(54) УСТРОЙСТВО ДЛЯ КОНТРОЛЯ РАБОЧИХ ХОДОВ ПРЕССА(54) DEVICE FOR THE CONTROL OF WORK POSITIONS OF THE PRESS
При выполнении рабочей операции при исправном оборудовании в результате обработки низкочастотной огибающей фазного тока в преобразователе 1, формирователе 2, на входах пересчетного блока 3 и селектора 6 по вл етс импульсный код, соответствуюидий каждому элементу рабочего цикла. При этом на выходе пересчетного блока 3 по вл етс сигнал о совершении рабочего цикла, поступающий на вход элемента запрета 4, на запрещающий вход которого поступает сигнал с основного выхода 9 селектора 6. Одновременно счетчик .10 фиксирует факт изготовлени детали. В конце цикла задатчик 11 сбросит пересчетный блок. При выполнении рабочей операции .и неисправном оборудовании возможны два случа : неисправность про вл етс уже, при включении муфты и разгоне маховых масс; неисправность про вл етс после разгона маховых масс, т., е. при выполнении рабочей операции.When a working operation is performed with good equipment, as a result of processing the low-frequency envelope of the phase current in converter 1, driver 2, the impulse code appears at the inputs of converter block 3 and selector 6, corresponding to an element of each work cycle element. In this case, the output of the scaling unit 3 shows a signal about the performance of a working cycle, which enters the input of the prohibition element 4, to the prohibitory input of which a signal is received from the main output 9 of the selector 6. At the same time, the counter. At the end of the cycle, the setting device 11 will reset the scaling unit. When performing a working operation and faulty equipment, two cases are possible: a malfunction is already manifested when the clutch is turned on and acceleration of the flywheel masses; a malfunction occurs after acceleration of the flywheel masses, i.e., when performing a working operation.
В первом случае сигналы не по в тс ни на основном 9, ни на дополнительном 7 выходах селектора 6 кодированной серии, а индикатор 5 неисправности выдаст сигнал об отказе оборудовани . Во втором случае сигнал по витс на дополнительном выходе 7 селектора 6, а индикатор. 8 холостого хода выдаст сигнал о регистрации только холостого хода. Аналогично второму случаю осуществл етс работа устройства при выполнении холостого хода.In the first case, the signals are not similar to either the main 9 or the additional 7 outputs of the coded series selector 6, and the malfunction indicator 5 will give a signal that the equipment has failed. In the second case, the signal is turned on at the additional output 7 of the selector 6, and the indicator. 8 idle will give a signal to register only idle. Similarly to the second case, the device operates while idle is running.
Предлагаемое устройство позвол ет повысить точность контрол прессового оборудовани , а также обеспечить автоматическое дифференцирование причин отказа устройства. Последнее обеспечиваетс при помощи индикатора холостого хода, позвол ющего вы вить, в какой области временной диаграммы лежит неисправность .The proposed device allows to increase the accuracy of control of the pressing equipment, as well as to provide automatic differentiation of the causes of failure of the device. The latter is provided by means of an idling indicator, which allows finding out in which area of the timing diagram the fault lies.