаютс , и ствол 5 под давлением промывочной жидкости, поступающей в камеры 11, поднимаетс вверх, увлека ловиль ый инструмент 4 с прихваченным инструментом 18. При этом общее усилие, развиваемое гидроусилителем 2, складываетс из усилий, создаваемых в камерах 1Q. Зна площадь сечени ствола 5 и количество секций , по давлению определ етс развиваемое гидроусилителем 2 подъеммое усилие.The proposed device is lowered into the well on pumping-and-rotary pipes 13. The conical body 15 is inserted into the tool / 5, 1 with this die 16, (Moving along the inclined planes of the body 15, moves up. The liquid 13 is pumped through the fluid, the sleeve 14 moves ; up, pushing and pressing the bark 3 to the walls of the production pipe 20 or well. After this, the lifting pipes 13 are partially unloaded. At the same time, the stops 19 move apart and the barrel 5 rises under pressure from the flushing fluid entering the chambers 11 upwards, entraining catch the first tool 4 with the stuck tool 18. The total force exerted by the booster 2, folded from the forces generated in 1Q chambers. By knowing the area of the trunk section 5, and the number of sections determined by the pressure developed by the hydraulic booster 2 podemmoe force.
Окончание каждого цикла подъема прихваченного инструмента определ ют по паде«ию давлени в подъвм1ных трубах 13, так как кольцева проточка 6 ствола 5 при прохождении через канал в днище нижней секции гидроусилител 2 (см. фиг. 2), сообщает полость труб 13 с затрубньш пространством. После этого ствол 5 под собственным весом опускаетс вниз, а П1ри гва чен1ный инструмент 18 удержи1ваетс за наружную поверхность плашками 17. Прн повторной подаче жидкости в полость труб 13 ствол 5 вновь перемещает прихваченный инструмент 18 вверх, при этом плащки /7 беопреп тственно пропускают И Н|Струмбнт 18 внутрь корпуса / (см. фиг. 3).The end of each cycle of lifting the stuck tool is determined by the pressure drop in the lift pipe 13, since the annular groove 6 of the barrel 5 when passing through the channel in the bottom of the lower section of the hydraulic booster 2 (see Fig. 2), informs the cavity of the pipe 13 with annular space . After this, the barrel 5 under its own weight goes down, and once the tool 18 is held on the outer surface with the dies 17. When the fluid is re-supplied into the cavity of the pipes 13, the barrel 5 again moves the stuck tool 18 up, while the cloaks / 7 are passed through and N Strumbnt 18 inside the case / (see Fig. 3).
После оовобон дени прихваченного инструмента 18 давление в трубах 13 сбрасываетс и плащки кор 3 занимают исходное положение, не преп тству подъему труб 13 с инструментом /5 наземным оборудованием.After the tool 18 is stuck in the air, the pressure in the pipes 13 is released and the cloaks of the core 3 are in their original position, without obstructing the lifting of the pipes 13 with the tool / 5 by ground equipment.
Применение описанного устройства позвол ет перемещать прих1ваченный инструмент на значительную высоту с фиксацией момента окончани каждого цикла подъема и тем самым повысить эффективность работ по оовобождению и подъему прихваченного инструмента .The use of the described device allows the tool to be moved to a considerable height while fixing the moment of the end of each lifting cycle and thereby increasing the efficiency of work on the lifting and lifting of the stuck tool.