Search Results (303)

In this study, polysaccharides were extracted at a rate of 87.5% ± 1.5% from native dandelion roots, and the dandelion root polysaccharides (DRPs) were then chemically modified to obtain sulfated polysaccharides (SDRPs) with a degree of substitution of 1.49 ± 0.07. The effects of modification conditions, physicochemical characterizations, structural characteristics, antioxidant properties, hypoglycemic activity, and proliferative effects on probiotics of DRP derivatives were further investigated. Results showed that the optimum conditions for sulfation of DRPs included esterification reagents (concentrated sulfuric acid: n-butanol) ratio of 3:1, a reaction temperature of 0 °C, a reaction time of 1.5 h, and the involvement of 0.154 g of ammonium sulfate. The DRPs and SDRPs were composed of six monosaccharides, including mannose, glucosamine, rhamnose, glucose, galactose, and arabinose. Based on infrared spectra, the peaks of the characteristic absorption bands of S=O and C-O-S appeared at 1263 cm⁻¹ and 836 cm⁻¹. Compared with DRPs, SDRPs had a significantly lower relative molecular mass and a three-stranded helical structure. NMR analysis showed that sulfated modification mainly occurred on the hydroxyl group at C6. SDRPs underwent a chemical shift to higher field strength, with their characteristic signal peaking in the region of 1.00–1.62 ppm. Scanning electron microscopy (SEM) analysis indicated that the surface morphology of SDRPs was significantly changed. The structure of SDRPs was finer and more fragmented than DRPs. Compared with DRPs, SDRPs showed better free radical scavenging ability, higher Fe²⁺chelating ability, and stronger inhibition of α-glucosidase and α-amylase. In addition, SDRPs had an excellent promotional effect on the growth of Lactobacillus plantarum 10665 and Lactobacillus acidophilus. Therefore, this study could provide a theoretical basis for the development and utilization of DRPs. Full article

Diclofenac (DCF) is often detected in diverse aquatic bodies, and ineffective management can lead to detrimental effects on human health and ecosystems. In this study, degradation of DCF by Fe(III) and Mn(II) activating bisulfite (BS) was investigated. In the Fe(III)/Mn(II)/BS system, 93.4% DCF was degraded at 200 μM BS within 120 s, and additional research on 1000 μM BS achieved 88.4% degradation efficacy. Moreover, kinetics fitting of DCF degradation with the different BS concentrations was studied to find the two highest reaction rates (200 and 1000 μM, k_obs = 0.0297 and 0.0317 s⁻¹, respectively). Whereafter, SO₄^•− and Mn(III) were identified as the main active species at these two concentrations, respectively. Density functional theory (DFT) calculations, molecular frontier orbital theory, and surface electrostatic potential (ESP) forecast electrophilic attack sites. DCF degradation pathways by radical and non-radical ways were proposed by attack site prediction and thirteen intermediates identified by UPLC-QTOF-MS. ECOSAR software 2.2 was used for toxicity assessment. This work studied DCF degradation by the Fe(III)/Mn(II)/BS process in the presence of different concentrations of BS, providing a new insight into water purification. Full article

The objective of the present study was to assess the effect of intra-articular Hyaluronic acid (HA) and Chondroitin sulfate (CS) supplementation (Hialurom^® Hondro (HH)) on pain symptoms and joint mobility. In total, 60 mg/mL sodium hyaluronate and 90 mg/mL CS were administered to 21 patients (17 females and 4 males) respecting the in-force requirements, excluding patients with some specific comorbidities. In addition to the clinical study (where the pain intensity (severity) and joint mobility were assessed), rheological characterization was conducted evaluating the following parameters: elastic modulus (G′), loss modulus (G″) oscillatory frequency (fc) at 0.5 Hz and 2.5 Hz, crossover frequency (fc), relaxation time (λ) where it was noticed that the addition of chondroitin sulfate (CS) to sodium hyaluronate (SH) significantly enhances and improves the viscoelastic properties, particularly at higher shear frequencies. A significant decrease in pain intensity felt by the subjects was found, from 7.48 (according to Wong–Baker scale)—pain close to 8 (the patient is unable to perform most activities), to more reduced values of 5.86—at 6 weeks after injection, 4.81—at 3 months after injection, and 5.24—at 6 months after injection, improvements in symptoms was fast and durable. Data related to the evolution of joint mobility show that at 6 weeks after injection, the mobility of joints increased by 17.8% and at 6 months by 35.61%. No serious adverse events were reported with undesired effects so that they would impose additional measures. Better resistance to enzymatic degradation and free radicals could be expected from the synergic combination of sodium hyaluronate and chondroitin sodium sulfate, this having a special importance for the patients, granting them the ability to perform more ample movements and reducing dependency on attendants, thus increasing quality of life. Full article

Cryogels represent a valid strategy as scaffolds for tissue engineering. In order to adequately support adhesion and proliferation of anchorage-dependent cells, different polymers need to be combined within the same scaffold trying to mimic the complex features of a natural extracellular matrix (ECM). For this reason, in this work, gelatin (Gel) and chondroitin sulfate (CS), both functionalized with methacrylic groups to produce CSMA and GelMA derivatives, were selected to prepare cryogel networks. Both homopolymer and heteropolymer cryogels were produced, via radical crosslinking reactions carried out at −12 °C for 2 h. All the scaffolds were characterized for their mechanical, swelling and morphological properties, before and after autoclave sterilization. Moreover, they were evaluated for their biocompatibility and ability to support the adhesion of human gingival fibroblasts and tenocytes. GelMA-based homopolymer networks better withstood the autoclave sterilization process, compared to CSMA cryogels. Indeed, GelMA cryogels showed a decrease in stiffness of approximately 30%, whereas CSMA cryogels of approximately 80%. When GelMA and CSMA were blended in the same network, an intermediate outcome was observed. However, the hybrid scaffolds showed a general worsening of the biological performance. Indeed, despite their ability to withstand autoclave sterilization with limited modification of the mechanical and morphological properties, the hybrid cryogels exhibited poor cell adhesion and high LDH leakage. Therefore, not only do network components need to be properly selected, but also their combination and ability to withstand effective sterilization process should be carefully evaluated for the development of efficient scaffolds designed for tissue engineering purposes. Full article

The chemical composition of extracts (CEs) and essential oils (EOs) from Tetradenia riparia leaves, flower buds, and stems was analyzed. Antiproliferative activity against tumor cell lines, NO production inhibition, and antioxidant and antiviral activities were assessed. The CEs contained flavonoids, phenolic acids, coumarins, and saturated fatty acids. The EOs included monoterpenes, oxygenated sesquiterpenes, and diterpenes. NO production inhibition ranged from 76 to 247 µg mL⁻¹, and antiproliferative activity exhibited GI₅₀ between 20 and >204 µg mL⁻¹, with low cytotoxicity (SI: 1.08 to 4.75). Reactive oxygen species inhibition ranged from 45 to 82%. Antioxidant activity varied when determined by the 2,2-diphenyl-1-picrylhydrazyl radical scavenging assay (IC₅₀: 0.51 to 8.47 mg mL⁻¹) and ferric reducing antioxidant power (0.35 to 0.81 µM ferrous sulfate per mg). The reduction in β-carotene–linoleic acid co-oxidation varied between 76.13 and 102.25%. The total phenolic content of CEs and EOs was 10.70 to 111.68 µg gallic acid mg⁻¹. Antiviral activity against herpes simplex virus type 1 (HSV-1) showed an EC₅₀ between 9.64 and 24.55 µg mL⁻¹ and an SI between 8.67 and 15.04. Leaf EOs exhibited an EC₅₀ of 9.64 µg mL⁻¹ and an SI of 15.04. Our study unveils the diverse chemical composition and multifaceted pharmacological properties of T. riparia, demonstrating its potential as a valuable source of bioactive compounds for therapeutic applications. Full article

Sulfate radical-based advanced oxidation processes exhibit great potential for the degradation of organic pollutants. In this study, P-doped biochar (PBC500) was successfully synthesized by the pyrolysis of H₃PO₄-impregnated cow manure waste and was employed to activate peroxymonosulfate (PMS) for the elimination of 17β-estradiol (E2). The characterization results showed that the surface area, defective structure, and functional groups (C=O and phosphorus-containing groups) of biochar increased after H₃PO₄ modification. PBC500 exhibited high PMS activation activity and excellent E2 degradation capacity; 97.91% of 3 mg/L E2 can be removed within 90 min using 0.2 g/L PBC500 and 1 mM PMS. Based on the quenching experiments and X-ray photoelectron spectroscopy (XPS) analysis, defective structures, C=O, and P-C groups on biochar act as active sites to promote the catalytic oxidation of E2 by generating O₂⁻ and ¹O₂. In addition, PBC500 displayed excellent reusability, achieving 65.15% E2 degradation after three reuse cycles. Overall, this study presented a new technique that supports a high efficiency, environmentally friendly, and low cost treatment method for E2 wastewater and simultaneously provided a new option for the resource utilization of livestock waste. Full article

The removal of pesticides and other organic pollutants from water through advanced oxidation processes (AOPs) holds great promise. The main advantage of these technologies is that they remove, or at least reduce, pesticide levels by mineralization rather than transfer, as in conventional processes. This study first evaluated the effectiveness of UV/S₂O₈⁼ compared to heterogeneous photocatalysis using UV/TiO₂ processes on the degradation of two commonly used herbicides (terbuthylazine and isoproturon) in aqueous solutions using a laboratory photoreactor. In addition, the effect of the UV wavelength on the degradation efficiency of both herbicides was investigated. Although the degradation rate was greater under UV(254)/S₂O₈⁼ nm than under UV(365)/S₂O₈⁼ nm, complete degradation of the herbicides (0.2 mg L⁻¹) was achieved within 30 min under UV-366 nm using a Na₂S₂O₈ dose of 250 mg L⁻¹ in the absence of inorganic anions. To assess the impact of the water matrix, the individual and combined effects of sulfate (SO₄⁼), bicarbonate (HCO₃⁻), and chloride (Cl⁻) were evaluated. These can react with hydroxyl (HO^•) and sulfate (SO₄^•−) radicals generated during AOPs to form new radicals with a lower redox potential. The results showed negligible effects of SO₄⁼, while the combination of HCO₃⁻ and Cl⁻ seemed to be the key to the decrease in herbicide removal efficiency found when working with complex matrices. Finally, the main intermediates detected during the photodegradation process are identified, and the likely pathways involving dealkylation, dechlorination, and hydroxylation are proposed and discussed. Full article

Antibiotic resistance is a global health crisis caused by the overuse and misuse of antibiotics. Accordingly, bacteria have developed mechanisms to resist antibiotics. This crisis endangers public health systems and medical procedures, underscoring the urgent need for novel antimicrobial agents. This study focuses on the green synthesis of ZnO nanoparticles (NPs) using aqueous extracts from Nepeta nepetella subps. amethystine leaves and stems, employing different zinc sulfate concentrations (0.5, 1, and 2 M). NP characterization included transmission electron microscopy (TEM), scanning electron microscopy (SEM), and X-ray diffraction (XRD), along with Fourier transform infrared spectroscopy (FTIR) analysis. This study aimed to assess the efficacy of ZnO NPs, prepared at varying concentrations of zinc sulfate, for their capacity to inhibit both Gram-positive and Gram-negative bacteria, as well as their antioxidant potential using the 2,2-diphenyl-1-picrylhydrazyl (DPPH) method. SEM and TEM results showed predominantly spherical NPs. The smallest size (18.5 ± 1.3 nm for leaves and 18.1 ± 1.3 nm for stems) occurred with the 0.5 M precursor concentration. These NPs also exhibited remarkable antibacterial activity against both Gram-positive and Gram-negative bacteria at 10 µg/mL, as well as the highest antioxidant activity, with an IC₅₀ (the concentration of NPs that scavenge 50% of the initial DPPH radicals) of 62 ± 0.8 (µg/mL) for the leaves and 35 ± 0.6 (µg/mL) for the stems. NPs and precursor concentrations were modeled to assess their impact on bacteria using a 2D polynomial equation. Response surface plots identified optimal concentration conditions for antibacterial effectiveness against each species, promising in combating antibiotic resistance. Full article

This study evaluates, for the first time, the effects of UV/PMS and UV/H₂O₂/PMS processes on the degradation of sunscreen agents in synthetic and natural water matrices and compares their effectiveness with the more conventional UV/H₂O₂. Investigations were conducted using a mixture of organic UV filters containing 4-methylbenzylidene camphor (4-MBC) and 2-ethylhexyl-4-methoxycinnamate. Among the investigated UV-driven AOPs, UV/PMS/H₂O₂ was the most effective in synthetic water, while in natural water, the highest degradation rate was observed during the degradation of EHMC by UV/PMS. The degradation of UV filters in the UV/PMS system was promoted by sulfate radical (68% of the degradation), with hydroxyl radical contributing approximately 32%, while both radical species contributed approximately equally to the degradation in the UV/H₂O₂/PMS system. The Vibrio fischeri assay showed an increase in inhibition (up to 70%) at specific stages of UV/H₂O₂ treatment when applied to natural water, which further decreased to 30%, along with an increase in UV fluence and progressive degradation. The Pseudomonas putida test recorded minor toxicity (<15%) after treatments. Magnetic biochar utilized in conjunction with UV-driven AOPs exhibited superior performance in eliminating residual contaminants, providing an efficient and sustainable approach to mitigate sunscreen agents in water treatment. Full article

The purpose of this paper was to investigate the anti-inflammatory and anti-angiogenic activities of sulfated polysaccharide from C. tomentosum (PCT) using carrageenan (CARR)-induced paw edema in a rat model and anti-vasculogenic activity on a chorioallantoic membrane assay (CAM) model. Based on in vitro tests of anti-radical, total antioxidant, and reducing power activities, PCT presents a real interest via its antioxidant activity and ability to scavenge radical species. The in vivo pharmacological tests suggest that PCT possesses anti-inflammatory action by reducing paw edema and leukocyte migration, maintaining the redox equilibrium, and stabilizing the cellular level of several pro-/antioxidant system markers. It could significantly decrease the malondialdehyde levels and increase superoxide dismutase, glutathione peroxidase, and glutathione activities in local paw edema and erythrocytes during the acute inflammatory reaction of CARR. PCT pretreatment was effective against DNA alterations in the blood lymphocytes of inflamed rats and reduced the hematological alteration by restoring blood parameters to normal levels. The anti-angiogenic activity results revealed that CAM neovascularization, defined as the formation of new vessel numbers and branching patterns, was decreased by PCT in a dose-dependent manner, which supported the in silico bioavailability and pharmacokinetic findings. These results indicated the therapeutic effects of polysaccharides from C. tomentosum and their possible use as anti-proliferative molecules based on their antioxidant, anti-inflammatory, and anti-angiogenic activities. Full article

Arabinogalactan (AG), extracted from larch wood, is a β-1,3-galactan backbone and β-1,6-galactan side chains with attached α-1-arabinofuranosyl and β-1-arabinopyranosyl residues. Although the structural characteristics of arabinogalactan II type have already been studied, its functionalization using 2,2,6,6-tetramethylpiperidin-1-oxyl (TEMPO) oxidation remains a promising avenue. In this study, the oxidation of AG, a neutral polysaccharide, was carried out using the TEMPO/NaBr/NaOCl system, resulting in polyuronides with improved functional properties. The oxidation of AG was controlled by analyzing portions of the reaction mixture using spectrophotometric and titration methods. To determine the effect of the TEMPO/NaBr/NaOCl system, air-dried samples of native and oxidized AG were studied by Fourier-transform infrared (FTIR) and nuclear magnetic resonance (NMR) spectroscopy, as well as by gel permeation chromatography. Compounds that model free (1,1-diphenyl-2-picrylhydrazyl (DPPH)) and hydroxyl radicals (iron(II) sulfate, hydrogen peroxide, and salicylic acid) were used to study the antioxidant properties. It was found that, in oxidized forms of AG, the content of carboxyl groups increases by 0.61 mmol compared to native AG. The transformation of oxidized AG into the H⁺ form using a strong acid cation exchanger leads to an increase in the number of active carboxyl groups to 0.76 mmol. Using FTIR spectroscopy, characteristic absorption bands (1742, 1639, and 1403 cm⁻¹) were established, indicating the occurrence of oxidative processes with a subsequent reduction in the carboxyl group. The functionality of AG was also confirmed by gel permeation chromatography (GPC), which is reflected in an increase in molecular weights (up to 15,700 g/mol). A study of the antioxidant properties of the oxidized and protonated forms of AG show that the obtained antioxidant activity (AOA) values are generally characteristic of polyuronic acids. Therefore, the TEMPO oxidation of AG and other neutral polysaccharides can be considered a promising approach for obtaining compounds with the necessary controlled characteristics. Full article

This paper review presents a comparison between conventional leaching and advanced photochemical leaching processes and their potential for use in chalcopyrite leaching. Likewise, it presents an analysis of the differences between the advanced leaching processes, photoleaching and radical-leaching, indicating that the photochemical mechanisms (photooxidation/photoreduction and generation of radical oxygen species (ROS) and radical sulfur species (RSS)) would improve the oxidative dissolution of chalcopyrite, taking advantage of the high oxidizing power of free radicals. Initial experimental results of solar-assisted radical-leaching on chalcopyrite are presented, demonstrating that sulfate radicals (SO₄⁻) allow copper to be leached at a rate 4.7 times higher than in the absence of radicals and sunlight. With these results, a radical-leaching process is presented for the first time, with a perspective toward the future development of a new hydrometallurgical route: solar-assisted radical-leaching. Full article

Levofloxacin (LFX), which is difficult to degrade effectively due to its molecular stability, has become an problem that needs to be solved urgently. The advanced oxidation technology of persulfate has received increasing attention from researchers. In this study, a Ce-MOF derivative (Ce-MOF-T) was prepared by hydrothermal synthesis and calcination, which synergistically responded to electroactivation to generate sulfate radicals for the efficient degradation of LFX. It has been proven that electrical activation and the Ce-MOF derivatives work together to generate sulfate radicals and effectively degrade LFX. Ce-MOF-550-modified carbon cloth was used as the cathode and a platinum electrode as the anode, the concentration of LFX was 20 mg·L⁻¹, the loading of Ce-MOF-550 was 15 mg, pH = 5, the concentration of sodium persulfate (PMS) was 0.3 g·L⁻¹, the current density was 100 A·m⁻², and the degradation rate was 82.05% after 1 h of reaction and 95% after 3 h of reaction. After five cycle tests, the degradation rate was still higher than 75.00%, indicating that the material had good stability. In addition, the degradation of LFX was consistent with a quasi-primary kinetic reaction with apparent rate constants of 2.26 × 10⁻² min⁻¹. Full article

In this study, the release of proteins and other biomolecules into an aqueous media from two red macroalgae (Sphaerococcus coronopifolius and Gelidium spinosum) was studied using eight different cell disruption techniques. The contents of carbohydrates, pigments, and phenolic compounds coextracted with proteins were quantified. In addition, morphological changes at the cellular level in response to the different pretreatment methods were observed by an optical microscope. Finally, the antioxidant capacity of obtained protein extracts was evaluated using three in vitro tests. For both S. coronopifolius and G. spinosum, ultrasonication for 60 min proved to be the most effective technique for protein extraction, yielding values of 3.46 ± 0.06 mg/g DW and 9.73 ± 0.41 mg/g DW, respectively. Furthermore, the highest total contents of phenolic compounds, flavonoids, and carbohydrates were also recorded with the same method. However, the highest pigment contents were found with ultrasonication for 15 min. Interestingly, relatively high antioxidant activities like radical scavenging activity (31.57–65.16%), reducing power (0.51–1.70, OD at 700 nm), and ferrous iron-chelating activity (28.76–61.37%) were exerted by the different protein extracts whatever the pretreatment method applied. This antioxidant potency could be attributed to the presence of polyphenolic compounds, pigments, and/or other bioactive substances in these extracts. Among all the used techniques, ultrasonication pretreatment for 60 min appears to be the most efficient method in terms of destroying the macroalgae cell wall and extracting the molecules of interest, especially proteins. The protein fractions derived from the two red macroalgae under these conditions were precipitated with ammonium sulfate, lyophilized, and their molecular weight distribution was determined using SDS-PAGE. Our results showed that the major protein bands were observed between 25 kDa and 60 kDa for S. coronopifolius and ranged from 20 kDa to 150 kDa for G. spinosum. These findings indicated that ultrasonication for 60 min could be sufficient to disrupt the algae cells for obtaining protein-rich extracts with promising biological properties, especially antioxidant activity. Full article

Micropollutants belong to various groups of chemicals. One of the most diverse and large group of them are pharmaceuticals. The presence of pharmaceutical residues in wastewater poses a significant challenge to water quality and environmental health. This paper provides an overview of recent advancements in the removal of pharmaceuticals from water, focusing on various treatment processes and their effectiveness in eliminating micropollutants. Through a review of the literature, including studies on ozonation, UV irradiation, sulfate radical-based technologies, and photocatalytic processes, insights into degradation mechanisms and optimal conditions for their removal are synthesized. Additionally, with new legislation mandating the monitoring of selected micropollutants and the implementation of quaternary treatment in wastewater treatment plants, the paper discusses prospects for future research and recommendations for effective pharmaceutical removal. Key actions include conducting comprehensive laboratory and pilot trials, implementing quaternary treatment of wastewater, continuously monitoring water quality, investing in research and development, and promoting collaboration and knowledge sharing among stakeholders. By embracing these strategies, we can work towards safeguarding water resources and protecting public health from the adverse effects of pharmaceutical contamination. Full article