Gebrauchsmuster-Anmeldung Meßvorrichtung für Stahlbandringe Die Schwierigkeit
des Nachmessens der Bandbreite bei kalten Bandstahlringen besteht darin, daß ein
Nachmessen nur dann möglich war, wenn der Bandstahlring, umgewickelt wurde. Utility model registration Measuring device for steel band rings The difficulty
the re-measurement of the band width with cold steel band rings consists in the fact that a
Re-measuring was only possible if the steel band ring was wrapped around.
Diesem Nachteil begegnet nun die Meßvorrichtung gemäß der Neuerung
dadurch, daß mindestens ein Haftmagnet über eine Schraubklemme
mit
einem Meßstab in Verbindung steht, an dessen einem Ende ein
Meßbügel
, drehbar angebracht ist, während ein weiterer, auf dem Meßstab
ver-
leßspitze verse-
schieb-und drehbarer Meßbügel, ebenfalls mit einer Meßspitze
verse-
hen, in seinem Führungsstück eine an sich bekannte Noniuseinteilung
''
zeigt.
Der besondere Vorteil dieser Lösung liegt darin, daß die Meßvorrich-
tung fest auf dem Bandstahlring haftet und die Prüfer nunmehr beide Hände für den
Meßvorgang selbst frei haben. Für jede gewünschte Umdre-' ung innerhalb des Bandstahlringes
kann in denkbar einfacher und
1 zweckmäßiger Weise durch einfaches Heranschieben des einen
Meßbügels
;
an die entsprechende Bandkante wie bei einer Schieblehre die
Breite
, am Meßstab mittels des Nonius abgelesen werden.
In der Abbildung ist die Neuerung als Ausführungsbeispiel schematisch dargestellt.
I
Ein Meßstab 1 führt an seinem einen Ende einen um die Längsachse des Meßstabes 1
drehbaren, nicht verschiebbaren Meßbügel 2, der an seinem . freien Ende eine Meßspitze
3 trägt. Ein weiterer Meßbügel 4, gleichfalls drehbar, jedoch auf dem Meßstab 1
verschiebbar angeordnet, und mit einer Meßspitze 3 ausgestattet, zeigt in seinem
Führungsstück 5 eine Noniuseinteilung 6 in an sich bekannter Weise für das Ablesen
der gemessenen Breite eines nicht dargestellten Bandes. Auf dem Meßstab 1 sind eine
oder mehrere verschiebbare Schraubklemmen 7 vorge-'sehen, die mit einem oder mehreren
Haftmagneten 8 verbunden sind. Die Anzahl der Haftmagneten 8 richtet sich nach der
Breite des Bandes.The measuring device according to the innovation now counteracts this disadvantage in that at least one holding magnet has a screw terminal with
a dipstick is in connection, at one end of which a measuring bracket
, is rotatably attached, while another, on the dipstick
leßspitze verse
sliding and rotating measuring frame, also with a measuring tip
hen, a well-known vernier scale in its guide piece
''
shows.
The particular advantage of this solution is that the measuring device
device adheres firmly to the steel strip ring and the testers now have both hands free for the measuring process themselves. For every desired rotation within the steel strip ring, it is very easy and 1 expediently by simply pushing one measuring bracket
;
the width of the corresponding tape edge as with a caliper
, can be read on the dipstick using the vernier.
In the figure, the innovation is shown schematically as an exemplary embodiment. I.
A measuring stick 1 leads at one end to a rotatable about the longitudinal axis of the measuring stick 1, non-displaceable measuring bracket 2, which at his. free end carries a measuring tip 3. Another measuring bracket 4, also rotatable but slidable on the measuring stick 1, and equipped with a measuring tip 3, shows a vernier scale 6 in its guide piece 5 in a manner known per se for reading the measured width of a band, not shown. One or more displaceable screw terminals 7, which are connected to one or more holding magnets 8, are provided on the measuring stick 1. The number of holding magnets 8 depends on the width of the tape.