add Low-Power demo

esp8266 · devyte · Feb 2, 2020 · Jan 6, 2020 · Jan 6, 2020 · Jan 9, 2020
commit 287bc2d1029475a4b28bd817459f0872a07c4b9f
diff --git a/libraries/esp8266/examples/LowPowerDemo/LowPowerDemo.ino b/libraries/esp8266/examples/LowPowerDemo/LowPowerDemo.ino
@@ -0,0 +1,365 @@
+/* This example demonstrates the different low-power modes of the ESP8266
+
+   My initial setup was a WeMos D1 Mini with 3.3V connected to the 3V3 pin through a meter
+   so that it bypassed the on-board voltage regulator and USB chip.  There's still about
+   0.3 mA worth of leakage current due to the unpowered chips, so an ESP-01 will show lower
+   current readings than what I could achieve.  These tests should work with any module.
+   While the modem is on the current is 67 mA or jumping around with a listed minimum.
+   To verify the 20 uA Deep Sleep current I removed the voltage regulator and USB chip.
+
+   Since I'm now missing the USB chip, I've included OTA upload.  You'll need to upload
+   from USB or a USB-to-TTL converter the first time, then you can disconnect and use OTA
+   afterwards during any test if the WiFi is connected.  Some tests disconnect or sleep WiFi
+   so OTA won't go through.  If you want OTA upload, hit RESET & press the test button once.
+
+   This test assumes you have a pushbutton switch connected between D3 and GND to advance
+   the tests.  You'll also need to connect D0/GPIO16 to RST for the Deep Sleep tests.
+   If you forget to connect D0 to RST it will hang after the first Deep Sleep test.
+   Connect an LED from any free pin through a 330 ohm resistor to the 3.3V supply, NOT the 3V3
+   pin on the module or it adds to the measured current.  When it blinks you can proceed.
+   When the LED is lit continuously it's connecting WiFi, when it's off the CPU is asleep.
+   The LED blinks slowly when the tests are complete.
+
+   WiFi connections will be made over twice as fast if you can use a static IP address.
+
+   This example code is in the public domain, and was inspired by code from numerous sources */
+
+#include <ESP8266WiFi.h>
+#include <ESP8266mDNS.h>
+#include <WiFiUdp.h>
+#include <ArduinoOTA.h>
+#include <PolledTimeout.h>
+
+//#define DEBUG  // prints WiFi connection info to serial, uncomment if you want WiFi messages
+#ifdef DEBUG
+#define DEBUG_PRINTLN(x)  Serial.println(x)
+#define DEBUG_PRINT(x)  Serial.print(x)
+#else
+#define DEBUG_PRINTLN(x)
+#define DEBUG_PRINT(x)
+#endif
+
+#define WAKE_UP_PIN D3  // GPIO0, can also force a serial flash upload with RESET
+
+// un-comment one of the two lines below for your LED connection
+#define LED D1  // external LED for modules with built-in LEDs so it doesn't add to the current
+//#define LED D4  // GPIO2 LED for ESP-01,07 modules; D4 is LED_BUILTIN on most other modules
+
+ADC_MODE(ADC_VCC);  // allows us to monitor the internal VCC level; it varies with WiFi load
+// don't connect anything to the analog input pin(s)!
+
+// enter your WiFi configuration below
+const char* AP_SSID = "SSID";  // your router's SSID here
+const char* AP_PASS = "password";  // your router's password here
+IPAddress staticIP(0, 0, 0, 0); // parameters below are for your static IP address, if used
+IPAddress gateway(0, 0, 0, 0);
+IPAddress subnet(0, 0, 0, 0);
+IPAddress dns1(0, 0, 0, 0);
+IPAddress dns2(0, 0, 0, 0);
+
+
+// CRC function used to ensure data validity of RTC User Memory
+uint32_t calculateCRC32(const uint8_t *data, size_t length);
+
+// This structure will be stored in RTC memory to remember the reset loop count.
+// First field is CRC32, which is calculated based on the rest of the structure contents.
+// Any fields can go after the CRC32.  The structure must be 4-byte aligned.
+struct {
+  uint32_t crc32;
+  byte data[4];  // the last byte stores the reset count
+} rtcData;
+
+byte resetLoop = 0;  // keeps track of the number of Deep Sleep tests / resets
+String resetCause = "";
+
+const unsigned int blinkDelay = 100; // fast blink rate for the LED when waiting for the user
+const unsigned int longDelay = 350;  // longer delay() for the two AUTOMATIC modes
+esp8266::polledTimeout::periodicFastMs blinkLED(blinkDelay);
+// use fully qualified type and avoid importing all ::esp8266 namespace to the global namespace
+
+void wakeupCallback() {  // unlike ISRs, you can do a print() from a callback function
+  Serial.println(F("Woke from Forced Light Sleep - this is the callback"));
+}
+
+void setup() {
+  pinMode(LED, OUTPUT);  // Activity and Status indicator
+  digitalWrite(LED, LOW);  // turn on the LED
+  pinMode(WAKE_UP_PIN, INPUT_PULLUP);  // polled to advance tests, INTR for Forced Light Sleep
+  Serial.begin(115200);
+  Serial.print(F("\nReset reason = "));
+  String resetCause = ESP.getResetReason();
+  Serial.println(resetCause);
+  if (resetCause == "External System") {
+    Serial.println(F("I'm awake and starting the low power tests"));
+    resetLoop = 5;
+    updateRTC();  // if external reset, wipe the RTC memory and start all over
+  }
+
+  // Read struct from RTC memory
+  if (ESP.rtcUserMemoryRead(64, (uint32_t*) &rtcData, sizeof(rtcData))) {
+    uint32_t crcOfData = calculateCRC32((uint8_t*) &rtcData.data[0], sizeof(rtcData.data));
+    if (crcOfData != rtcData.crc32) {  // if the CRC is invalid
+      resetLoop = 0;  // set first test loop since power on or external reset
+    } else {
+      resetLoop = rtcData.data[3];  // read the previous reset count
+    }
+  }
+}  // end of Setup()
+
+void loop() {
+  if (resetLoop == 0) {
+    // 1st test - running with WiFi unconfigured, reads ~67 mA minimum
+    Serial.println(F("\n1st test - running with WiFi unconfigured"));
+    float volts = ESP.getVcc();
+    Serial.printf("The internal VCC reads %1.3f volts\n", volts / 1000 );
+    Serial.println(F("press the button to continue"));
+    waitPushbutton(false, blinkDelay);
+
+    // 2nd test - Automatic Modem Sleep 7 seconds after WiFi is connected (LED flashes)
+    Serial.println(F("\n2nd test - Automatic Modem Sleep"));
+    Serial.println(F("connecting WiFi, please wait until the LED blinks"));
+    init_WiFi();
+    init_OTA();
+    Serial.println(F("The current will drop in 7 seconds."));
+    volts = ESP.getVcc();
+    Serial.printf("The internal VCC reads %1.3f volts\n", volts / 1000 );
+    Serial.println(F("press the button to continue"));
+    waitPushbutton(true, longDelay);
+
+    // 3rd test - Forced Modem Sleep
+    Serial.println(F("\n3rd test - Forced Modem Sleep"));
+    WiF
9E88
i.forceSleepBegin();
+    delay(10);  // it doesn't always go to sleep unless you delay(10)
+    volts = ESP.getVcc();
+    Serial.printf("The internal VCC reads %1.3f volts\n", volts / 1000 );
+    Serial.println(F("press the button to continue"));
+    waitPushbutton(false, blinkDelay);
+
+    // 4th test - Automatic Light Sleep
+    Serial.println(F("\n4th test - Automatic Light Sleep"));
+    Serial.println(F("reconnecting WiFi"));
+    Serial.println(F("it will be in Automatic Light Sleep once WiFi connects (LED blinks)"));
+    digitalWrite(LED, LOW);  // visual cue that we're reconnecting
+    WiFi.setSleepMode(WIFI_LIGHT_SLEEP, 5);  // Automatic Light Sleep
+    WiFi.forceSleepWake();  // reconnect with previous STA mode and connection settings
+    while (!WiFi.localIP())
+      delay(50);
+    volts = ESP.getVcc();
+    Serial.printf("The internal VCC reads %1.3f volts\n", volts / 1000 );
+    Serial.println(F("press the button to continue"));
+    waitPushbutton(true, longDelay);
+
+    // 5th test - Forced Light Sleep using Non-OS SDK calls
+    Serial.println(F("\n5th test - Forced Light Sleep using Non-OS SDK calls"));
+    WiFi.mode(WIFI_OFF);  // you must turn the modem off; using disconnect won't work
+    yield();
+    digitalWrite(LED, HIGH);  // turn the LED off so they know the CPU isn't running
+    volts = ESP.getVcc();
+    Serial.printf("The internal VCC reads %1.3f volts\n", volts / 1000 );
+    Serial.println(F("CPU going to sleep, pull WAKE_UP_PIN low to wake it (press the button)"));
+    delay(100);  // needs a brief delay after the print or it may print the whole message
+    wifi_fpm_set_sleep_type(LIGHT_SLEEP_T);
+    gpio_pin_wakeup_enable(GPIO_ID_PIN(WAKE_UP_PIN), GPIO_PIN_INTR_LOLEVEL);
+    // only LOLEVEL or HILEVEL interrupts work, no edge, that's an SDK or CPU limitation
+    wifi_fpm_set_wakeup_cb(wakeupCallback); // Set wakeup callback (optional)
+    wifi_fpm_open();
+    wifi_fpm_do_sleep(0xFFFFFFF);  // only 0xFFFFFFF allowed; any other value and it won't sleep
+    delay(10);  // it goes to sleep some time during this delay() and waits for an interrupt
+    Serial.println(F("Woke up!"));  // the interrupt callback hits before this is executed
+
+    // 6th test - Deep Sleep for 10 seconds, wake with RF_DEFAULT
+    Serial.println(F("\n6th test - Deep Sleep for 10 seconds, wake with RF_DEFAULT"));
+    init_WiFi();  // initialize WiFi since we turned it off in the last test
+    init_OTA();
+    resetLoop = 1;  // advance to the next Deep Sleep test after the reset
+    updateRTC();  // save the current test state in RTC memory
+    volts = ESP.getVcc();
+    Serial.printf("The internal VCC reads %1.3f volts\n", volts / 1000 );
+    Serial.println(F("press the button to continue"));
+    while (!digitalRead(WAKE_UP_PIN))  // wait for them to release the button from the last test
+      delay(10);
+    delay(50);  // debounce time for the switch, button released
+    waitPushbutton(false, blinkDelay);
+    digitalWrite(LED, LOW);  // turn the LED on, at least briefly
+    Serial.println(F("going into Deep Sleep now..."));
+    delay(10);  // sometimes the \n isn't printed without a short delay
+    ESP.deepSleep(10E6, WAKE_RF_DEFAULT); // good night!  D0 fires a reset in 10 seconds...
+    delay(10);
+    // if you do ESP.deepSleep(0, mode); it needs a RESET to come out of sleep (RTC is off)
+    // maximum timed Deep Sleep interval = 71.58 minutes with 0xFFFFFFFF
+    // the 2 uA GPIO current during Deep Sleep can't drive the LED so it's off now
+    Serial.println(F("What... I'm not asleep?!?"));  // it will never get here
+  }
+
+  // 7th test - Deep Sleep for 10 seconds, wake with RFCAL
+  if (resetLoop < 4) {
+    init_WiFi();  // need to reinitialize WiFi & OTA due to Deep Sleep resets
+    init_OTA();   // since we didn't do it in setup() because of the first test
+  }
+  if (resetLoop == 1) {  // second reset loop since power on
+    resetLoop = 2;  // advance to the next Deep Sleep test after the reset
+    updateRTC();  // save the current test state in RTC memory
+    Serial.println(F("\n7th test - in RF_DEFAULT, Deep Sleep for 10 seconds, wake with RFCAL"));
+    float volts = ESP.getVcc();
+    Serial.printf("The internal VCC reads %1.3f volts\n", volts / 1000 );
+    Serial.println(F("press the button to continue"));
+    waitPushbutton(false, blinkDelay);
+    Serial.println(F("going into Deep Sleep now..."));
+    delay(10);  // sometimes the \n isn't printed without a short delay
+    ESP.deepSleep(10E6, WAKE_RFCAL); // good night!  D0 fires a reset in 10 seconds...
+    delay(10);
+    Serial.println(F("What... I'm not asleep?!?"));  // it will never get here
+  }
+
+  // 8th test - Deep Sleep Instant for 10 seconds, wake with NO_RFCAL
+  if (resetLoop == 2) {  // third reset loop since power on
+    resetLoop = 3;  // advance to the next Deep Sleep test after the reset
+    updateRTC();  // save the current test state in RTC memory
+    Serial.println(F("\n8th test - in RFCAL, Deep Sleep Instant for 10 seconds, wake with NO_RFCAL"));
+    float volts = ESP.getVcc();
+    Serial.printf("The internal VCC reads %1.3f volts\n", volts / 1000 );
+    Serial.println(F("press the button to continue"));
+    waitPushbutton(false, blinkDelay);
+    Serial.println(F("going into Deep Sleep now..."));
+    delay(10);  // sometimes the \n isn't printed without a short delay
+    ESP.deepSleepInstant(10E6, WAKE_NO_RFCAL); // good night!  D0 fires a reset in 10 seconds...
+    delay(10);
+    Serial.println(F("What... I'm not asleep?!?"));  // it will never get here
+  }
+
+  // 9th test - Deep Sleep Instant for 10 seconds, wake with RF_DISABLED
+  if (resetLoop == 3) {  // fourth reset loop since power on
+    resetLoop = 4;  // advance to the next Deep Sleep test after the reset
+    updateRTC();  // save the current test state in RTC memory
+    Serial.println(F("\n9th test - in NO_RFCAL, Deep Sleep Instant for 10 seconds, wake with RF_DISABLED"));
+    float volts = ESP.getVcc();
+    Serial.printf("The internal VCC reads %1.3f volts\n", volts / 1000 );
+    Serial.println(F("press the button to continue"));
+    waitPushbutton(false, blinkDelay);
+    Serial.println(F("going into Deep Sleep now..."));
+    delay(10);  // sometimes the \n isn't printed without a short delay
+    ESP.deepSleepInstant(10E6, WAKE_RF_DISABLED); // good night!  D0 fires a reset in 10 seconds...
+    delay(10);
+    Serial.println(F("What... I'm not asleep?!?"));  // it will never get here
+  }
+
+  if (resetLoop == 4) {
+    resetLoop = 5;  // start all over
+    updateRTC();  // save the current test state in RTC memory
+    float volts = ESP.getVcc();
+    Serial.printf("The internal VCC reads %1.3f volts\n", volts / 1000 );
+    Serial.println(F("\nTests completed, in RF_DISABLED, press the button to do an ESP.restart()"));
+    waitPushbutton(false, 1000);
+    ESP.restart();
+  }
+}
+
+void waitPushbutton(bool usesDelay, unsigned int delayTime) {  // loop until they press the button
+  // note: 2 different modes, as both of the AUTOMATIC power saving modes need a long delay()
+  if (!usesDelay) {  // quick interception of button press, no delay()
+    blinkLED.reset(delayTime);
+    while (digitalRead(WAKE_UP_PIN)) {  // wait for a button press
+      if (blinkLED) {
+        digitalWrite(LED, !digitalRead(LED));  // toggle the activity LED
+        if (WiFi.localIP())  // don't check OTA if WiFi isn't connected
+          ArduinoOTA.handle();  //see if we need to reflash
+      }
+      yield();
+    }
+  } else {  // long delay() for the 2 AUTOMATIC modes, but it misses quick button presses
+    while (digitalRead(WAKE_UP_PIN)) {  // wait for a button press
+      digitalWrite(LED, !digitalRead(LED));  // toggle the activity LED
+      if (WiFi.localIP())  // don't check OTA if WiFi isn't connected
+        ArduinoOTA.handle();  //see if we need to reflash
+      delay(delayTime);
+    }
+  }
+  delay(50);  // debounce time for the switch, button pressed
+  while (!digitalRead(WAKE_UP_PIN))  // now wait for them to release the button
+    delay(10);
+  delay(50);  // debounce time for the switch, button released
+}
+
+uint32_t calculateCRC32(const uint8_t *data, size_t length) {
+  uint32_t crc = 0xffffffff;
+  while (length--) {
+    uint8_t c = *data++;
+    for (uint32_t i = 0x80; i > 0; i >>= 1) {
+      bool bit = crc & 0x80000000;
+      if (c & i) {
+        bit = !bit;
+      }
+      crc <<= 1;
+      if (bit) {
+        crc ^= 0x04c11db7;
+      }
+    }
+  }
+  return crc;
+}
+
+void updateRTC() {
+  rtcData.data[3] = resetLoop;  // save the loop count for the next reset
+  // Update CRC32 of data
+  rtcData.crc32 = calculateCRC32((uint8_t*) &rtcData.data[0], sizeof(rtcData.data));
+  if (resetLoop == 5)  // wipe the CRC in RTC memory when we're done with all tests
+    rtcData.crc32 = 0;
+  // Write struct to RTC memory
+  ESP.rtcUserMemoryWrite(64, (uint32_t*) &rtcData, sizeof(rtcData));
+}
+
+void init_WiFi() {
+  /* Explicitly set the ESP8266 as a WiFi-client (STAtion mode), otherwise by default it
+    would try to act as both a client and an access-point and could cause network issues
+    with other WiFi devices on your network. */
+  digitalWrite(LED, LOW);  // give a visual indication that we're alive but busy
+  WiFi.persistent(false);  // don't store the connection each time to save wear on the flash
+  WiFi.mode(WIFI_STA);
+  WiFi.config(staticIP, gateway, subnet);  // if using static IP, enter parameters at the top
+  WiFi.begin(AP_SSID, AP_PASS);
+  Serial.print(F("connecting to WiFi "));
+  Serial.println(AP_SSID);
+  DEBUG_PRINT(F("my MAC: "));
+  DEBUG_PRINTLN(WiFi.macAddress());
+  while (WiFi.status() != WL_CONNECTED)
+    delay(50);
+  DEBUG_PRINTLN(F("WiFi connected"));
+  while (!WiFi.localIP())
+    delay(50);
+  WiFi.setAutoReconnect(true);
+  DEBUG_PRINT(F("WiFi Gateway IP: "));
+  DEBUG_PRINTLN(WiFi.gatewayIP());
+  DEBUG_PRINT(F("my IP address: "));
+  DEBUG_PRINTLN(WiFi.localIP());
+}
+
+void init_OTA() {
+  // Port defaults to 8266
+  // ArduinoOTA.setPort(8266);
+
+  // Hostname defaults to esp8266-[ChipID]
+  // ArduinoOTA.setHostname("myesp8266"));
+
+  // No authentication by default
+  // ArduinoOTA.setPassword((const char *)"123"));
+
+  ArduinoOTA.onStart([]() {
+    Serial.println(F("Start"));
+  });
+  ArduinoOTA.onEnd([]() {
+    Serial.println(F("\nEnd"));
+  });
+  ArduinoOTA.onProgress([](unsigned int progress, unsigned int total) {
+    Serial.printf("Progress: %u%%\r", (progress / (total / 100)));
+  });
+  ArduinoOTA.onError([](ota_error_t error) {
+    Serial.printf("Error[%u]: ", error);
+    if (error == OTA_AUTH_ERROR) Serial.println(F("Auth Failed"));
+    else if (error == OTA_BEGIN_ERROR) Serial.println(F("Begin Failed"));
+    else if (error == OTA_CONNECT_ERROR) Serial.println(F("Connect Failed"));
+    else if (error == OTA_RECEIVE_ERROR) Serial.println(F("Receive Failed"));
+    else if (error == OTA_END_ERROR) Serial.println(F("End Failed"));
+  });
+  ArduinoOTA.begin();
+  yield();
+}