<Desc/Clms Page number 1>
KARL SCHAUKAL m WIEN. Verschluss für Flaschen und Gefässe.
Dieser Verschluss besteht aus zwei ineinander greifenden Teilen, wovon einer d4 besonders geformte Stöpsel selbst ist, der andere im Halse der Flasche oder am obere inneren Rande des Gefässes angebracht ist und aus demselben Materiale als diese besteh
EMI1.1
einem Stück gearbeitet, wird mit diesen schon gegossen. Bei Flaschen oder Gefässen at Blech u. dgl. ist dieser Teil an der betreffenden Stelle anzulöten.
Der im Halse der Flasche oder am oberen inneren Rande des Gefässes angebracht Teil a besteht aus einem schiefen, kegelförmigen, mit der Spitze nach aufwärts gerichtet Ansatz, welcher mit der inneren Wand des Flaschenhalses eine Rinne b bildet, wel ( letztere in sich selbst verlauft. Die schiefe Lage ist deshalb gewählt, damit die in d < Rinne sich ansammelnde Flüssigkeit nach unten ablaufen kann, zu welchem Zwecke e dem tiefsten Punkte der Rinne sich eine kleine Ausnehmung befindet.
Der Stöpsel besitzt an seiner unteren Seite eine der Form des Ansatzes a en sprechende Ausnehmung d, mit einem der Ausnohmung c im Flaschenhalse entsprechend@ Ansatze e, so dass die beiden Verschlussteile beim Ineinanderschieben vollständig ineinand greifen und dadurch einen sicheren Verschluss herstellen (Fig. 5).
Am oberen Rande des Flaschenhalses ist ein cylindrischer Ansatz ; mit halbkrei förmigem Querschnitt und an der korrespondierenden Stelle des Stöpsels ein ähnlich ! Ansatz f vorgesehen, an welch letzterem ein Karabinerhaken 9 befestigt ist, dessen hake förmigcr Schuber im geschlossenen Zustande um den Ansatz lu greift und so den Stöps in der Flasche festhält.
Bei Gefässen mit weiten Öffnungen können zwei solche Haken an zwei gegenüber liegenden Stellen angebracht werden.
**WARNUNG** Ende DESC Feld kannt Anfang CLMS uberlappen**.
<Desc / Clms Page number 1>
KARL SCHAUKAL in VIENNA. Closure for bottles and jars.
This closure consists of two interlocking parts, one of which is a specially shaped stopper itself, the other is attached in the neck of the bottle or on the upper inner edge of the vessel and is made of the same material as this
EMI1.1
worked in one piece, these are already cast. For bottles or jars at sheet metal u. This part is to be soldered at the relevant point.
The part a attached in the neck of the bottle or on the upper inner edge of the vessel consists of an oblique, conical, with the tip pointing upwards, which forms a groove b with the inner wall of the bottle neck, the latter running in itself. The inclined position is chosen so that the liquid that collects in the channel can drain downwards, for which purpose there is a small recess at the lowest point of the channel.
On its lower side, the stopper has a recess d corresponding to the shape of the projection a, with a recess e corresponding to the recess c in the bottle neck, so that the two closure parts completely interlock when they are pushed into one another and thereby create a secure closure (Fig. 5 ).
At the upper edge of the bottle neck is a cylindrical approach; with a semicircular cross-section and a similar one at the corresponding point of the plug! Approach f provided, to which the latter a snap hook 9 is attached, the hook-shaped slipcase of which engages around the approach lu in the closed state and thus holds the stopper in the bottle.
For vessels with wide openings, two such hooks can be attached to two opposite positions.
** WARNING ** End of DESC field may overlap beginning of CLMS **.