Claims (2)
поперечное сечение распылитель го патрубка с насадкой. Предлагаемое устройство состоит из воздуховода 1, подвод щего сжатый воздух, .патрубка 2 с регулируе мым дросселем 3, бункера 4, подвод щего трубопровода 5, отвод щей труб ки б, регулировочного винта 7, пылезаправочного отверсти с пробкой 8, распылительно патрубка 9с игольной насадкой 10 и раструба 11. Работает устройство следующим образом. Вункер 4 через пылезаправочное отверстие засыпают порошком и закрьшают пробку 8. Сжатый воздух через воздуховод 1 поступает в патрубок 2, а через регулируемый откры тый дроссель 3 - в распылительный патрубок 9, проходит вдоль игольной насадки 10 по капилл рам и через раструб 11 внходит наружу. При пережимании сечени патрубка 2 регулируемым дросселем 3 часть сжатого газа идет в подвод щий трубопровод 5 и далее в нижнюю част бункера 4. Пылегазова смесь из бункера 4 подаетс в патрубок 2 по отвод щей трубке 6. В распылительно патрубке 9 аэрозоль проходит с пот ком сжатого газа через игольную насадку 10 и дезагрегированный выходит из раструба 11. Аэрозоль проходит с большой скоростью в промежутках между иголками и за счет значительного градиента скоростей газового потока на стенке капилл ра и в середине свободного промежутка происходит разрушение пылевых агрегатов. Измен диаметр игл в насадке 10 можно приспособить устройство дл распылени материалов. разной диспе ности. .(Саналы между иглами имеют малое поперечное сечение, поэтому несмотр на высокую скорость газа на выходе из насадки 10 скоро устанавливаетс ламинарный режим течени пылегазовой смеси и аэрозоль ока зываетс равномерно распределенн м по всему сечению раструба 11. Это необходимо в случае применени устройства дл тарировки пылегазоэых приборов. Ввиду того, что контакт аэрозольных частиц с игольной насадкой 10 кратковременный, электрическа зар дка частиц в устройстве значительно уменьшаетс . Преимуществом распылител вл етс простота изготовлени , обеспечение ламинарного режима течени пылегазового потока, выравнивание пылевой концентрации после раструба, а также уменьшение электростатического зар да на частицах пыли. Формула изобретени Распылитель пороншовых материалов, содержащий соединенный с бункером дл порошка распылительный патрубок и систему пневмоподачи порошка, о тличающийс тем, что, с целью улучшени распылени аэрозол и выравнивани пол скоростей пылегазового потока после распылител , распылительный патрубок снабжен насадкой из плотно уложенных по всему его сечению цилиндрических игл, обращенных остри ми к входному отверстию патрубка. Источники информации, прин хые во внимание при экспертизе: 1.Авторское свидетельство СССР 185493, ;;л, В 22 Р 1/00, 1965. cross section of a spray nozzle with a nozzle. The proposed device consists of an air duct 1, supplying compressed air, a pipe 2 with an adjustable choke 3, a bunker 4, a supply pipe 5, a discharge pipe b, an adjusting screw 7, a filling hole with a stopper 8, a spray nozzle 9 with a needle nozzle 10 and the socket 11. The device operates as follows. The hopper 4 is poured into the powder through the dusting hole and closes the plug 8. Compressed air enters the nozzle 2 through the air duct 1, and through the adjustable open throttle 3 into the spray nozzle 9, passes along the capillaries and through the nozzle 11 goes out. When clamping the cross section of the pipe 2 with an adjustable choke 3, a part of the compressed gas goes to the supply pipe 5 and further to the lower part of the bunker 4. The dust and gas mixture from the hopper 4 is fed to the pipe 2 through the discharge pipe 6. In the spray pipe 9 the aerosol passes with compressed air gas through the needle nozzle 10 and disaggregated out of the socket 11. The aerosol passes at high speed in the intervals between the needles and due to a significant gradient of gas flow velocities on the capillary wall and in the middle of the free gap Diet destruction of dust aggregates. By changing the diameter of the needles in the nozzle 10, a device for spraying materials can be adapted. different range. (The sleeves between the needles have a small cross section, therefore, despite the high gas velocity at the exit of the nozzle 10, the laminar flow regime of the dust-gas mixture is quickly established and the aerosol is evenly distributed throughout the cross section of the socket 11. This is necessary if the device is used for calibrating dust and gases Because the contact of the aerosol particles with the needle nozzle 10 is brief, the electrical charge of the particles in the device is significantly reduced. The advantage of the sprayer is the simplicity manufacturing, ensuring the laminar flow of the dust-gas flow, leveling the dust concentration after the socket, and reducing the electrostatic charge on the dust particles Formula of the sprayer containing the spray nozzle connected to the powder hopper and powder pneumatic supply system, in order to improve aerosol spraying and leveling the velocity of the dust and gas flow after the sprayer, the spray nozzle is equipped with a nozzle from cylindrical needles across its cross section, which are pointed at the inlet of the nozzle. Sources of information taken into account in the examination: 1. Author's certificate of the USSR 185493, ;; l, H 22 P 1/00, 1965.
2. Авторское свидетельство СССР О 245730, кл. В 01 J 17/24, 1967.2. USSR author's certificate O 245730, cl. B 01 J 17/24, 1967.