(54) СОШНИК ЛЕСОПОСАДОЧНОЙ МАШИНЫ(54) FORWARDING MACHINE BOWLER
Изобретение относитс к о-бласт.и лесного и сельского хоз йства, а именно к сошникам лесопосадочных машин. Известные коробчатые сошвики, работающие по принципу разрезани и раздвигани почвы, не обеспечивают качественной заделки корневых систем саженцев, так как боковые - стенки посадочных щелей уплотн ютс и деформйруют ко.р.невую систему саженцев; сошник имеет большое т говое сопротивление и невозможно заглубить его на необходимую глубиНу без предварительной подготовки почвы. В основу конструктивного выполнени предлагаемого сошника положен принцид вырезани в почве пласта, разрезани его на две равные части, извлечение этих частей на поверхность с одновременным их оборачиванием , крошением и раздвиганием по сторонам посадочной щели без уплотнени ее стенок. В св зи с этим, в сошнике установлены два дополнительных разрезных ножа, наход щихс по бокам основного разрезного ножа, прикрепленного к боковинам сошника. В нижней части они соединены подрезными ножами, к соторым прикреплены вогнутые пластины, переход щие в отвальные поверхности, ограниченные по ширине боковинами, соединенными между собой снизу днищем, сверху - присоединительной плитой, а внутри них расположена пластина, выполненна в виде направл ющего лотка. Кроме того, лезви всех ножей выполнены сменньши и у разрезных ножей установлены под тупым углом вхождени в почву, а у подрезных - под углом меньше пр мого к направлению движени . На фиг. I изображен сошник в трех проекци х; на фиг. 2--сошник (в аксонометрии) без присоединительной плиты. Сошник состоит из разрезного ножа I, двух дополнительных разрезных ножей 2, которые прикреплены к боковинам 3 и двух вогнутых пластин 4, переход щих в отвальные поверхности , началом которых служат подрезные ножи 5. Вс конструкци сверху жестко св зана присоединительной плитой б, служащей дл креплени сошника к раме машины. Боковины снизу св заны с днищем 7, а внутри них расположена пластина, выполненна в виде направл ющего лотка 8, и св зывающа между собой боковины и днище. В промежутке между дополнительными разрезными ножами и отвальной поверхностью боковины выполнены на высоту начала поверхности отваливани , причем в боковинах, ограниченных сверху присоединительной плитой и рамой .машины, образуютс окна 9, через которые вырезаемые пласты почвы отваливаютс в стороны от щели.FIELD: forestry and agriculture, in particular, to the coulters of forest planting machines. The well-known box-shaped coulters, working on the principle of cutting and pushing the soil apart, do not provide high-quality embedment of root systems of seedlings, since the lateral walls of the planting slots are compacted and deform the co-rn seed system of seedlings; The coulter has a large traction resistance and it is impossible to dig it into the required depth without preparing the soil. The constructive implementation of the proposed coulter is based on the principle of cutting a layer in the soil, cutting it into two equal parts, extracting these parts to the surface with their simultaneous wrapping, crushing and moving apart on the sides of the landing slot without sealing its walls. In this connection, two additional split knives are installed in the opener, which are located on the sides of the main split knife attached to the side openings of the opener. In the lower part, they are connected by cutting knives, to which concave plates are attached, which pass into dumping surfaces, limited in width by side walls, interconnected by the bottom, on top of the connecting plate, and inside them is a plate made in the form of a guide tray. In addition, the blades of all knives were replaced and, at split knives, were installed at an obtuse angle of entry into the soil, and at cuttings, at an angle less than direct to the direction of movement. FIG. I depicts a vomer in three projections; in fig. 2 - opener (in axonometry) without connecting plate. The opener consists of a split knife I, two additional split knives 2, which are attached to the sidewalls 3 and two concave plates 4, which are turned into dumping surfaces, starting with cutting knives 5. The entire structure is rigidly connected from above with a connecting plate b used for fastening Vomer to the frame of the machine. The sidewalls at the bottom are connected to the bottom 7, and inside them there is a plate, made in the form of a guide chute 8, and the interconnecting sidewalls and the bottom. In the gap between the additional split blades and the lateral surface of the sidewall are made to the height of the beginning of the roll surface, and in the sidewalls bounded above by the connecting plate and machine frame, windows 9 are formed through which the cut layers of soil fall off to the side of the slit.
При движении .машины ножи 1, 2, 5 вырезают из почвы два пласта. Подъемно-отвальные поверхности поднимают их вверх, оборачивают , разрушают раздвигают в стороны от посадочной щели. При этом боковины 3 удерживают стенки щели от засыпани до посадки растений, корнева система которых опускаетс в Щель по лотку 8. Следующие за сошниКО .М известные элементы машины заделывают корневую систему высаженных растений окончательно . Дл более качественного резани почвы и различных включений в ней все ножи выполнены оменны;ми, причем разрезные ножи установлены под углом f 90°, а подрезные - с общим углом p.acTiBOpa, от 90° ; а 180°.When moving machines, knives 1, 2, 5 cut out two layers from the soil. Lifting-dump surfaces lift them up, wrap, destroy, push them to the side of the landing slot. In this case, the sidewalls 3 keep the walls of the slit from falling asleep before planting, the root system of which is lowered into the Slit along the chute 8. The following machine parts follow the root system of the transplanted plants definitively. For better cutting of the soil and various inclusions in it, all the knives are made omenny, and the split knives are set at an angle of 90 °, and the undercutting are from a total angle of p.acTiBOpa, from 90 °; a 180 °.
Предмет изобретени Subject invention