<Desc/Clms Page number 1>
Blitzlichtlampe.
EMI1.1
<Desc/Clms Page number 2>
EMI2.1
Als Füllung dienen bekannte Zünds tze. Am besten werden solche genommen, die verhältnis- mässig wenig Gas, aber ausserordentlich grosse Flammtemperatur entwickeln, wie z. B. eine Mischung von Phosphor mit Antimontrioxyd, Phosphor oder Schwefel mit Mennige usw.
In Fig. 2 besteht der Behälter 1 fast ganz aus Metall. Nur oben ist eine lichtdurchlässige Kappe 10 aufgekittet. Am Zündhütehen ist der Wandungsteil 9 ausgestülpt, so dass er harmonikaartig zusammen- gedrückt werden kann, wodurch die Zündung besonders leicht und sicher erfolgt. Ein Stift oder Bolzen 7 wird mittels einer Hebelvorrichtung 11, die um eine Achse 12 drehbar angeordnet ist, in die Kappenwand hineingedrückt. Die ganze Hebelvorrichtung ist in einer besonderen Hülse 13 befestigt. Man kann so die Lampe bequem in die Hülse einstecken, in der Hand halten und mit einem Finger den Knopf 6 betätigen.
Gemäss Fig. 3 wird die an der Kappe angebrachte, dem Zündhütchen entsprechende Ausbauchung 9 mittels eines seitlich dagegen drückenden Bolzens 7, der in einer Führung 17 sitzt, eingedrückt und die Zündung bewirkt.
Bei der Ausführungsform nach Fig. 4 ist an der Kappe eine Ausstülpung 18 angebracht. Seitlich von dieser sitzt das Zündhütchen 9. Es wird wieder mittels eines Stiftes 7 betätigt, der in die Wandung einer Hülse 13 eingelassen ist. Der Flammkanal 19 ist gegen das Lampeninnere zu gerichtet.
Das Pumprohr 3 aus Glas, Bakelit, Metall od. dgl. kann auch mit Vorteil an die Kappe angesetzt sein. Es kann auch gleich bei der Herstellung aus dem Material der Kappe herausgepresst werden. Man dichtet es so ab, dass man einen Einsatz 15 etwa aus Picein an einer gegebenenfalls vorgesehenen Ein- schnürung 16 erwärmt, wodurch sich die Öffnung verstopft. Auch kann man das Rohr unter Erwärmung zusammenpressen.
Gemäss Fig. 5 ist eine weitere Vereinfachung dadurch geschaffen, dass das Pumprohr 3 zur Aufnahme eines das Zündhütchen 5 tragenden, deformierbaren Einsatzes 4 dient. Vor dem Anschluss des Rohres 3 an die Vakuumleitung wird der Einsatz 5 gasdurchlässig eingesetzt, d. h. die Luft kann am Einsatz 4 vorbei abgesaugt und die Gasfüllung eingelassen werden. Der Einsatz ist nun mit einem Mantel aus einem erweichbaren Dichtungsmittel 20 wie Picein, weisses Siegellack usw. versehen. Der Einsatz kann sogar ganz oder teilweise aus erweichbarem Material bestehen. Durch leichte Erwärmung verklebt das Dichtungsmittel den bestehenden schmalen, in der Figur übertrieben weit dargestellten Spalt vakuumdicht. Der überschüssige Teil des Pumprohres 3 kann dann abgesprengt werden.
PATENT-ANSPRÜCHE :
1. Blitzlichtlampe mit in einem geschlossenen, vorzugsweise ganz oder teilweise evakuierten und
EMI2.2
starre, unverbrennbare und gasdichte Kolbenwandung zumindest an einer Stelle zum Zwecke der Entzündung durch äussere mechanische Einwirkung biegsam oder dehnbar ausgebildet ist.
<Desc / Clms Page number 1>
Flash lamp.
EMI1.1
<Desc / Clms Page number 2>
EMI2.1
Well-known ignition charges are used as filling. It is best to choose those which develop relatively little gas but an extraordinarily high flame temperature, e.g. B. a mixture of phosphorus with antimony trioxide, phosphorus or sulfur with red lead, etc.
In Fig. 2, the container 1 consists almost entirely of metal. A translucent cap 10 is cemented on only at the top. The wall part 9 is turned out at the primer cap so that it can be pressed together like a harmonica, whereby the ignition takes place particularly easily and safely. A pin or bolt 7 is pressed into the cap wall by means of a lever device 11 which is arranged to be rotatable about an axis 12. The entire lever device is fastened in a special sleeve 13. You can easily insert the lamp into the sleeve, hold it in your hand and press button 6 with one finger.
According to FIG. 3, the bulge 9 attached to the cap and corresponding to the primer cap is pressed in by means of a bolt 7 which is laterally pressed against it and sits in a guide 17, and ignition is effected.
In the embodiment according to FIG. 4, a protuberance 18 is attached to the cap. The primer 9 is seated to the side of this. It is actuated again by means of a pin 7 which is embedded in the wall of a sleeve 13. The flame channel 19 is directed towards the interior of the lamp.
The pump tube 3 made of glass, Bakelite, metal or the like can also advantageously be attached to the cap. It can also be pressed out of the material of the cap during manufacture. It is sealed in such a way that an insert 15 made of picein, for example, is heated at an optionally provided constriction 16, whereby the opening is blocked. You can also press the pipe together while heating.
According to FIG. 5, a further simplification is created in that the pump tube 3 serves to receive a deformable insert 4 carrying the primer cap 5. Before the pipe 3 is connected to the vacuum line, the insert 5 is inserted in a gas-permeable manner; H. the air can be sucked off past the insert 4 and the gas filling can be admitted. The insert is now provided with a jacket made of a softenable sealant 20 such as Picein, white sealing wax, etc. The insert can even consist entirely or partially of softenable material. By slightly heating the sealant, the existing narrow gap, which is shown in an exaggerated manner in the figure, is vacuum-tight. The excess part of the pump tube 3 can then be blown off.
PATENT CLAIMS:
1. Flash lamp with in a closed, preferably fully or partially evacuated and
EMI2.2
rigid, incombustible and gas-tight piston wall is designed to be flexible or expandable at least at one point for the purpose of ignition by external mechanical action.