ливземого регул тором 29 и контролируемого по манометру 15. Сохранению разных давлений в полост х коллекторов 10 и 12 способствует обратный клапан 17.check valve 29 and controlled by a pressure gauge 15. The check valve 17 contributes to the maintenance of different pressures in the cavities of the collectors 10 and 12.
После определенной выдержки испытуемых рукавов под давлением и их осмотра на пульте управлени нажимаетс кнопка Слив жидкости. При этом срабатывают электропневмоклапаны 25 и 30 и отключаетс насосна установка 3. Электропневмок- лапан 30 соедин ет воздушную полость клапана 14 с атмосферой, в результате чего под давлением пружин клапан открываетс и не преп тствует сливу жидкости из системы , а электропневмоклапан 25 соедин ет воздушные полости пневмогидроаккумул - тора 5 и клапана 26 с атмосферой, открыва тем самым клапан 26. Одновременно с этим сжатый воздух от электропневмоклапана 25 через обратный клапан 24 подаетс в полость А коллектора 10 и проходит далее по системе, вытесн наход щуюс в ней жидкость в бак 4,After a certain exposure of the test sleeves under pressure and their inspection on the control panel, the Liquid drain button is pressed. In this case, the electro-pneumatic valves 25 and 30 are triggered and the pump unit 3 is turned off. The electro-pneumatic valve 30 connects the air cavity of the valve 14 to the atmosphere, as a result of which, under the pressure of the springs, the valve opens and does not prevent fluid from draining from the system, and the electro-pneumatic valve 25 connects the air cavities a pneumatic accumulator 5 and a valve 26 with atmosphere, thereby opening the valve 26. At the same time, compressed air from the electro-pneumatic valve 25 through the check valve 24 is supplied to the cavity A of the manifold 10 and then passes through the systems Expelling Nachod schuyus therein liquid to the tank 4,
По окончании слива жидкости и последующей продувки системы сжатым воздухом , нажимаетс кнопка Стоп, в результате чего срабатывает электропневмоклапан 28 и перекрывает поступление сжатого воздуха в пневмосистему 6. Испытуемые издели снимаютс со стола 1, а полость пневмогидроаккумул тора 5 в это врем по линии 27 заполн етс жидкостью из бака 4 до совпадени с уровнем жидкости в баке, подготавлива тем самым устройст-1 во дл испытани следующих изделий.At the end of the fluid drain and the subsequent purging of the system with compressed air, the Stop button is pressed, as a result of which the electro-pneumatic valve 28 is triggered and the compressed air supply to the pneumatic system 6 is shut off. The test products are removed from table 1, and the pneumatic accumulator cavity 5 is filled through line 27 at this time liquid from the tank 4 to match the liquid level in the tank, thereby preparing the device 1 for testing the following products.
Использование предложенного устройства позвол ет производить одновременное испытание изделий под различными давлени ми, что расшир ет его технологические возможности и в 1,6...1,9 раза повышает производительность испытаний за счет совмещени во времени заполнени системы, выдержки изделий под давлением и слива жидкости при испытании изделий низким и высоким давлением.Using the proposed device allows simultaneous testing of products at different pressures, which expands its technological capabilities and increases 1.6 ... 1.9 times the test performance by combining the filling time of the system, holding the products under pressure and draining the liquid when testing products low and high pressure.