Open AccessArticle

Effect of Distributed Mass on the Node, Frequency, and Sensitivity of Resonant-Mode Based Cantilevers

Kewei Zhang

^*,

Qianke Zhu

and

Zhe Chen

School of Materials Science and Engineering, Taiyuan University of Science and Technology, Taiyuan 030024, China

Author to whom correspondence should be addressed.

Sensors 2017, 17(7), 1621; https://doi.org/10.3390/s17071621

Submission received: 8 June 2017 / Revised: 1 July 2017 / Accepted: 5 July 2017 / Published: 13 July 2017

(This article belongs to the Special Issue Surface Acoustic Wave and Bulk Acoustic Wave Sensors)

Download

Browse Figures

Figure 1
Schematic illustration of a resonant-mode based cantilever with a layer of distributed mass load on its surface. l and w are the length and width of the cantilever beam; tp and ta are the thickness of the passive layer and active layer; a is length of the mass layer; x-axis is established on the neutral axis; c is the distance between x-axis and the interface of the two layers. "> Figure 2
The mode of vibration of the cantilever with different mass load distribution (a/l) under: (a) First-order resonance mode; (b) Secnd-order resonance mode; (c) Third-order resonance mode; (d) Fourth-order resonance mode where ρmAm/ρ0A0 = 1. "> Figure 3
Behavior of nodal shift Δx of the cantilever with different mass load distribution (a/l) under: (a) Second-order resonance; (b) Third-order resonance; (c) Fourth-order resonance where ρmAm/ρ0A0 = 1. "> Figure 4
The behavior of frequency shift of the cantilever with different mass distribution where ρmAm/ρ0A0 = 1. "> Figure 5
The behavior of sensitivity of the cantilever as the change of mass distribution under different resonance modes where ρmAm/ρ0A0 = 1. "> Figure 6
The maximal sensitivity as a function of mass load distribution (a/l). "> Figure 7
Sensitivity of the cantilever as a function of load mass under (a1) first-order resonance, (b1) second-order resonance, (c1) third-order resonance, and (d1) fourth-order resonance. All the data points are fitted by linear functions and the slopes of the linear fittings as a function of a/l are shown in <a href="#sensors-17-01621-f007" class="html-fig">Figure 7</a>(a2,b2,c2,d2). "> Figure 7 Cont.
Sensitivity of the cantilever as a function of load mass under (a1) first-order resonance, (b1) second-order resonance, (c1) third-order resonance, and (d1) fourth-order resonance. All the data points are fitted by linear functions and the slopes of the linear fittings as a function of a/l are shown in <a href="#sensors-17-01621-f007" class="html-fig">Figure 7</a>(a2,b2,c2,d2). ">

Versions Notes

Abstract

We derived an analytical expression for a resonant-mode based bi-layered cantilever with distributed mass load. The behavior of mode of vibration, nodal position, frequency shift, as well as sensitivity under different mass load distributions was theoretically studied. The theoretical results suggested that asymmetric mass load distribution leads to the shift of nodes as well as the sensitive regions of a resonant-mode based cantilever. n − 1 local maximal sensitivities and n − 1 local minimal sensitivities are observed when the cantilever vibrates in the nth-order resonance. The maximal sensitivity is found at the first local maximal sensitivity and the behavior of mass load length as a function of the maximal sensitivity follows the rule of an exponent decaying function. The sensitivity increases as the load mass increases for the same mass load distribution, but the corresponding slopes are different.

Keywords:

cantilever; mass load; node; frequency shift; sensitivity

1. Introduction

In the past decades, resonant-mode based cantilevers have shown high potential for the bio/chemical sensing applications [1,2,3,4]. The working principle is based on the shift in the resonant frequency due to the mass load caused by the specific binding of targets (i.e., microorganism, chemicals) on their surfaces [5,6,7]. For any type of sensors, sensitivity is an important parameter to characterize their performance. The sensitivity (S_m) for a resonant-mode based cantilever sensor is defined as its change in resonant frequency due to each unit of mass load, that is, S_m = −Δf/Δm [8]. A resonant-mode based cantilever can be single-layered or multi-layered in structure depending on the beam materials and actuation mechanism [8]. Mathematically, a multi-layered cantilever can be treated as a single-layered cantilever with equivalent mechanical properties. The equations for the sensitivity of a single-layered cantilever in a flexural vibration mode in the following two cases have been known as

Case I: Targets are uniformly bound on the entire surface of a cantilever [9].

S_{m, u n i} = \frac{1}{4} \frac{λ_{n}^{2}}{π \sqrt{12}} \frac{h}{W L^{2}} \sqrt{\frac{E}{ρ^{3} (1 - σ^{2})}}

(1)

Case II: Targets are bound at the free end of a cantilever [10].

S_{m, t i p} = \frac{1}{0.944} \frac{λ_{n}^{2}}{π \sqrt{12}} \frac{1}{W L^{2}} \sqrt{\frac{E}{ρ^{3} (1 - σ^{2})}}

(2)

where λ_n is the dimensionless nth-mode Eigenvalue; h, W, L are the thickness, width, and length of the cantilever; E, ρ, and σ are the effective Young’s modulus, density, and the Poisson’s ratio of the beam material; Δm and M are the mass of the load and the cantilever itself (Δm<<M).

It is found that sensitivity is inversely proportional to the cantilever size. However, the signal would be too weak to be detected when the size is very small due to the limitation of measurement devices. From the viewpoint of material properties, a resonant-mode based cantilever with higher Young’s modulus and lower density can also increase the sensitivity. However, other material properties such as coupling coefficient and Q value also need to be considered, which would make the selection of the cantilever material difficult. Another way to increase the sensitivity is to use higher-order resonance modes [11,12,13,14]. However, there is also a concern about the signal strength. For the same cantilever, the sensitivity in case II is much higher than that in case I which means that target distribution has a strong effect on the sensitivity of a resonant-mode based cantilever. Therefore, besides decreasing the size and replacing materials, controlling the target (i.e., mass load) distribution is a practical way to increase the sensitivity of a resonant-mode based cantilever.

Some work has been done on studying the effect of mass load conditions on resonant frequency and sensitivity of resonant-mode based cantilevers. Yi et al. investigated, both experimentally and theoretically, the resonance frequency of a piezoelectric single-layered cantilever with point mass loaded at the tip of the cantilever [15]. Dohn et al., derived an analytical expression for the resonant frequency of a cantilever with point mass load in different positions [16]. Maraldo et al., experimentally investigated the variation of sensitivity of a piezoelectric bi-layered cantilever with the change of point mass position and magnitude [17]. In the previous study, we established a theoretical equation for a bi-layered cantilever attached with point mass and investigated the effect of loading position and mass magnitude on the sensitivity of the cantilever using a modal analysis method [18]. In this work, a further theoretical investigation on the mode of vibration, node, resonant frequency, and sensitivity of a bi-layered resonant-mode based cantilever with distributed mass load was done aiming at development of a highly sensitive cantilever by controlling the target distribution.

2. Theory and Derivation

A bi-layered cantilever is composed of an active layer made of smart materials (i.e., magnetostrictive materials, piezoelectric materials) and a passive layer made of structural materials. Due to magnetostriction or piezoelectric effect of the active layer and restriction of the structure layer, the cantilever vibrates in a flexural mode when subjected to an alternative magnetic or electric field along the beam length direction. A bi-layered cantilever with a layer of distributed mass load is shown in Figure 1.

The kinetic energy (T) and potential energy (V) of the bi-layered cantilever as shown in Figure 1 are expressed as

T = \frac{1}{2} \int_{0}^{l} ρ_{0} A_{0} {(\frac{\partial u (x, t)}{\partial t})}^{2} d x + \frac{1}{2} \int_{0}^{a} ρ_{m} A_{m} {(\frac{\partial u (x, t)}{\partial t})}^{2} d x

(3)

V = \frac{1}{2} \int_{0}^{l} E_{0} I_{0} (\frac{\partial^{2} u (x, t)}{\partial x^{2}}) d x

(4)

where A₀ = A_a + A_p;

ρ_{0} = \frac{ρ_{a} A_{a} + ρ_{p} A_{p}}{A_{a} + A_{p}}

;

E_{0} I_{0} = \frac{E_{a}}{1 - ν_{a}^{2}} I_{a} + \frac{E_{p}}{1 - ν_{p}^{2}} I_{p}

; A_a, ρ_a, E_a, v_a, and I_a are the cross-sectional area, density, Young’s modulus, Poisson’s ratio, and moment of inertia of the active layer; A_p, ρ_p, E_p, v_p, and I_p are the cross-sectional area, density, Young’s modulus, Poisson’s ratio, and moment of inertia of the passive layer;

u (x, t) = \sum_{i = 1}^{n} φ_{i} (x) q_{i} (t)

where φ_i(x) is the mode shape function and q_i(t) is the generalized coordinate.

Equations (3) and (4) can be further simplified as

T = \frac{1}{2} {\dot{q}}^{T} (M_{0} + M_{1}) \dot{q}

(5)

V = \frac{1}{2} q^{T} K q

(6)

where

M_{0} = \int_{0}^{l} ρ_{0} A_{0} φ_{i}^{} (x) φ_{j}^{} (x) d x

; M₁ = ρ_mA_mφ_i(x)φ_j(x)dx; M = M₀ + M₁;

K = \int_{0}^{l} E_{0} I_{0} (\frac{\partial^{2} φ_{i}}{\partial x^{2}}) (\frac{\partial^{2} φ_{j}}{\partial x^{2}}) d x

It is known that the mode shape function

φ_{n} = \sin β_{n} x - \sinh β_{n} x - α_{n} (\cos β_{n} x - \cosh β_{n} x)

[9] (where

α_{n} = \frac{\sin β_{n} l + \sinh β_{n} l}{\cosh β_{n} x + \cos β_{n} x}

; n = 1, 2, 3,… and the values of β_n for the first four order modes are β₁ = 1.87510/l, β₂ = 4.69410/l, β₃ = 7.85476/l, β₄ = 10.99554/l, respectively) satisfies the boundary conditions of a single-layered cantilever

Combining Equations (4) and (5) and Lagrange’s Equation, the governing vibration equation of the cantilever with distributed mass load is given by

(K - ω_{n}^{2} M) q = 0

(7)

Obviously, the resonant frequency and mode of vibration of a cantilever is dependent on K and M which are affected by mass load distribution. By solving Equation (7), q and ω_n are determined and the resonant frequency f_n is calculated by

f_n = ω_n/2π

(8)

Finally, sensitivity S_m_,n is obtained by

S_{m, n} = \frac{f_{n, 0} - f_{n, m}}{Δ m}

(9)

where Δm is the load mass; f_n_,0 and f_n_,m are the nth-order resonant frequency of the cantilever without and with mass load.

3. Materials and Mass Load Conditions

In this study, the commercially available magnetostrictive alloy Metglas^TM 2826 (Metglas Inc., Conway, SC, USA) is selected as the active layer and copper is selected as the passive layer. The material properties and mass load conditions are listed in Table 1.

4. Results and Discussion

4.1. Effecton Modes of Vibration and Nodal Positions

Figure 2 shows the behavior of mode of vibration of the cantilever with different mass load distribution (a/l). Disregarding the fixed end, n − 1 nodes are observed for the nth-order resonance mode. Moreover, the change in mode of vibration with mass load distribution causes the nodes to shift (i.e., the difference between the nodal position x of the cantilever with mass load a/l ≠ 0 and without mass load a/l = 0) to the fixed end of the cantilever beam.

To further investigate the behavior of nodal position under different mass load distributions, the nodal shift Δx as a function of a/l is plotted as shown in Figure 3. Clearly, for all the nodes, the nodal shift firstly increases to the maximum and then decreases to zero as a/l increases to 1. Since a/l = 1 means that the mass is uniformly and symmetrically distributed on the entire surface of the cantilever, we can conclude that asymmetric mass load distributions (i.e., a/l ≠ 1) cause the nodes to shift. However, the value of nodal shift is not related to the degree of symmetry of mass distribution. For example, for the second-order resonance, the sequence of a/l causing the nodes shift from the largest to the smallest is a/l = 0.7, 0.8, 0.6, 0.9, 0.5, 0.4, 0.3, 0.2, 0.1. Moreover, the value of a/l corresponding to the maximal nodal shift is found near the nodal position and decreases with the resonance order increasing for the same node. For example, the value of a/l corresponding to the maximal shift for node 1 in the second-order, third-order, and fourth-order resonances are ~0.75, ~0.45, and ~0.3, respectively.

4.2. Effecton Resonant Frequency

Figure 4 shows frequency shift of the cantilever as a function of mass load distribution under different order resonances. It can be seen that the frequency shift increases as a/l increases for each resonance mode. However, the curves are nearly flat when the values of a/l fall in some specific ranges as marked by the colored arrows. In the other words, mass loaded in these regions has little contribution on frequency shift. It is worth noting that the nodal number is the same as that of the flat regions and each nodal positionnearly corresponds to the middle of a flat region. This phenomenon is very similar with the experimental results for the cantilevers reported by Johnson, B.N. et al. [22] and that of free-standing mangetostricitive sensors in longitudinal vibration mode [23]. Particularly, when the mass is loaded at a node, there would be no effect on resonant frequency shift. Therefore, it is believed that the closer the mass is loaded to the node of the cantilever, the less is contributed to the frequency shift and vice versa. Since the nodal positions shift as mass load distribution changes, the mass sensitive regions shift as the nodes move.

4.3. Effecton Sensitivity

Figure 5 shows sensitivity (S_m) of the cantilever as a function of mass distribution under different resonance modes. For the first order resonance, the sensitivity increases slowly at beginning and then increases dramatically as a/l increases. For the higher order resonance modes, the sensitivity first increases to the maximum and then fluctuates with decaying amplitude as a/l increases which results in n − 1 peaks (local maximum) and n − 1 valleys (local minimum) for the cantilever vibrating in the nth-order resonance and these values are found to be the points of inflection of the curves in Figure 4. Below the value of a/l for the maximal sensitivity, the higher the resonance order, the faster the sensitivity increases as a/l. It is also found that the value of a/l for each local minimum is close to, but slightly larger than, the corresponding nodal position. Taking the fourth-order resonance as an example, the values of a/l for the three minimal sensitivities are ~0.4, ~0.7, and ~0.95 while the three nodal positions are ~0.36, ~0.64, and ~0.91, respectively.

Moreover, a/l for the maximal sensitivity shifts to the fixed end as the resonance order increases as shown in Figure 6. It is found that the data curve can be fitted well by an exponent decaying function as follows

S_m,max = y₀ + Ae^(−x/c)

(10)

where y₀ = 0.05842, A = 21.72383, c = 1.62126 × 10⁻⁴; x represents a/l.

Therefore, a/l corresponding to the maximal sensitivity of the cantilever under higher order resonances can be predicted, based on Equation (10).

The behavior of sensitivity of the cantilever with mass load in six different density ratios (i.e., ρ_mA_m/ρ₀A₀ = 0.5, 0.6, 0.7, 0.8, 0.9, 1) for the first four order resonances are shown in Figure 7(a1,d1). It can be seen that the sensitivity is linearly proportional to load mass for the same mass distribution a/l under the same order resonance but the slopes are different as the value of a/l changes as shown in Figure 7(a2,d2). It is worth noting that the behavior of the slopes as a function of a/l is very similar with that of the sensitivity in the same order resonance as shown in Figure 5 but the corresponding peaks and valleys are not in the same positions except for the first order resonance. In other words, the maximal sensitivity does not increase the fastest as the mass load increases for high order resonances. On the other hand, the sensitivity increases the slowest as the mass load increases when a/l closes to zero.

5. Conclusions

The analytical expression for a resonant-mode based bi-layered cantilever with distributed load mass is derived and the mode of vibration, nodal point, resonant frequency, as well as sensitivity can be determined with given mass distribution conditions. Based on the theoretical results, several conclusions are made as follows:

Asymmetric mass load distribution causes the nodal points as well as the sensitive regions to shift but the shift value is not related to the degree of symmetry of mass load distribution.
There are n − 1 local maximal and n − 1 local minimal values for the sensitivity changing as mass load length when the cantilever vibrates in the nth-order resonance and the maximal sensitivity is found at the first local maximal value.
The behavior of mass load length as a function of the maximal sensitivity follows the rule of an exponent decaying function.
Sensitivity linearly increases as the load mass increases for the same mass load distribution and behavior of the slopes as a function of mass load length is very similar to that of the sensitivity in the same order resonance but the peak and valley positions are different.

Acknowledgments

This work was supported by the program for the Top Young Academic Leaders of Higher Learning Institutions of Shanxi (2014), Shanxi Province Science Foundation for Youths (2015021069), “131” Leading Talents Project of Higher Education Institutions in Shanxi (2015), Overseas Students Science and Technology Activities Project Merit Funding (2016) and the Fund for Shanxi Key Subjects Construction.

Author Contributions

Kewei Zhang conceived and designed this research and wrote the paper. Kewei Zhang made the derivation and calculation; Qianke Zhu and Zhe Chen performed the simulation and fitting.

Conflicts of Interest

The authors declare no conflict of interest.

References

Johnson, B.N.; Mutharasan, R. Biosensing using dynamic-mode cantilever sensors: A review. Biosens. Bioelectron. 2012, 32, 1–18. [Google Scholar] [CrossRef] [PubMed]
Zhang, K.W.; Zhang, L.; Fu, L.L.; Li, S.Q.; Chen, H.Q.; Cheng, Z.Y. Magnetostrictive resonators as sensors and actuators. Sens. Actuators A Phys. 2013, 200, 2–10. [Google Scholar] [CrossRef]
Sharma, H.; Mutharasan, R. Rapid and sensitive immuno detection of Listeria monocytogenes in milk using a novel piezoelectric cantilever sensor. Biosens. Bioelectron. 2013, 45, 158–162. [Google Scholar] [CrossRef] [PubMed]
Rosario, R.; Mutharasan, R. Piezoelectric excited millimeter sized cantilever sensors formeasuring gas density changes. Sens. Actuators B Chem. 2014, 192, 99–104. [Google Scholar] [CrossRef]
Johnson, B.N.; Mutharasan, R. A cantilever biosensor-based assay for toxin-producing cyanobacteria Microcystis aeruginosa using 16S rRNA. Environ. Sci. Technol. 2013, 42, 12333–12341. [Google Scholar] [CrossRef] [PubMed]
Zhang, K.W.; Fu, L.L.; Zhang, L.; Cheng, Z.Y.; Huang, T.S. Magnetostrictive particle based biosensors for in situ and real-time detection of pathogens in water. Biotechnol. Bioeng. 2014, 111, 2229–2238. [Google Scholar] [CrossRef] [PubMed]
Fu, L.L.; Zhang, K.W.; Li, S.Q.; Wang, Y.H.; Huang, T.S.; Zhang, A.X.; Cheng, Z.Y. In situ real-time detection of E. coli in water using antibody-coatedmagnetostrictive microcantilever. Sens. Actuators B Chem. 2010, 150, 220–225. [Google Scholar] [CrossRef]
Fu, L.L.; Li, S.Q.; Zhang, K.W.; Chen, I.H.; Petrenko, V.A.; Cheng, Z.Y. Magnetostrictive microcantilever as an advanced transducer for biosensor. Sensors 2007, 7, 2929–2941. [Google Scholar]
Merhaut, J. Theory of Electroacoustics; McGraw-Hill Inc.: New York, NY, USA, 1981. [Google Scholar]
Lacheisserie, E. Magnetostriction: Theory and Applications of Magnetoelasticity; CRC Press Inc.: New York, NY, USA, 1993. [Google Scholar]
Lochon, F.; Dufour, I.; Rebière, D. An alternative solution to improve sensitivity of resonant microcantilever chemical sensors: comparison between using high-order modes and reducing dimensions. Sens. Actuators B Chem. 2005, 108, 979–985. [Google Scholar] [CrossRef]
Jin, D.Z.; Li, X.X.; Liu, J.; Zuo, G.M.; Wang, Y.L.; Liu, M.; Yu, H.T. High-mode resonant piezoresistive cantilever sensors for tens-femtogram resoluble mass sensing in air. J. Micromech. Microeng. 2011, 16, 1017–1023. [Google Scholar] [CrossRef]
Johnson, B.N.; Mutharasan, R. Sample preparation-free real-time detection of microRNA in human serum using piezoelectric biosensors at attomole level. Anal. Chem. 2012, 84, 10426–10436. [Google Scholar] [CrossRef]
Neves, M.A.D.; Blaszykowski, C.; Bokhari, S.; Thompson, M. Ultra-high frequency piezoelectric aptasensor for the label-free detection of cocaine. Biosens. Bioelectron. 2015, 72, 383–392. [Google Scholar] [CrossRef] [PubMed]
Yi, J.W.; Shih, W.Y.; Shih, W.H. Effect of length, width, and mode on the mass detection sensitivity of piezoelectric unimorph cantilevers. J. Appl. Phys. 2002, 91, 1680–1686. [Google Scholar] [CrossRef]
Dohn, S.; Svendsen, W.; Boisen, A.; Hansen, O. Mass and position determination of attached particles on cantilever based mass sensors. Rev. Sci. Instrum. 2007, 78. [Google Scholar] [CrossRef] [PubMed]
Maraldo, D.; Mutharasan, R. Mass-change sensitivity of piezoelectric-excited millimeter-sized cantilever (PEMC) sensors: Model and experiments. Sens. Actuators B Chem. 2008, 132, 140–148. [Google Scholar] [CrossRef]
Zhang, K.W.; Chai, Y.S.; Fu, J.H. Study of node and mass sensitivity of resonant mode based cantilevers with concentrated mass loading. AIP Adv. 2015, 5. [Google Scholar] [CrossRef]
Read, D.T. Young’s modulus of thin films by speckle interferometry. Meas. Sci. Technol. 1998, 9, 676–685. [Google Scholar] [CrossRef]
The Properties of Metglas 2826. Available online: http://www.metglas.com (accessed on 7 July 2017).
Liang, C.; Morshed, S.; Prorok, B.C. Correction for longitudinal mode vibration in thin slender beams. Appl. Phys. Lett. 2007, 90. [Google Scholar] [CrossRef]
Johnson, B.N.; Mutharasan, R. A novel experimental technique for determining node location in resonant mode cantilevers. J. Micromech. Microeng. 2011, 21. [Google Scholar] [CrossRef]
Zhang, K.W.; Zhang, L.; Chai, Y.S. Mass Load Distribution Dependence of Mass Sensitivity of Magnetoelastic Sensors under Different Resonance Modes. Sensors 2015, 15, 20267–20278. [Google Scholar] [CrossRef] [PubMed]

Figure 1. Schematic illustration of a resonant-mode based cantilever with a layer of distributed mass load on its surface. l and w are the length and width of the cantilever beam; t_p and t_a are the thickness of the passive layer and active layer; a is length of the mass layer; x-axis is established on the neutral axis; c is the distance between x-axis and the interface of the two layers.

Figure 2. The mode of vibration of the cantilever with different mass load distribution (a/l) under: (a) First-order resonance mode; (b) Secnd-order resonance mode; (c) Third-order resonance mode; (d) Fourth-order resonance mode where ρ_mA_m/ρ₀A₀ = 1.

Figure 3. Behavior of nodal shift Δx of the cantilever with different mass load distribution (a/l) under: (a) Second-order resonance; (b) Third-order resonance; (c) Fourth-order resonance where ρ_mA_m/ρ₀A₀ = 1.

Figure 4. The behavior of frequency shift of the cantilever with different mass distribution where ρ_mA_m/ρ₀A₀ = 1.

Figure 5. The behavior of sensitivity of the cantilever as the change of mass distribution under different resonance modes where ρ_mA_m/ρ₀A₀ = 1.

Figure 6. The maximal sensitivity as a function of mass load distribution (a/l).

Figure 7. Sensitivity of the cantilever as a function of load mass under (a1) first-order resonance, (b1) second-order resonance, (c1) third-order resonance, and (d1) fourth-order resonance. All the data points are fitted by linear functions and the slopes of the linear fittings as a function of a/l are shown in Figure 7(a2,b2,c2,d2).

Table 1. The cantilever beam material properties and mass load conditions in this study.

Properties	Beam Materials	Symbol	Unit	Value
Young’s modulus	Copper	E_p	GPa	110 [19]
Young’s modulus	Metglas 2826	E_a	GPa	105 [20]
Density	Copper	ρ_p	kg/m³	8.9 × 10³ [19]
Density	Metglas 2826	ρ_a	kg/m³	7.9 × 10³ [20]
Poisson’s ratio	Copper	v_p	/	0.36 [19]
Poisson’s ratio	Metglas 2826	v_a	/	0.33 [21]
Length	Copper	l	mm	1
Length	Metglas 2826	l	mm	1
Width	Copper	w	mm	0.2
Width	Metglas 2826	w	mm	0.2
Thickness	Copper	t_p	μm	15
Thickness	Metglas 2826	t_a	μm	15
Length ratio of mass load to the cantilever beam	Copper	a/l	/	0, 0.1, 0.2, …, 1.0
ρ_mA_m/ρ₀A₀	/	r	/	0.5, 0.6, 0.7, 0.8, 0.9, 1

© 2017 by the authors. Licensee MDPI, Basel, Switzerland. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC BY) license (http://creativecommons.org/licenses/by/4.0/).

Share and Cite

MDPI and ACS Style

Zhang, K.; Zhu, Q.; Chen, Z. Effect of Distributed Mass on the Node, Frequency, and Sensitivity of Resonant-Mode Based Cantilevers. Sensors 2017, 17, 1621. https://doi.org/10.3390/s17071621

AMA Style

Zhang K, Zhu Q, Chen Z. Effect of Distributed Mass on the Node, Frequency, and Sensitivity of Resonant-Mode Based Cantilevers. Sensors. 2017; 17(7):1621. https://doi.org/10.3390/s17071621

Chicago/Turabian Style

Zhang, Kewei, Qianke Zhu, and Zhe Chen. 2017. "Effect of Distributed Mass on the Node, Frequency, and Sensitivity of Resonant-Mode Based Cantilevers" Sensors 17, no. 7: 1621. https://doi.org/10.3390/s17071621

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Menu