(54) АКУСТООПТИЧЕСКИЙ СПЕКТРОАНАЛИЗАТОР(54) ACOUSTIC TECTRIC ANALYZER
хождение лучей пулевого пор дка через стекл нпую пластину.walking bullet rays through a glass plate.
Анализируемый сигнал подаетс па вход ультразвукового модул тора 5 и одповременно запускает генератор ЛЧМ сигнала 6 и ипдикаторное устройство 13. Геператор 6 формирует сптиал с линейной частотной модул цией длительностью, большей вре-мепи задержки модул тора 4. При «заполнении анертуры модул тора 4 управл ющим ЛЧМ си1-иало-м па выходе линзы формируютс дифракционные пор дки. По мере дальпейшего про.хожденн спгнала через модул тор 4 происходит перемеидение первых пор дков дифракции в направлении, пернепдикул риом оптической оси. В дальнейшем свет, соответствующий плюс первому пор дку дифракции, задерживаетс диафрагмой 8, а мииус первый пор док преобразуетс липзой 10 в па)аллельпый пучок света, угол падени которого относительпо оптической оси меп етс во времени . Свет пулевого пор дка дифракции проходит через плоскопараллельную пластипу 9. при этом происходит перенос точки фокусировки в другую плоскость, а именно в ту же, где происходит фокусировка первого дифракционного пор дка. В данном случае смен1ение точки фокусировки происходит па величинуThe analyzed signal is fed to the input of the ultrasonic modulator 5 and simultaneously starts the generator of the chirp signal 6 and the pointing device 13. The hepatore 6 forms a spiral with linear frequency modulation with a duration longer than the modulator 4 delay. When the modulator 4 aperture is filled, the controller The chirp of the si-alo-ma lens output diffraction orders are formed. As far as the passage through the modulator 4 progresses, the first diffraction orders in the direction perpendicular to the optical axis occur. Subsequently, the light corresponding to the plus first diffraction order is delayed by the diaphragm 8, and the first order of the diffractor is converted by the lens 10 into a pa) allele beam of light, the angle of incidence of which is relative to the optical axis is measured in time. The light of the bullet diffraction order passes through the plane-parallel plastip 9. In this case, the focus point is transferred to another plane, namely, to the same one where the first diffraction order is focused. In this case, the focus point changes
где /-длииа пластииы.where / is liaia plastia.
Таким образом, можно, задава определенным образом /, добитьс услови переноса точки фокусировки ну;1евого пор дка.Thus, it is possible, by specifying / in a certain way, to achieve the conditions of transferring the focus point by well; 1st order.
Благодар действию нластины лииза 10 па своем выходе формирует .плоский нучок света и из пучка, соответствующего нулевому пор дку дифракции. Этот лучок Д1вфрагирует па модул торе 5, направление распространени ультразвуковых волн в KOTOpOiM противоположно направлению ультразвуковых воли в модул торе 4, и расщепл етс на р д дифракционных пор дков. Фото.пр|иемник 12 располагаетс в области минус первого дифракцпониого пор дка модул тора 5. Преобразование световой энергии п электрическую происходит в результате и 1терфереиции световых распределений, вызванных .сигналом, и сканируемого светового распределени , сформированного .модул тором 4 II линзой 7 и перепесешюго липзами JO и // в нлоскость регистрации . Максимум э.чектрического сигиалаThanks to the action of a nlizina, the liiza forms a flat light knob from its beam in 10 pa from its output and from a beam corresponding to the zero order of diffraction. This beam diffuses into modulator 5, the direction of propagation of ultrasonic waves in KOTOpOiM is opposite to the direction of ultrasonic waves in modulator 4, and is split into a number of diffraction orders. Photographic terminal 12 is located in the region of minus the first diffraction order of the modulator 5. The conversion of light energy and electrical energy occurs as a result of the light distribution of light distributions caused by the signal and of the scanned light distribution generated by modulator 4 II lens 7 and rescaler JO and // lipz nloskos registration. Maximum of e. Geometric sigial
па выходе фотоприемника наблюдаетс в тот момент, когда иитер|ферирующие пучки колли иеар и ы друг другу. Дл того, чтобы выходные сигналы формировались па высокой частоте, необходимо наметь звукопроводы модул торов пз разных матерналов. Регистраци онсктра сигнала нроизводитс па ппдпкаторпом устройстве J3.The output of the photodetector is observed at the moment when both the primary and secondary beams of the collie and s are in each other. In order for the output signals to be formed at a high frequency, it is necessary to note the sound pipes of modulators of the PS of different materials. The recording of the signal signal is produced by using a J3 device.