При подаче переключателем 23 постоданого отрИцательного напр жени на управл ющий электрод тиристора 1, который при этом открываетс , ток, протекающий через тиристор 1, включает реле 4, которое евоим контактом 13 подключает управл ющий электрод тиристора 2. Цепочка, состо ща из резистора 24 и конденсатора 25, срабатывает только один Раз при подач2 напр жени . Конденсатор 25 зар жаетс , отключа управл ющий электрод тиристора 1.When the switch 23 supplies a post-applied negative voltage to the control electrode of the thyristor 1, which opens in this case, the current flowing through the thyristor 1 switches on the relay 4, which connects the control electrode of the thyristor 2 with its contact 13 and the chain consisting of a resistor 24 and the capacitor 25, triggered only once Once with the supply 2 voltage. The capacitor 25 is charged by disconnecting the control electrode of the thyristor 1.
Дл включени следующей чейки коммутато .ра на обмотку 26 импульсного трансформатора 20 подают импульс с длительностью не менее времени сброса тиристоров.To turn on the next switch cell, a pulse with a duration of at least the thyristor reset time is applied to the winding 26 of the pulse transformer 20.
На обмотках 19 и 22 индуктируютс импульсы той же длительности с амплитудой, равной или несколько большей напр жени питани коммутатора с пол рностью, ноложительной 1на обмотке 22 и отрицательной на обмотке 19 по отношению к шине питани . Пр-и этом напр жение на катодах тиристоров 1, 2, 3 становитс нулевым или положительным по отношению к анодам тиристоров 1, 2, 3, и тиристор 1 выключаетс , отключа питание от обмотки реле 4;On the windings 19 and 22, pulses of the same duration are induced with an amplitude equal to or slightly greater than the supply voltage of the switch with a polarity of 1 at the winding 22 and negative at the winding 19 with respect to the power rail. In this way, the voltage at the cathodes of the thyristors 1, 2, 3 becomes zero or positive with respect to the anodes of the thyristors 1, 2, 3, and the thyristor 1 turns off, turning off the power from the winding of the relay 4;
Тиристор 2 включаетс импульсом, сформированным из заднего фронта импульса обмотки 19 дифференцирующей цепочкой, состо щей из резистора 16, ко«денсатора 18 и диода 17. Включающий импульс приходит через замкнутый контакт 13 реле 4, удерживаемый на врем включени тиристора 2 разр дом конденсатора 7. Ток через тиристор 2 включает реле 5, подключающее управл ющий электрод тиристора 3. При включении тиристора 2 коиденсатор 8 играет роль элемента, замедл ющего включение реле 5. Поэтому подключение управл ющего электрода тиристора 3 к шине питани происходит только при окончании включающего импульса. Далее процессы повтор ютс .The thyristor 2 is switched on by a pulse formed from the back edge of the pulse of the winding 19 by a differentiating chain consisting of a resistor 16 to the capacitor 18 and a diode 17. The starting pulse comes through the closed contact 13 of relay 4 held for the time of the thyristor 2 turned on by the capacitor 7. The current through the thyristor 2 turns on the relay 5 connecting the control electrode of the thyristor 3. When turning on the thyristor 2, the co-sensor 8 plays the role of an element slowing the activation of the relay 5. Therefore, the connection of the control electrode of the thyristor 3 to the power bus occurs only at the end of the trigger pulse. Further, the processes are repeated.