Известны устрой-ствл дл каисуллроваип пазов статора эле-ктргческой MaiHiiiiu нреим ществе-мю ферромагиитиой диэлектрической массой (Ф.Д.М), в .которых нодача массы осуществл етс к торцовой иоверхиости статора . Дл механизации ироиеоса и новышени качества издели иредлагаемое устройство содержит вводимое в расто-Ч1ку статора ирисиособление дл подачи .массы в пазы, вылолнеикое в в.иде иилиндр;гческого стакана, св занного с .вибратором и имеющего в боковой стеиКе отверсти по числу назов ка1исул 1руеMOiio статора, а также расг оложенНого в нем иорши . Дно рабочей полости стакана и рабочи конец иорпш выноднены конусными. Отверсти в сте}же ста1ка«а могут быть расположены иа разНых по высоте уровн х. На чертеже схе матично иоказаи один из вариантов вытюлнени описываемого устройства , вертикальный разрез. Устройство расположено на механическом вибрационном столе 1 с вибраторами, устано-влонньвми на .ртизаторах. В.гбратор 2 состоит из .подвески и тре.хскоростного двигател с экспеитрика.ми на двух свобод иых концах вала и совершает направленные колебани . На BnSpaiuioHHOM столе укреплен цилиндрический стакан 3. В полость стакана вводитс ферромагн ггна д;1алектрическа масса 4, постуиаюищ в иазы статора ,5 асин .хропиого .двигател через отверсти а. выиолиенные по окружности cTauaiia против каждого иаза. Сверху расиоложе; иоршепь 6 с дополнительным грузом 7. Уилот-11еии 8 из вахуумной резины на торцах статора предохраи ют от вытекани массы в лобовые части. На степень унлотнепи массы больн.юе вли ние оказывают .илитyдa ii частота колебаний вибратора. Дл каждой частоты существует определеииа .амплитуда колебаний, при которой г.аиболее уффект;1вно вибр)ровать смесь. Наилучп1е1 1 частото вл етс частота 45-60 Гц при амг,литуде 0,6-1,2 .и. ВибраЦ;1Я не только уг.лотн ет массу, )io и по .могает получить гладкую i ровную иове-рхность клиньев 3 .расточкс статора. Поршень 6 с грузом rie должен иметь жесткой св зи с В-1братором 2. а стакаи .) со статором 5 необходимо жестко креи1ггь к У, так кал то.чько в этом случае оии не иодирыгнвают . (;бесиечива возможность умео1ьц ени частоты колебаиий i увеличени амаьт} туды . Таким образом, колебани от вибрато - ;; иолностыо .нередаютс массе. Нсли иазы статора имеют больн1ую длину, то мг:ссы можно осуществл ть с ссрсди1Г1 )1 пакета или же встречно с двух по сов, ломпеиснру чтим недостаточную глубн1г.There are known devices for sticking grooves of a stator by an electric MaiHiiiiu, particularly ferromagitic dielectric mass (F.D.M), in which the nodach mass is applied to the end face of the stator. For the mechanization of iroeeos and the improvement of product quality, the proposed device contains an irradiation device introduced into the stator of the stator to feed the mass into the grooves, in the form of or in the form of a glass, connected to the vibrator and having holes in the side pattern in the number of body pattern and the number it has. the stator, as well as the iorshi dissolved in it. The bottom of the working cavity of the glass and the working end of the irons are made conical. Holes in the stack of the same station may be located at levels different in height. In the drawing is a schematic diagram and one of the options for extracting the described device, a vertical section. The device is located on a mechanical vibrating table 1 with vibrators mounted on the grabers. B. The gbrator 2 consists of suspensions and a three-speed engine with experiments on two free ends of the shaft and makes directed oscillations. On the BnSpaiuioHHOM table a cylindrical cup 3 is fixed. Into the cup cavity, a ferromagnetic cup is inserted; a electrical mass of 4 is applied to the stator, 5 asyn. Throat motors through the holes a. circumferentially circumscribed cTauaiia against each iaz. Above, rational; Figure 6 with additional load 7. The Wilot 11eii 8 of vacuum rubber at the ends of the stator is protected from the outflow of mass into the frontal parts. The degree of unlotnepi mass of the patient is affected by the. Or frequency ii vibrator oscillation frequency. For each frequency, there is a determination of the amplitude of oscillations at which the most effect is; The best frequency is the frequency of 45-60 Hz with amg and volume of 0.6-1.2. Vibration; 1I not only increases the mass, io, and helps to get a smooth and even wedge-like structure of wedges 3. The center stator. A piston 6 with a load of rie must have a rigid connection with the B-1 bractor 2. a stack.) With the stator 5, it is necessary to firmly attach to U, so it doesn’t indignate in this case. (; reckoning the possibility of increasing the frequency of oscillations i increasing amatud). Thus, vibrations from vibrato are not; mass; stator stasis is of a sickle length, then mg: ss can be done with srccd1H1) 1 packet or from two to ten, lompuy is in honor of the lack of depth.