Open AccessData Descriptor

Measurements of LoRaWAN Technology in Urban Scenarios: A Data Descriptor

Pavel Masek

^1,*

Martin Stusek

^1,2

Ekaterina Svertoka

^1,3

Jan Pospisil

Radim Burget

Elena Simona Lohan

Ion Marghescu

Jiri Hosek

and

Aleksandr Ometov

Department of Telecommunications, Brno University of Technology, 616 00 Brno, Czech Republic

Unit of Electrical Engineering, Tampere University, 33720 Tampere, Finland

Department of Telecommunications, University Politehnica of Bucharest, 061071 Bucharest, Romania

Author to whom correspondence should be addressed.

Data 2021, 6(6), 62; https://doi.org/10.3390/data6060062

Submission received: 31 March 2021 / Revised: 19 May 2021 / Accepted: 1 June 2021 / Published: 10 June 2021

(This article belongs to the Special Issue Measurements of User and Sensor Data from the Internet of Things (IoT) Devices)

Download

Browse Figures

Figure 1
The network architecture of the LoRaWAN network. "> Figure 2
Summary diagram of ED’s behavior for LoRaWAN. "> Figure 3
Evaluation board constructed for testing LPWA technologies. "> Figure 4
Durability measurements of devices in different climatic conditions in the temperature chamber Vötsch VC3 7018. "> Figure 5
Current consumption during 50 B message transmission. "> Figure 6
Unconfirmed transmission power consumption. "> Figure 7
Confirmed transmission power consumption. "> Figure 8
Measurement locations in Brno, Czech Republic. "> Figure 9
Effect of the distance to the nearest GW on the outage probability. "> Figure 10
Observed relation of RSSI and distance per successfully delivered packet. "> Figure 11
Observed relation of SNR and distance per successfully delivered packet. "> Figure 12
Observed relation of SNR and RSSI per successfully delivered packet. "> Figure 13
BUT sensor RSSI samples relative frequency histogram. "> Figure 14
City center sensor RSSI samples relative frequency histogram. "> Figure 15
BUT sensor SNR samples relative frequency histogram. "> Figure 16
City center sensor SNR samples relative frequency histogram. ">

Versions Notes

Abstract

This work is a data descriptor paper for measurements related to various operational aspects of LoRaWAN communication technology collected in Brno, Czech Republic. This paper also provides data characterizing the long-term behavior of the LoRaWAN channel collected during the two-month measurement campaign. It covers two measurement locations, one at the university premises, and the second situated near the city center. The dataset’s primary goal is to provide the researchers lacking LoRaWAN devices with an opportunity to compare and analyze the information obtained from 303 different outdoor test locations transmitting to up to 20 gateways operating in the 868 MHz band in a varying metropolitan landscape. To collect the data, we developed a prototype equipped with a Microchip RN2483 Low-Power Wide-Area Network (LPWAN) LoRaWAN technology transceiver module for the field measurements. As an example of data utilization, we showed the Signal-to-noise Ratio (SNR) and Received Signal Strength Indicator (RSSI) in relation to the closest gateway distance.

Dataset: Available on GitHub: https://github.com/BUTResearch/MDPI_Data_Urban_LPWA_Measurement (accessed on 30 May 2021).

Dataset License: CC-BY 4.0

Keywords:

industrial IoT; LPWAN; LoRaWAN; urban measurements; dataset

1. Introduction

Today, the definition of a smart machine includes devices that can exchange data with other devices—i.e., Machine-to-Machine (M2M) approach or the cloud—execute a number of specific commands, and change the logic of work depending on external conditions, to cope with work that previously needed a person, i.e., Human-to-Machine (H2M) [1,2]. High functionality in a small size, which, in a few touches, satisfies a large number of human needs, from communication to health monitoring, makes smart devices a part of the Internet of Things (IoT, which also covers massive Machine-Type Communications (mMTC), one of the fastest-growing technologies of the last decade [3,4,5,6]. Experts agree that the smart device market will continue to grow in the near future due to their convenience, broad capabilities, and new “interesting features” [7]. Moreover, the number of connected smart devices has doubled over the past five years, from 13 to 26 billion devices worldwide, and is estimated to reach the

38.6

billion milestone by 2025 and 50 billion by 2030 [8]. The largest share of this portion of the IoT market belongs to smartphones (approximately 19% [8]), with the next most significant niche being wearable devices, and the market of wearable devices that is estimated to reach

62.82

billion dollars by 2025 [9].

Smart devices, including wearable ones, vary greatly in required bandwidth, latency, reliability, size, etc. [10]. For example, en-body electronics and simpler monitoring devices possess low bandwidth as they are usually in “sleep” mode and “wake up” periodically to conduct predefined tasks (measurements, data transmission), while bandwidth-hungry devices spend more energy and in a faster way [11]. Moreover, implantable patches should have a small form-factor so that the usual communication options are not applicable, and wireless connectivity requires the use of very high frequencies in the THz range. Such significant differences between wearable device classes make it impossible to have a list of common requirements, and, consequently, single silver bullet communication solutions do not exist.

Communication technologies for the IoT devices can be divided into three groups depending on the range: (i) short-range solutions that allow for connections at a distance below few tens of meters (e.g., Bluetooth Low Energy (BLE), ZigBee [12]); (ii) medium-range, which can enable communication up to a few hundred meters (e.g., Wi-Fi solutions, DASH7, Ingenu); (iii) wide-range solutions, reaching few tens of kms in communication range (e.g., LoRaWAN, Narrowband IoT (NB-IoT), and Sigfox) [13,14,15,16,17]. Despite many smart devices, most sensor-oriented ones are low-power (i.e., 10+ years of battery life) and have low data rates (usually, it refers to rates less than 1 Mbps). Such devices that are not aimed at high bandwidth can be equipped with Low-Power Wide-Area Network (LPWAN) solutions such as LoRaWAN, NB-IoT, or Sigfox for high energy efficiency and reliable operation in an urban scenario.

The question regarding which LPWAN technology will bring the most revenue in the next five years is still unsolved. To answer, it is necessary to consider many parameters such as functionality, availability, price, current demand, etc. On the one hand, the latest cellular technologies such as NB-IoT and LTE Cat-M seem to be more profitable due to their ease of use and superior performance. According to the Riot research [18], cellular LPWAN (i.e., NB-IoT and LTE Cat-M) will occupy the leading position among other LPWAN systems in the next three years. On the other hand, the growth of noncellular networks such as LoRaWAN and Sigfox should not be underestimated; Sigfox, for example, had second place after NB-IoT in 2018 [19]. Compared to cellular IoT solutions, noncellular LPWAN solutions have a lower data rate, lower power consumption, lower cost, and operate in unlicensed bands. However, some developers may consider their utilization for data collection from nonsmart wearables as well.

Among the LPWAN communication technologies, LoRaWAN is one of the most promising solutions for IoT [20], especially in the area of smart cities [21,22], smart farming [23,24], asset tracking [25], environmental monitoring [26], and smart waste management [25,27]. According to [25], the Compound Annual Growth Rate (CAGR) of the LoRaWAN market is going to achieve 47.2% between 2019 and 2027. The expected growth of the market could be explained by key features of the technology, which meet the requirements of rapidly increasing IoT systems, i.e., low power consumption and extended communication range. LoRaWAN solution offers low-cost deployment, different device classes for different conditions, direct connection to the cloud, positioning, and feasibility for both outdoor and indoor environments due to better penetration capabilities compared, for example, to Wi-Fi or BLE [28,29].

Currently, not many datasets are found regarding the application of the LoRaWAN [30,31,32,33]. Authors in [30] presented the dataset collected from the underground (up to 50 cm in depth) LoRaWAN network in Australia during 10 months using 5 transmitters, 2 receivers, and containing information related to farms such as soil moisture, temperature, etc. The dataset in [31] comprises the information (packet header and parameters reported by base stations) collected over 2–4 months by manually deploying 9 gateways (GW) (5 outdoor with Line-of-Sight (LOS), 3 indoor with limited LOS, and 1 indoor with Non-Line-of-Sight (NLOS)) in London. Authors identify that this work could be used for different purposes, such as investigating the changes in network parameters in the long term or testing the algorithms to validate their appropriateness for certain applications. A large fingerprinting dataset [32] was collected using postal cars in Antwerp over 3 months with 68 GWs scattered throughout the city. The dataset contains information reported by the GWs and the real positions where uplink packets were sent from.

LoRaWAN is an in-demand technology that has carved its niche among communication solutions for the IoT. It seems to be most applicable when we do not need high throughput but need the system’s low cost and high reliability, especially for resource-constrained devices. The technology is improving, and statistics are required to explore and expand its potential, though there are very few open-source datasets. Therefore, in this paper, we provide a LoRaWAN coverage dataset collected in Brno, Czech Republic. The motivation to prepare this dataset was pushed forward by encouraging researchers to work with LoRaWAN technology to identify its application prospects and benefits as a communication solution for smart devices.

The rest of the paper is organized as follows. First, Section 2 provides an overview of LoRaWAN technology. Section 3 covers the data description. Further, Section 4 describes the preparation phase of the measurements and outlines the measurement setup for both short- and long-term measurement campaigns. The next section visualizes the most important findings from both measurement campaigns. Finally, the last section provides the summary of the data descriptor.

2. LoRaWAN Technology Overview

The selected LoRaWAN technology is arguably one of the most well-known representative of LPWAN technologies operating in the Industrial, Scientific, and Medical (ISM) (unlicensed) frequency band. The LoRaWAN network infrastructure consists of end devices (ED), GWs, and a network server (NS). Besides these elements, the network may contain a specialized network join (NJ) server to handle roaming between networks. The bare minimum LoRaWAN network consists of a single GW and the NS (which may be integrated into the GW). These two elements are typically connected through an IP-based interface. The functionality of the NS and the user application programming interfaces (APIs) might differ depending on the operator. In most cases, the transmission is initiated by an ED by using an Aloha-like channel access mechanism [34]. Therefore, the ED can initiate communication at any time, without violating the selected radio channel’s operational restriction.

Significantly, LoRaWAN belongs to ISM band. The key parameters can be found in Table 1, making the operation free in contrast to, for example, cellular-based NB-IoT technology operating in the licensed LTE band. The utilization of unlicensed bands is regulated by the government (in the case of the Czech Republic, the Czech Telecommunication Office is the regulator) and therefore has some operational restrictions.

The LoRaWAN provides two options for infrastructure deployment. End-users can use the infrastructure provided by communication operators by paying for their services, see Figure 1 with the description of the blocks in Table 2. An alternative is the deployment of private LoRaWAN infrastructure.

The LoRaWAN network protocol does not have a strict specification for the used modulation technique, but an arbitrary method can be used. However, the most widely used is the Long-Range (LoRa) modulation patented by Semtech [35]. This modulation is based on a spread spectrum technique called Chirp Spread Spectrum (CSS). The spreading of the spectrum is achieved by generating a chirp signal that continuously varies in frequency. The data are then modulated on top of the chirp, spreading a narrowband signal over a wider bandwidth (of at least 125 kHz). The resulting signal has a spectral signature of noise, which makes it harder to detect or jam [36], and is resilient to a narrowband noise.

Furthermore, the chirp waveform frequency characteristics—i.e., the slope (directly affecting the symbol duration) of the LoRa modulation—can be modified by the spreading factor (SF) parameter ranging from 7 to 12. With slower frequency variation, each symbol is emitted with higher energy, thus enabling longer communication ranges at the cost of a lower data rate and longer on-air time. In general, the achievable bit rate varies from 250 (for SF12/125 kHz) to 21,900 bps (SF7/500 kHz), resulting in a maximum payload size from 11 (SF10—US region) up to 242 bytes (SF7—most of the regions). Due to the need for power efficiency, the EDs are commonly configured to use the lowest SF that allows reliable communication [37]. The LoRaWAN protocol also defines channel coding-forward error correction. The coding rate parameter value indicates the ratio between the original information’s bits and the redundant bits, which also adds another overhead.

The LoRaWAN ED may start its uplink transmission at any time, see Figure 2. An ED randomly selects one of up to 16 available frequency channels for its transmission (valid for the EU region). The SF and the transmit power used by the ED are either predefined or, specified (either by the ED itself or by the NS)—which is strongly recommended—based on the radio channel conditions between the ED and the nearest GW. The maximum payload for LoRaWAN uplink packets depends on the SF used and is at least 51 bytes (for the EU region). The number of messages per day is not limited either, but the ED is required to obey local restrictions concerning the maximum duty cycle. Packet retransmission in LoRaWAN is optional and rarely used.

The downlink functionality of the LoRaWAN ED depends on its class. Each LoRaWAN ED operating in class A opens two Receive Windows (RWs) following its uplink transmission. The first RW (RW1) follows after the preagreed waiting time (typically 1 s) and is opened in the same frequency channel that the ED used for its uplink transmission. The second RW (RW2) follows the first window after 1 s and is opened in the preagreed frequency channel (in the EU, typically in the

869.5

MHz channel). For SF used by the ED, RW1 depends on its SF for uplink, while RW2 is always opened with a predefined SF. An ED having only these RWs is classified as ED class A. The devices of class B are required to synchronize with the network and open periodic RWs at prespecified time slots. Finally, class C ED listens the entire time it is not transmitting or having RW1.

In addition to the duty cycle restrictions, there is also a limit on transmission power, especially for resource-constrained devices. The power values are defined here as Effective Radiated Power (ERP) values—the power that must be given to a reference half-wave dipole antenna to get the same electrical field strength as the actual device at the same distance in the direction of the antenna gain. Another often-used definition is Effective Isotropic Radiated Power (EIRP)—the power that must be given to a reference isotropic antenna to get the same electrical field strength as the actual device at the same distance. The EIRP and ERP can be converted into each other using

P_{E I R P} = P_{E R P} + 2.15

dB, if the powers are expressed in dBm [38]. Maximum transmission power limits are given by the LoRaWAN regional specification and by each country’s local regulations, which must be verified in advance. According to the LoRaWAN specification, EIRP limits generally range between 12.15–30 dBm [39].

2.1. LoRaWAN Regional Parameters for EU

There are two frequency plans available for the European continent: EU863–870 and EU433. Since the Czech CRA agency operates the ISM band 868 MHz network, only the first frequency plan will be discussed in more detail. Table 3 shows the relationship between the data rate (DR), which is a numeric value representing the spreading factor, bandwidth, and coding rate settings in the specified region, and the bit rate. For EU863–870, a coding rate of 4/5 is used by default. The table shows that the lower the data rate, the lower the bit rate (but this extends the communication coverage).

Six SF values using 125 kHz-bandwidth (namely, SF7 to SF12) are specified. For these, the on-air data throughput varies from 250 bps up to

5.47

kbps depending on the selected SF. Additionally, there is also one channel with a bandwidth of 250 kHz and SF7 with a throughput of 11 kbps [40,41]. Moreover, the channels with higher bandwidth or high-speed Frequency Shift Keying (FSK) modulation may be defined.

Each ED selects one of the sixteen available channels in frequency bands from 863 to 870 MHz. However, the condition is that each device (GWs and EDs) must also communicate on the default channels listed in Table 4. The ED must also comply with the duty cycle restriction and the maximum transmission power. The selected ISM frequency band of 868 MHz imposes the limitation of a 1% duty cycle with the maximum transmission power of 14 dBm (25 mW) [42].

3. Data Description

The provided open-access dataset consists of JavaScript Object Notation (JSON) records stored in Comma-Separated Values (CSV) files, and the data were gathered in a span of multiple hours during two days of measurements. Each JSON file contains parameters as described below. In addition to the payload itself, every record on the server also contains additional metadata. Metadata contains general information about the LoRaWAN message and the array of parameters that provide more detailed message reception information for each GW receiving the message separately. Notably, these names may differ between LoRaWAN service providers. In the case of Ceske Radiokomunikace (CRa), the metadata contains the following parameters [43]:

cmd—Command (message type): Incoming (uplink) message from the ED via the GW to the server. This also contains metadata from receiving GWs.
seqno—Sequence number: The sequence number of the message in the form of a 32-bit integer. The Network Server generates this number.
EUI—Extended Unique Identifier: A global identifier (64-bit) of the terminal device, which the manufacturer or owner assigns. The Institute of Electrical and Electronics Engineers (IEEE) Registration Authority manages the assignment of identifier pools. It is given in hexadecimal format. This identifier is used similarly to the MAC address of the network interface.
ts—Timestamp: The time of the received message recorded at the first receiving GW. The parameter indicates the number of milliseconds since the Unix epoch (1 January 1970).
fcnt—Frame count: Sequential number of the message (16-bit integer) sent from the device. In the case of a device reset, the value of the counter starts from zero. The value of this parameter can be used to detect a failure to receive messages.
port—The port number is used to distinguish the type of application payload message. It is, therefore, not necessary to explicitly add it to the application payload. The Port parameter’s (8-bit integer) possible values range from 1 to 223 for the users. Other values are reserved.
freq—Frequency: A value that corresponds to the frequency (expressed in Hertz) of the given LoRaWAN channel. Before transmitting each message, the ED pseudo-randomly selects from the range of available LoRaWAN channels on which it will transmit the message.
toa—Time on Air: Message transmission time in milliseconds. This value is directly proportional to the data rate and message size.
dr—Data Rate: The string parameter specifying the spreading factor, bandwidth, and coding rate. The spreading factor fundamentally affects the data rate and thus, the message time on-air. The value can be selected from the interval 7 to 12. Bandwidth values are only 125, 250, and 500 kHz. The larger the bandwidth, the higher the data rate.
ack—Acknowledge: The parameter is of a Boolean type and indicates whether the ED requires confirmation of the sent message. The default is to avoid using acknowledgments to reduce network traffic.
gws—Gateways: Contain an array of information objects from individual GWs, especially information about the parameters of the received signal, timestamp, identifier, and location of the GW.
- rssi—Received Signal Strength Indicator: The received signal level on the GW, expressed in dBm. The threshold value of the Semtech SX1301 receiver is −142 dBm [44].
- snr—Signal-to-Noise Ratio: This parameter gives the ratio between the received power signal and the noise floor power level in dB. If the SNR is greater than 0, the received signal level is higher than the noise level.
- ts—Timestamp: The time of the received message in milliseconds since the Unix era (1 January 1970).
- tmms—Time in ms: GPS time in milliseconds since 6 February 1980. The GW must have GPS connectivity.
- time—UTC of the received message, with microsecond precision in the ISO 8601 format.
- gweui—GW extended unique identifier: The 64-bit number in a hexadecimal format specific for each GW.
- lat—Latitude: GW GPS latitude parameter in decimal degrees. The GW must have GPS connectivity.
- lon—Longitude: GW GPS longitude parameter in decimal degrees. The GW must have GPS connectivity.
bat—Battery status of the ED 8-bit integer value (0—external power supply, 255—battery status is unknown, 1–254—correspond to battery status 0–100%).
data—The field contains HEX data, which is unique for the LoRaWAN device in question. It consists of information related to temperature, position, battery level, etc. In the case of our device, it represents our unique data format, which is specifically designed for the purposes of our measurements.
device_Lat—Latitude of the measurement point gathered from the GPS.
device_Lon—Longitude of the measurement point gathered from the GPS.

An example of one entry could be found in the following listing:

The undeniable advantage of the JSON format is that it is in a human-readable form. Thus, without the need for complex parsing, necessary information can be read immediately.

4. Measurement Details

To perform the measurement campaign, we designed and constructed the LPWA device prototype capable of transmitting data using diverse LPWA communication technologies. In the case of this paper, we take into account the LoRaWAN technology, i.e., the data transmissions utilizing the license-exempt frequency band. This section contains information related to the aforementioned construction of the device and discusses the executed measurement campaigns.

4.1. Evaluation Preparation

For the measurement campaign, a measurement prototype was developed and subsequently used for in-depth evaluation of energy consumption and communication capabilities of LoRaWAN—a prototype equipped with a Microchip RN2483 Low-Power Wide-Area LoRaWAN technology transceiver module; its main technical details are given in Table 5 while the actual module is depicted in Figure 3.

Before the measurements, the constructed prototype was tested in the temperature Vötsch VC3 7018 chamber as well as in the Electromagnetic Compatibility (EMC) anechoic chamber as they are both part of testing laboratories at Brno University of Technology, see Figure 4. Only the devices that passed these tests successfully, e.g., operating in the temperature range from

- 18

^{\circ}

C to

+ 85

^{\circ}

C, were included in testing.

In this work, we used the DC power analyzer Agilent N6705A [45] for current measurements as the power consumption was measured through dedicated test pins on a custom-designed board. While conducting the measurements, a significant growth of power consumption with increasing temperature was measured for the module in question, RN2483. The current consumption growth is caused by natural behavior of the semiconductor junction. Referring to the performed measurements, at the temperature

+ 85

^{\circ}

C, the current consumption in power-saving mode raised up to 20 A, which is more then 6 times higher consumption compared to

+ 25

^{\circ}

C. The power consumption characteristics of the LoRaWAN module depicted in Figure 5 clearly indicate that the device operates in Class A mode.

The short spike around 40 mA represents the message transmission of 50 B utilizing SF7. After the predefined 1 s delay, first, receive window RX1 is opened. Notably, when the confirmed message is sent, the duration of RX1 is longer than in the case of unconfirmed transmission. This extension is caused by the fact that actual data are transmitted during RX1 when an acknowledgment is sent. However, when the data is successfully received, no additional reception window (RX2) is opened. On the other hand, the unconfirmed mode still requires the opening of RX2 after the predefined delay of 2 s after data transmission. As a result, it may even lead to a decreased power consumption when the confirmed mode is used.

The actual measurements, depicted in Figure 6 and Figure 7, verify the theory mentioned above, as the confirmed transmission indicates slightly lower power consumption in all combinations of message sizes and spreading factors. From the message size of 100 B, the higher spreading factors are limited due to DC restriction; therefore, they are omitted in the results. The influence of the abovementioned effect is visible, especially for the small message sizes and low SF values.

Logically, the RX2 represents a more significant part of the current consumption when the transmission time is shorter. The new important finding is connected with the increasing SF value. Up to SF10, the power consumption rises nearly linearly. However, from SF11, the increase is more pronounced even though the transmission time doubles with each increase in SF. It is logical to assume that up to SF10, the reception windows represent a significant part of consumed energy.

4.2. City-Scale Measurement Campaign

The measurements campaign was executed in the urban area of Brno, Czech Republic. The test area covered around a 35-km radius with 231 test locations mainly located next to the public bus stops, see Figure 8 (The map of measurement points with the location data is accessible online via Google Maps). This area is covered with at least 20 CRA LoRaWAN network’s GWs, and the measurements were taken for all three default channels of 868 MHz band, with the 4/5 (default) coding rate, maximum SF 12, and maximum transmit power of 14 dBm to achieve maximum communication coverage.

The measurement class A devices were equipped with the vertically aligned dipole antennas and installed one meter above ground-level (the board was tilted 90

^{\circ}

to achieve the horizontal position), set up in test locations, and requested to transmit a set of five packets. All duplicates were kept during the transmissions (allowing us to analyze spatial diversity impact on an actual multi-GW LoRaWAN system). Next, the data was repetitively collected and automatically uploaded to centralized storage after the measurements.

4.3. Long-Term Measurement Campaign

With the ultimate goal of exploring long-term channel characteristics, we conducted a measurement campaign of LoRaWAN technology spanning over two months. One communication unit was placed on the rooftop of the BUT building approximately 25 m above ground-level for these measurements. This configuration represents a suburban scenario, as the university building is located in the Brno suburb. The second device was deployed on the windowsill of the authors’ flat situated near the city center. It is expected that the unit located in the city center will experience higher signal fluctuations due to the increased number of interference sources (surrounding buildings, passing cars, trams, etc.).

Both devices were set to transmit 12 B messages in unconfirmed mode every 90 min. The transmit power was set to 14 dBm with SF12 and a coding rate of 4/5 to provide maximum communication range. The reason for the selection of SF12 configuration is due to the measurement campaign goal being initially related to the scenario, where the success rate was the key performance indicator. During the two months, we gathered more than 1000 messages from each device.

5. Measurements Results

This section provides the most important results obtained after postprocessing of the collected data.

5.1. City-Scale Measurements Results

The presented data include the outage probability of the measurement-node from the closest LoRaWAN GW, see Figure 9. These values are derived via the Euclidean distance between each ED and GW. For better visualization, the distances are divided into 23 bins with 250-m steps. The results show that in the case of the LoRaWAN network’s real deployment in Brno, the maximum distance to the closest GW does not exceed 8 km. Notably, half of the nodes were within a 1 km radius from the GW and 80% in 2 km. Significantly, the threshold for successful packet delivery was also in a range of 1–2 km, since 50% of nodes in this distance experienced at least one packet loss.

The second part of measurement results corresponds to actual wireless channel characteristics, e.g., the distributions of RSSI and SNR for successfully delivered packets. We recall the map of measurement points with the location data that are accessible online via Google Maps. Figure 10 and Figure 11 indicate the impact of the communication range between the EDs and GWs on the key radio parameters, i.e., SNR and RSSI. Interestingly, Figure 10 and Figure 11 show that some packets were also delivered from distances over 50 km. Notably, the observed RSSI values range from −64 to −125 dBm (dynamic range of approximately 34 dB; the SNR is in the range from −20 to 14 dB), though SF12 is designed to typically work at −137 dBm. Nevertheless, during our campaign, we did not capture any data transmissions below –127 dBm. Additionally, referring to the SNR captured during the measurements, the SNR levels align with the theoretical assumptions as they do not cross the threshold of −20 dB.

The interrelation between the discussed parameters is given in Figure 12, where we can observe a significant deviation of both parameters. The dependency between the SNR and RSSI is linear and SNR is above 0 dB only in ideal radio conditions. For the rest (levels below −100 dBm), it is all over the place. Therefore, the results suggest that the SNR represents a more limiting factor that the RSSI as an even sample with low RSSI may have relatively good SNR.

5.2. Long-Term Measurement Results

The long-term RSSI measurement results depicted in Figure 13 and Figure 14 verify that our basic premise of BUT sensor experiencing smaller fluctuation and having an overall higher signal level was partially correct. Indeed, the BUT sensor’s signal levels are approximately 30-dB higher than in the case of the city center module. However, the RSSI fluctuation is less pronounced for the city center module. Most of the samples for both sensors fit in the 20-dB range around the average signal level; however, most of the values lie within the 10-dB area for the city center sensor. For the BUT sensor however, this range is almost 20 dB.

In the case of SNR, depicted in Figure 15 and Figure 16, the situation is slightly different. As expected, the BUT sensor indicates much better SNR values. Notably, almost 600 samples fit between 5 and 10 dB for the BUT sensor. Further, the SNR values of most of the samples are over 0 dB. Conversely, for the city center module, not a single sample has SNR better than 0 dB. On top of that, the SNR fluctuation of the city center module is significantly higher. The SNR values are more evenly distributed over the whole range of SNR values (around 10 dB). It is an exciting finding, as even in the case of the city center sensor, there are RSSI samples comparable to the BUT module. However, the SNR for these occasions is still significantly worse. Hence, it appears that SNR is more dependent on radio conditions and the overall separation distance between ED and GW than RSSI.

6. Data Descriptor Summary

This data descriptor paper provides the dataset descriptor of LoRaWAN technology measurements in the midsize city scenario of Brno, Czech Republic. The dataset covers 311 outdoor test locations in a varying landscape processed on 39 static gateway nodes. The dataset provides various measurement data ranging from communication to location-related information, providing the researchers with broad opportunities to analyze the deployment and improvement of the LoRaWAN operation for numerous IoT-use cases. In addition, we explore the long-term characteristics of the real-world LoRaWAN network based on a measurement campaign spanning over two months. Finally, we report on power consumption measurements conducted on an off-the-shelf LoRaWAN communication module using different SF settings and various message sizes. All mentioned datasets are publicly available at GitHub and will be extended after the collection of new, real-world measurement data.

Based on the conducted city-scale measurement campaign, it can be stated that LoRaWAN technology represents a solid communication technology for delay- and loss-tolerant application as it provides a cumulative packet delivery ratio of 83% during the whole experiment. Impressively, only 16 locations of 311 were not served, giving the overall outage probability of only 5.15%. Notably, the results suggest that the geographically closest GW does not always provide the best RSSI nor SNR. In reality, 40% of GWs with the best RSSI and 34% with the best SNR are not the closest ones.

The long-term measurements show exciting results. Even during the two months, the RSSI significantly fluctuated within the range of almost 50 dB. In terms of SNR, fluctuation ranged around 25 dB. These results suggest that the use of conventional empirical propagation models may lead to significant inaccuracies of the predicted path loss values. Hence, a more precise dynamic channels model will be needed. The provided data set may serve as a good starting point for the development of such a model.

Author Contributions

Conceptualization, P.M. and R.B.; methodology, P.M. and M.S.; software, M.S.; validation, J.P., E.S. and A.O.; formal analysis, A.O.; resources, E.S.L.; data curation, M.S. and E.S.; writing—original draft preparation, A.O.; writing—review and editing, E.S., J.P., P.M., E.S.L.; visualization, P.M.; supervision, A.O., J.H., I.M.; project administration, E.S.L.; funding acquisition, E.S.L. and A.O. All authors have read and agreed to the published version of the manuscript.

Funding

This work was supported by the European Union’s Horizon 2020 Research and Innovation programme under the Marie Skłodowska Curie grant agreement No. 813278 (A-WEAR: A network for dynamic WEarable Applications with pRivacy constraints).

Informed Consent Statement

Not applicable.

Data Availability Statement

Dataset is available on GitHub: https://github.com/BUTResearch/MDPI_Data_Urban_LPWA_Measurement (accessed on 30 May 2021).

Conflicts of Interest

The authors declare no conflict of interest. The funders had no role in the study’s design; in the collection, analyses, or interpretation of data; in the writing of the manuscript, or in the decision to publish the results.

Abbreviations

The following abbreviations are used in this manuscript:

ADR	Adaptive Data Rate
API	Application Programming Interface
AR	Augmented Reality
BLE	Bluetooth Low Energy
CRA	Czechia national LoRaWAN provider
CSS	Chirp Spread Spectrum
DL	Downlink
ED	End Device
EIRP	Effective Isotropic Radiated Power
EIRP	Effective Isotropic Radiated Power
ERP	Effective Radiated Power
FSK	Frequency-Shift Keying
GFSK	Gaussian Frequency-Shift Keying
GW	Gateway
H2M	Human-to-Machine
IEC	International Electrotechnical Commission
IEEE	Institute of Electrical and Electronics Engineers
IoT	Internet of Things
ISM	Industrial, scientific, and medical
LPWAN	Low-Power Wide-Area Network
LTE	Long-Term Evolution
M2M	Machine-to-Machine
MCL	Maximum Coupling Loss
mMTC	massive Machine-Type Communications
MR	Mixed Reality
NB-IoT	Narrowband Internet of Things
NFC	Near-Field-Communication
NS	Network Server
RF	Radio Frequency
RFID	Radio-Frequency Identification
RSSI	Received Signal Strength Indicator
RW	Receive Window
SF	Spreading Factor
SNR	Signal-to-Noise Ratio
UL	Uplink
VR	Virtual Reality
WiFi	Wireless Fidelity

References

Silverio-Fernández, M.; Renukappa, S.; Suresh, S. What is a Smart Device?—A Conceptualisation within the Paradigm of the Internet of Things. Vis. Eng. 2018, 6, 3. [Google Scholar] [CrossRef] [Green Version]
Stojkoska, B.L.R.; Trivodaliev, K.V. A Review of Internet of Things for Smart Home: Challenges and Solutions. J. Clean. Prod. 2017, 140, 1454–1464. [Google Scholar] [CrossRef]
McKinsey and Company. Growing Opportunities in the Internet of Things. Available online: https://www.mckinsey.com/industries/private-equity-and-principal-investors/our-insights/growing-opportunities-in-the-internet-of-things# (accessed on 30 May 2021).
Grand View Research. IoT Market Analysis By Component (Devices, Connectivity, IT Services, Platforms), By Application (Consumer Electronics, Retail, Manufacturing, Transportation, Healthcare) And Segment Forecasts To 2022. Available online: https://www.grandviewresearch.com/industry-analysis/iot-market (accessed on 30 May 2021).
Mozny, R.; Masek, P.; Stusek, M.; Mikulasek, M.; Ometov, A.; Hosek, J. Pitfalls of LPWA Power Consumption: Hands-On Design of Current Probe. In Proceedings of the 12th International Congress on Ultra Modern Telecommunications and Control Systems and Workshops (ICUMT), Online, 5–7 October 2020; pp. 13–19. [Google Scholar]
Ometov, A.; Daneshfar, N.; Hazmi, A.; Andreev, S.; Carpio, L.F.D.; Amin, P.; Torsner, J.; Koucheryavy, Y.; Valkama, M. System-Level Analysis of IEEE 802.11ah Technology for Unsaturated MTC Traffic. Int. J. Sens. Netw. 2018, 26, 269–282. [Google Scholar] [CrossRef]
Solentive. Smart Devices—The Fastest Technology Adoption In History. Radio Versions. 2020. Available online: https://www.solentive.com.au/smart-devices-the-fastest-technology-adoption-in-history/ (accessed on 30 May 2021).
HelpNetSecurity. Number of Connected Devices Reached 22 Billion, Where is the Revenue? 2019. Available online: https://www.helpnetsecurity.com/2019/05/23/connected-devices-growth/ (accessed on 30 May 2021).
Top 10 Companies in Wearable Devices Market. Meticulous Research. 2019. Available online: https://meticulousblog.org/top-10-companies-in-wearable-devices-market/ (accessed on 30 May 2021).
Ometov, A.; Shubina, V.; Klus, L.; Skibińska, J.; Saafi, S.; Pascacio, P.; Flueratoru, L.; Gaibor, D.Q.; Chukhno, N.; Chukhno, O.; et al. A Survey on Wearable Technology: History, State-of-the-Art and Current Challenges. Comput. Netw. 2021, 193, 108074. [Google Scholar] [CrossRef]
Ometov, A.; Kozyrev, D.; Rykov, V.; Andreev, S.; Gaidamaka, Y.; Koucheryavy, Y. Reliability-Centric Analysis of Offloaded Computation in Cooperative Wearable Applications. Wirel. Commun. Mob. Comput. 2017, 2017, 9625687. [Google Scholar] [CrossRef] [Green Version]
Svertoka, E.; Rusu-Casandra, A.; Marghescu, I. State-of-the-Art of Industrial Wearables: A Systematic Review. In Proceedings of the 13th International Conference on Communications (COMM), Bucharest, Romania, 18–20 June 2020; pp. 411–415. [Google Scholar]
Wen, S.; Heidari, H.; Vilouras, A.; Dahiya, R. A Wearable Fabric-based RFID Skin Temperature Monitoring Patch. IEEE Sens. 2016, 1–3. [Google Scholar] [CrossRef] [Green Version]
Ghamari, M.; Arora, H.; Sherratt, R.S.; Harwin, W. Comparison of Low-Power Wireless Communication Technologies for Wearable Health-Monitoring Applications. In Proceedings of the International Conference on Computer, Communications, and Control Technology (I4CT), Kuching, Malaysia, 21–23 April 2015; pp. 1–6. [Google Scholar] [CrossRef]
Alliance, W. The Benefit of Wi-Fi Connectivity in Wearable Devices. Available online: https://www.wi-fi.org/ko/beacon/jay-white/the-benefit-of-wi-fi-connectivity-in-wearable-devices (accessed on 30 May 2021).
Mozny, R.; Masek, P.; Stusek, M.; Zeman, K.; Ometov, A.; Hosek, J. On the Performance of Narrow-Band Internet of Things (NB-IoT) for Delay-Tolerant Services. In Proceedings of the 42nd International Conference on Telecommunications and Signal Processing (TSP), Budapest, Hungary, 1–3 July 2019; pp. 637–642. [Google Scholar]
Sun, H.; Zhang, Z.; Hu, R.Q.; Qian, Y. Wearable Communications in 5G: Challenges and Enabling Technologies. IEEE Veh. Technol. Mag. 2018, 13, 100–109. [Google Scholar] [CrossRef]
LPWAN Revenue Forecast, 2017 to 2023. 2017. Available online: https://shop.maravedis-bwa.com/products/lpwan-revenue-forecast-2017-to-2023 (accessed on 30 May 2021).
LoRa and Sigfox get Five-Year Boost with LTE-M and NB-IoT Failures. Enterprise IoT Insights. 2019. Available online: https://enterpriseiotinsights.com/20190606/channels/news/lora-and-sigfox-get-boost-with-lte-m-nb-iot-failures (accessed on 30 May 2021).
De Carvalho Silva, J.; Rodrigues, J.J.; Alberti, A.M.; Solic, P.; Aquino, A.L. LoRaWAN—A Low Power WAN Protocol for Internet of Things: A Review and Opportunities. In Proceedings of the 2nd International Multidisciplinary Conference on Computer and Energy Science (SpliTech), Split, Croatia, 12–14 July 2017; pp. 1–6. [Google Scholar]
Adelantado, F.; Vilajosana, X.; Tuset-Peiro, P.; Martinez, B.; Melia-Segui, J.; Watteyne, T. Understanding the Limits of LoRaWAN. IEEE Commun. Mag. 2017, 55, 34–40. [Google Scholar] [CrossRef] [Green Version]
Pasolini, G.; Buratti, C.; Feltrin, L.; Zabini, F.; De Castro, C.; Verdone, R.; Andrisano, O. Smart City Pilot Projects Using LoRa and IEEE 802.15.4 Technologies. Sensors 2018, 18, 1118. [Google Scholar] [CrossRef] [PubMed] [Green Version]
Miles, B.; Bourennane, E.B.; Boucherkha, S.; Chikhi, S. A Study of LoRaWAN Protocol Performance for IoT Applications in Smart Agriculture. Comput. Commun. 2020, 164, 148–157. [Google Scholar] [CrossRef]
Codeluppi, G.; Cilfone, A.; Davoli, L.; Ferrari, G. LoRaFarM: A LoRaWAN-based Smart Farming Modular IoT Architecture. Sensors 2020, 20, 2028. [Google Scholar] [CrossRef] [PubMed] [Green Version]
LoRaWAN Market Projected to Grow by 47 Percent. GPS World. 2020. Available online: https://www.gpsworld.com/lorawan-market-projected-to-grow-by-47-percent/ (accessed on 30 May 2021).
Almeida, R.; Oliveira, R.; Sousa, D.; Luis, M.; Senna, C.; Sargento, S. A Multi-Technology Opportunistic Platform for Environmental Data Gathering on Smart Cities. In Proceedings of the IEEE Globecom Workshops (GC Wkshps), Singapore, 4–8 December 2017; pp. 1–7. [Google Scholar]
Baldo, D.; Mecocci, A.; Parrino, S.; Peruzzi, G.; Pozzebon, A. A Multi-Layer LoRaWAN Infrastructure for Smart Waste Management. Sensors 2021, 21, 2600. [Google Scholar] [CrossRef] [PubMed]
Islam, B.; Islam, M.T.; Kaur, J.; Nirjon, S. LoRain: Making a Case for LoRa in Indoor Localization. In Proceedings of the IEEE International Conference on Pervasive Computing and Communications Workshops (PerCom Workshops), Kyoto, Japan, 11–15 March 2019; pp. 423–426. [Google Scholar]
Ertürk, M.A.; Aydın, M.A.; Büyükakkaşlar, M.T.; Evirgen, H. A Survey on LoRaWAN Architecture, Protocol and Technologies. Future Internet 2019, 11, 216. [Google Scholar] [CrossRef] [Green Version]
Cardell-Oliver, R.; Hübner, C.; Leopold, M.; Beringer, J. Dataset: LoRa Underground Farm Sensor Network. In Proceedings of the 2nd Workshop on Data Acquisition to Analysis, New York, NY, USA, 10 November 2019; pp. 26–28. [Google Scholar]
Bhatia, L.; Breza, M.; Marfievici, R.; McCann, J.A. Dataset: LoED: The LoRaWAN at the Edge Dataset. arXiv 2020, arXiv:2010.14211. [Google Scholar]
Aernouts, M.; Berkvens, R.; Van Vlaenderen, K.; Weyn, M. Sigfox and LoRaWAN Datasets for Fingerprint Localization in Large Urban and Rural Areas. Data 2018, 3, 13. [Google Scholar] [CrossRef] [Green Version]
Mikhaylov, K.; Stusek, M.; Masek, P.; Fujdiak, R.; Mozny, R.; Andreev, S.; Hosek, J. On the Performance of Multi-Gateway LoRaWAN Deployments: An Experimental Study. In Proceedings of the IEEE Wireless Communications and Networking Conference (WCNC), Seoul, Korea, 25–28 May 2020; pp. 1–6. [Google Scholar]
Laya, A.; Kalalas, C.; Vazquez-Gallego, F.; Alonso, L.; Alonso-Zarate, J. Goodbye, ALOHA! IEEE Access 2016, 4, 2029–2044. [Google Scholar] [CrossRef] [Green Version]
Augustin, A.; Yi, J.; Clausen, T.; Townsley, W.M. A Study of LoRa: Long Range & Low Power Networks for the Internet of Things. Sensors 2016, 16, 1466. [Google Scholar]
Reynders, B.; Meert, W.; Pollin, S. Range and Coexistence Analysis of Long Range Unlicensed Communication. In Proceedings of the 23rd International Conference on Telecommunications (ICT), Thessaloniki, Greece, 16–18 May 2016; pp. 1–6. [Google Scholar] [CrossRef] [Green Version]
LoRa Alliance. LoRaWAN 1.1 Specification. 2017. Available online: https://lora-alliance.org/wp-content/uploads/2020/11/lorawantm_specification_-v1.1.pdf (accessed on 30 May 2021).
Loy, M.; Karingattil, R.; Williams, L. ISM-Band and Short Range Device Regulatory Compliance Overview; Texas Instruments: Dallas, TX, USA, 2005; pp. 5–13. [Google Scholar]
LoRa Alliance. LoRaWAN Regional Parameters, 2020. Available online: https://lora-alliance.org/sites/default/files/2020-02/rp_2-1.0.1.pdf (accessed on 30 May 2021).
Georgiou, O.; Raza, U. Low Power Wide Area Network Analysis: Can LoRa Scale? IEEE Wirel. Commun. Lett. 2017, 6, 162–165. [Google Scholar] [CrossRef] [Green Version]
Rizzi, M.; Ferrari, P.; Flammini, A.; Sisinni, E. Evaluation of the IoT LoRaWAN Solution for Distributed Measurement Applications. IEEE Trans. Instrum. Meas. 2017, 66, 3340–3349. [Google Scholar] [CrossRef]
ERC Recommendation 70-03. 2020. Available online: https://docdb.cept.org/download/25c41779-cd6e/Rec7003e.pdf (accessed on 30 May 2021).
LoRaWAN Network Server 6.x—Uplink Data Message. Available online: https://docs.loriot.io/display/LNS/Uplink+Data+Message (accessed on 30 May 2021).
SX1301 Datasheet. 2017. Available online: https://sforce.co/3dPFtby (accessed on 30 May 2021).
Keysight Technologies. N6700 Modular Power System Family—Data Sheet. Available online: https://www.keysight.com/fi/en/assets/7018-01522/data-sheets/5989-6319.pdf (accessed on 30 May 2021).

Figure 1. The network architecture of the LoRaWAN network.

Figure 2. Summary diagram of ED’s behavior for LoRaWAN.

Figure 3. Evaluation board constructed for testing LPWA technologies.

Figure 4. Durability measurements of devices in different climatic conditions in the temperature chamber Vötsch VC3 7018.

Figure 5. Current consumption during 50 B message transmission.

Figure 6. Unconfirmed transmission power consumption.

Figure 7. Confirmed transmission power consumption.

Figure 8. Measurement locations in Brno, Czech Republic.

Figure 9. Effect of the distance to the nearest GW on the outage probability.

Figure 10. Observed relation of RSSI and distance per successfully delivered packet.

Figure 11. Observed relation of SNR and distance per successfully delivered packet.

Figure 12. Observed relation of SNR and RSSI per successfully delivered packet.

Figure 13. BUT sensor RSSI samples relative frequency histogram.

Figure 14. City center sensor RSSI samples relative frequency histogram.

Figure 15. BUT sensor SNR samples relative frequency histogram.

Figure 16. City center sensor SNR samples relative frequency histogram.

Table 1. Key parameters of LoRaWAN technology.

Parameters	Property
Coverage (MCL)	157 dB
Technology	PHY (Proprietary)/MAC (Open)
Frequency spectrum	Unlicensed/ISM
Duty cycle limitation	Yes (0.1% or 1% in EU)
Transmission power restrictions	Yes (16 dBm = 40 mW)
Data rates in Downlink (DL)	0.25–50 kbps (50 kbps with FSK)
Data rates in Uplink (UL)	0.25–50 kbps (50 kbps with FSK)
Max. message size UL	243 B
Max. message size DL	243 B
Current consumption	Sleep < 2 uA, Tx < 45 mA (14 dBm), Rx < 15 mA
Module cost	<8 USD
Security	Medium (AES-128)

Table 2. Description of LoRaWAN network architecture blocks.

End Nodes
AES	Advanced Encryption Standard used for encrypted communication.
Concentrators
TR-069	Technical specification that defines an application protocol for remote management of network devices.
MQTTS	Lightweight messaging protocol MQTT (for M2M, IoT devices) with TLS (SSL) encryption support.
HTTPS	Hypertext transfer protocol (HTTP) with encryption protocol TLS (SSL), mostly used for web browsing.
Routing Services
Network server	Implements LoRaWAN protocol, validates authenticity and integrity of devices, packet deduplication, organizes downlink transmission, and many others.
Routing server	Routes traffic based on the customer’s account and the selected server.
Database	Data storage for billing server.
Server for A, B, and C	Customer server that handles end-device join procedures, key storage, and management.
Positioning server	Provides position calculation (estimation) of end devices in the network.
Billing server	Handles the tracking of billable products and services.
GNMS	(Global network management system) Provides remote monitor and control functionality.
Oauth2	Industry-standard protocol for authorization that provides API clients limited access to user data on a web server.
App Servers
MQTT	Lightweight messaging protocol MQTT (for M2M and IoT devices).
RESTful	Architectural style for API (application program interface) that uses HTTPS requests to access and use data.
Customer-Specific API	Proprietary protocol implementation.

Table 3. EU863-870 Uplink data rate [39].

Data Rate (DR)	Configuration	Physical Bit Rate [b/s]
0	LoRa: SF12/125 kHz	250
1	LoRa: SF11/125 kHz	440
2	LoRa: SF10/125 kHz	980
3	LoRa: SF9/125 kHz	1760
4	LoRa: SF8/125 kHz	3125
5	LoRa: SF7/125 kHz	5470
6	LoRa: SF7/250 kHz	11,000
7	FSK: 50 kb/s	50,000
8–14	Reserved	-

Table 4. EU863-870 default/mandatory channels [39].

Bandwidth [kHz]	Channel Frequency [MHz]	Bit Rate [kb/s]	Duty Cycle
125	868.1, 868.3, 868.5	0.25 (DR0) to 5 (DR5)	<1%

Table 5. General specifications of the RN2483 Low-Power Wide-Area LoRaWAN technology transceiver module.

Parameter	Value
Frequency Range	863.0 MHz to 870.0 MHz; 433.050 MHz to 434.790 MHz
RF Output Power	Adjustable up to +14 dBm high Efficiency PA
Modulation Schemes	FSK, GFSK, and LoRa Technology Modulation
Data Rate	300 kbps with FSK modulation; 10,937 bps with LoRa Technology modulation
Output Power	Adjustable up to max. 10 dBm on 433 MHz band (limited to meet regulations); max. 14 dBm on the 868 MHz band
Receiver Sensitivity	Up to −146 dBm

Publisher’s Note: MDPI stays neutral with regard to jurisdictional claims in published maps and institutional affiliations.

© 2021 by the authors. Licensee MDPI, Basel, Switzerland. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC BY) license (https://creativecommons.org/licenses/by/4.0/).

Share and Cite

MDPI and ACS Style

Masek, P.; Stusek, M.; Svertoka, E.; Pospisil, J.; Burget, R.; Lohan, E.S.; Marghescu, I.; Hosek, J.; Ometov, A. Measurements of LoRaWAN Technology in Urban Scenarios: A Data Descriptor. Data 2021, 6, 62. https://doi.org/10.3390/data6060062

AMA Style

Masek P, Stusek M, Svertoka E, Pospisil J, Burget R, Lohan ES, Marghescu I, Hosek J, Ometov A. Measurements of LoRaWAN Technology in Urban Scenarios: A Data Descriptor. Data. 2021; 6(6):62. https://doi.org/10.3390/data6060062

Chicago/Turabian Style

Masek, Pavel, Martin Stusek, Ekaterina Svertoka, Jan Pospisil, Radim Burget, Elena Simona Lohan, Ion Marghescu, Jiri Hosek, and Aleksandr Ometov. 2021. "Measurements of LoRaWAN Technology in Urban Scenarios: A Data Descriptor" Data 6, no. 6: 62. https://doi.org/10.3390/data6060062

Article Menu