Search Results (48,039)

The treatment of damaged enamel surfaces involves modification of the enamel surface with artificial materials or the development of a pseudo-enamel, with research focusing on bioactive and biomimetic materials. In this study, a bioactive auto-polymerizing resin (APR) was developed by adding surface-pre-reacted glass ionomer (S-PRG) fillers of different quantities to APR. Its bioactive effects were evaluated via pH neutralization, ion release, and inhibition of enamel demineralization studies. The pH and fluoride ion release were measured using ion-specific electrodes, revealing that the APR disk with the S-PRG filler immediately neutralized the lactic acid solution (pH 4.0) through ion release. Inductively coupled plasma atomic emission spectrometry revealed that the Sr ion release peaked on the first day, with the other ions following the order F > B > Si > Al > Na, exhibiting a weekly decrease in the same order. Scanning electron microscopy was used to examine the enamel block morphology of the disks after 7 d of incubation, revealing enamel demineralization in disks without the S-PRG filler, whereas no demineralization occurred in disks with the S-PRG filler. APR containing the S-PRG filler demonstrated acid buffering suppressed enamel demineralization and bioactive properties. Full article

Background: In the pursuit of sustainable energy sources, residual biomass has emerged as a promising renewable resource. However, efficiently managing residual biomass poses significant challenges, particularly in optimizing supply chain operations. Advanced modeling approaches are necessary to address these complexities. This study aims to develop a comprehensive methodological framework for creating simulation models tailored to agroforestry residual biomass supply chains. Methods: The study employs a hybrid simulation approach, integrating geographic information system mapping with a case study analysis. The simulation was conducted over a 365-day period, using the anyLogistix software to model various supply chain dynamics. The framework also accounts for financial, operational, customer satisfaction, and environmental metrics. Results: The simulation results showed a total expenditure of EUR 5,219,411.3, with transportation being the primary cost driver, involving 5678 trips and a peak capacity of 67.16 m³. CO₂ emissions were measured at 487.7 kg/m³. The model performed as expected, highlighting the need for sustainable logistics strategies to reduce costs, lower losses, and improve productivity. Conclusions: This study presents one of the first detailed methodological frameworks for simulating agroforestry residual biomass supply chains. It provides valuable managerial insights into the financial, operational, and environmental aspects of supply chain management. The findings may stakeholders make informed decisions to enhance the sustainability of biomass utilization in energy production. Full article

Greek wines excel in quality and exports, but the viticultural sector faces significant challenges from complex supply chains, shifting European policies, and the growing need for sustainability amidst climate change and economic pressures. External environmental costs could affect significantly the decision-making process of farmers, reflecting a broader evaluation of sustainability in viticulture. This study evaluates the economic and environmental impacts of organic, integrated, and conventional viticulture management systems in Drama, Greece using a life cycle (LC) approach and data envelopment analysis (DEA) to determine efficiency, quantify environmental impacts in monetary terms, and incorporate these costs into the analysis. Organic management systems have lower energy consumption and emissions compared to integrated and conventional systems, with organic systems ranging from 4546 to 6573 kWh/ha in energy use and 1358 to 1795 kg CO₂ eq./ha in emissions, while integrated and conventional systems range from 9157 to 12,109 kWh/ha and 2961 to 3661 kg CO₂ eq./ha. The DEA analysis reveals that most organic systems perform efficiently when accounting for environmental costs, whereas conventional systems face significant efficiency declines, with only a few maintaining optimal performance. Policy-supported transitions based on the provider gets principle are crucial for balancing economic and environmental goals in viticulture, as the integration of shadow prices significantly impacts efficiency. Full article

Green finance, defined as channeling money into sustainable development activities, is still far lower than needed to achieve net-zero emissions objectives. In this paper, we discuss the role of technologies in developing green finance. We identify that green finance faces three major challenges, including the risk management of green projects, the scarcity of innovative green financing products, and compliance with the regulations. Then, in the context of the existing literature, we explore recent technologies, including blockchain, artificial intelligence (AI), machine learning (ML), data analytics, Internet of Things (IoT), and robotics that are helping to deal with the challenges in green finance. We show that data-driven approaches utilizing AI and ML help in the risk assessment of green projects; FinTech-based crowdfunding platforms provide innovative green financial products and regulatory technologies (RegTech) support in compliance with regulations. We also identify that the environmental footprint of cryptocurrencies is an emerging area in the technologies and green finance domain. Our framework could be helpful to further extend the debate on the role of technology in green finance. Full article

The European Parliament adopted a legislative resolution of 10 April 2024 on the proposal for a directive of the European Parliament and of the Council concerning urban wastewater treatment. The reduction in pollution in discharged treated wastewater in the parameters of BOD₅, total nitrogen, and total phosphorus was emphasized. Based on these results, it stated that the impacts on the quality of lakes, rivers, and seas in the EU are visible and tangible. At the same time, it was emphasized that the sector of urban wastewater removal and treatment is responsible for 0.8% of total electricity consumption and about 0.86% of all greenhouse gas emissions in the entire EU. Almost a third of these emissions could be prevented by improving the treatment process, better use of sewage sludge, and increasing energy efficiency, as well as a higher rate of use of renewable resource technologies. It is also necessary to integrate treatment processes into the circular economy. Sludge management and water reuse are suboptimal as too many valuable resources are still being wasted. This article focuses on sustainable municipal wastewater treatment, innovative and new wastewater treatment processes and technologies (combined and hybrid processes, ANAMMOX, etc.) and their use in practice with the aim of increasing environmental and energy efficiency and reducing the carbon footprint. The research is focused on the possibilities of increasing the efficiency of energy processing of sludge, reuse of nitrogen and phosphorus, sludge, and reuse of treated wastewater. Full article

This article presents a 3D model of a yellow hydrogen generation system that uses the electricity produced by a photovoltaic carport. The 3D models of all key system components were collected, and their characteristics were described. Based on the design of the 3D model of the photovoltaic carport, the amount of energy produced monthly was determined. These quantities were then applied to determine the production of low-emission hydrogen. In order to increase the amount of low-emission hydrogen produced, the usage of a stationary energy storage facility was proposed. The Metalog family of probability distributions was adopted to develop a strategic model for low-emission hydrogen production. The hydrogen economy of a company that uses small amounts of hydrogen can be based on such a model. The 3D modeling and calculations show that it is possible to design a compact low-emission hydrogen generation system using rapid prototyping tools, including the photovoltaic carport with an electrolyzer placed in the container and an energy storage facility. This is an effective solution for the climate and energy transition of companies with low hydrogen demand. In the analytical part, the Metalog probability distribution family was employed to determine the amount of monthly energy produced by 6.3 kWp photovoltaic systems located in two European countries: Poland and Italy. Calculating the probability of producing specific amounts of hydrogen in two European countries is an answer to a frequently asked question: In which European countries will the production of low-emission hydrogen from photovoltaic systems be the most profitable? As a result of the calculations, for the analyzed year 2023 in Poland and Italy, specific answers were obtained regarding the probability of monthly energy generation and monthly hydrogen production. Many companies from Poland and Italy are taking part in the European competition to create hydrogen banks. Only those that offer low-emission hydrogen at the lowest prices will receive EU funding. Full article

Residential and commercial buildings are responsible for 35% of the EU energy-related greenhouse gas (GHG) emissions. Reducing their emissions is crucial for meeting the challenging EU objective of the agenda for becoming a net-zero continent by 2050. The diffusion and integration of distributed renewable energy sources (RESs) and energy storage systems (ESSs), as well as the creation of energy communities (ECs), have proven to be crucial aspects in reducing GHG emissions. In this context, this article proposes a multi-agent AI-based control framework to solve the EC’s energy management problem in the presence of distributed RESs and ESSs as well as considering a shared ESS. The objectives of the proposed control framework are to satisfy the EC members’ load demand to maximize self-consumption and to manage ESSs charging and discharging processes, to enforce cooperative behavior among the EC members by adopting fair and personalized strategies and to maximize EC members’ profits. The proposed control procedure is based on three sequential stages, each solved by a dedicated local RL agent exploiting the Q-Learning algorithm. To reduce the computational complexity of the proposed approach, specifically defined state aggregation criteria were defined to map the RL agents’ continuous state spaces into discrete state spaces of limited dimensions. During the training phase, the EC members’ profiles and the ESSs’ and RESs’ characteristics were randomly changed to allow the RL agents to learn the correct policy to follow in any given scenario. Simulations proved the effectiveness of the proposed approach for different costumers’ load demand profiles and different EC configurations. Indeed, the trained RL agents proved to be able to satisfy the EC members’ load demands to maximize self-consumption, to correctly use the distributed and shared ESSs, to charge them according to respective personalized criteria and to sell the energy surplus, prioritizing sales to the EC. The proposed control framework also proved to be a useful tool for understanding EC performance in different configurations and, thus, for properly dimensioning the EC elements. Full article

Waste incineration has become the main treatment method for urban household waste, and it can produce a large amount of electricity. The efficiency of waste incineration plants is reduced due to the large amount of waste heat carried away by the flue gas. Recycling and utilizing the waste heat from flue gas are important in improving the economic benefits of waste incineration, which is necessary for energy conservation and emission reduction. Based on the principle of cascade waste heat recovery from waste incineration flue gas whilst considering system safety and efficiency, this study proposed a new combination cascade waste heat recovery system consisting of a Rankine cycle, an organic Rankine cycle and a heat pump cycle. Thermodynamic and economic analyses of the combined system were conducted in detail. The results indicated that the energy efficiency of the combined system could reach up to 73%. The maximum net present value of the system was million USD 1.59 million, and the dynamic investment payback period was about 6.5 years. The isentropic efficiency of the combined system’s pumps and turbines had a significant impact on the system’s performance. A higher isentropic efficiency resulted in better system performance. The exergy analysis showed that the evaporator of the heat pump system had the highest irreversible loss. Full article

In this study, silver nanoparticles (AgNPs) were synthesized using a green method from an extract of the edible insect Oxya chinensis sinuosa (O_extract). The formation of AgNPs (O_AgNPs) was confirmed via UV–vis spectroscopy, and their stability was assessed using Turbiscan analysis. The size and morphology of the synthesized particles were characterized using transmission electron microscopy and field-emission scanning electron microscopy. Dynamic light scattering and zeta potential analyses further confirmed the size distribution and dispersion stability of the particles. The average particle size was 111.8 ± 1.5 nm, indicating relatively high stability. The synthesized O_AgNPs were further characterized using X-ray photoelectron spectroscopy (XPS), high-resolution X-ray diffraction (HR-XRD), and Fourier transform infrared (FTIR) spectroscopy. XPS analysis confirmed the chemical composition of the O_AgNP surface, whereas HR-XRD confirmed its crystallinity. FTIR analysis suggested that the O_extract plays a crucial role in the synthesis process. The antibacterial activity of the O_AgNPs was demonstrated using a disk diffusion assay, which revealed effective activity against common foodborne pathogens, including Salmonella Typhimurium, Escherichia coli, Staphylococcus aureus, and Bacillus cereus. O_AgNPs exhibited clear antibacterial activity, with inhibition zones of 15.08 ± 0.45 mm for S. Typhimurium, 15.03 ± 0.15 mm for E. coli, 15.24 ± 0.66 mm for S. aureus, and 13.30 ± 0.16 mm for B. cereus. These findings suggest that the O_AgNPs synthesized from the O_extract have potential for use as antibacterial agents against foodborne bacteria. Full article

The significance of the transportation sector, notably in terms of the carbon emission factor, is an undeniable fact. Along with this fact, individuals’ transportation preferences depend on their income levels. In this context, when the issue is considered, the income level in the USA pushes people toward cheap air travel. The main reason for this is that it is cheap, accessible, and transports one to their destinations quickly. Thus, from the perspective of road transportation, bus transportation is popular among the public. The reason why both air and road transportation modes are empirically evaluated together through income distribution is due to the preference of the US people. In this context, the effectiveness of active transportation on both air and highways in the USA from 1975 to 2023 is investigated by taking into consideration the income distribution. Empirical findings obtained through the FMOLS, DOLS, CCR, and NARDL models demonstrate that all independent variables, including GDP, energy use, air transportation, and the Gini coefficient, affect carbon dioxide emissions. In addition, wavelet analysis is performed to comprehend the form of and fluctuations in the series, which are vital to monitoring the periodical changes. Full article

Global biomass burning represents a significant source of carbon emissions, exerting a substantial influence on the global carbon cycle and climate change. As global carbon emissions become increasingly concerning, accurately quantifying the carbon emissions from biomass burning has emerged as a pivotal and challenging area of scientific research. This paper presents a comprehensive review of the primary monitoring techniques for carbon emissions from biomass burning, encompassing both bottom-up and top-down approaches. It examines the current status and limitations of these techniques in practice. The bottom-up method primarily employs terrestrial ecosystem models, emission inventory methods, and fire radiation power (FRP) techniques, which rely on the integration of fire activity data and emission factors to estimate carbon emissions. The top-down method employs atmospheric observation data and atmospheric chemical transport models to invert carbon emission fluxes. Both methods continue to face significant challenges, such as limited satellite resolution affecting data accuracy, uncertainties in emission factors in regions lacking ground validation, and difficulties in model optimization due to the complexity of atmospheric processes. In light of these considerations, this paper explores the prospective evolution of carbon emission monitoring technology for biomass burning, with a particular emphasis on the significance of high-precision estimation methodologies, technological advancements in satellite remote sensing, and the optimization of global emission inventories. This study aims to provide a forward-looking perspective on the evolution of carbon emission monitoring from biomass burning, offering a valuable reference point for related scientific research and policy formulation. Full article

Polycyclic aromatic hydrocarbons (PAHs) are a group of organic compounds that are both toxic and hazardous to human health and ecological systems. In recent work, a novel analytical strategy based on the chemometric-assisted HPLC-DAD method was proposed for the quantification and source apportionment of eight PAHs in PM10 samples. Compared to traditional chromatographic methods, this approach does not require the purification of complex PM10 samples. Instead, it utilizes a mathematical separation method to extract analytes’ profiles from overlapping chromatographic peaks, enabling precise quantification of PAHs in PM10. Firstly, 40 PM10 samples collected in Loudi city during two sampling periods were used for analysis. Subsequently, the second-order calibration method based on alternating trilinear decomposition (ATLD) was employed to handle the three-way HPLC-DAD data. Finally, the pollution sources of PAHs were analyzed by the feature component analysis method according to the obtained relative concentration matrix. For the validation model, the average recoveries of eight PAHs were between (88.8 ± 7.6)% and (105.6 ± 7.5)%, and the root-mean-square errors of prediction ranged from 0.03 μg mL⁻¹ to 0.47 μg mL⁻¹. The obtained limits of quantification for eight PAHs were in the range of 0.0050 μg mL⁻¹ to 0.079 μg mL⁻¹. For actual PM10 samples, results of the feature component analysis indicated that the main source of PAHs in PM10 may be traffic emissions and coal combustion. In summary, the proposed method provided a new and rapid analysis method for the accurate determination and source apportionment of PAHs in atmospheric aerosols. Full article

The emission of toxic gases from industrial production has intensified issues related to atmospheric pollution and human health. Consequently, the effective real-time monitoring and removal of these harmful gases have emerged as significant challenges. In this work, the density functional theory (DFT) method was utilized to examine the adsorption behaviors and electronic properties of the Ni-decorated InSe (Ni-InSe) monolayer when interacting with twelve gases (CO, NO, NO₂, NH₃, SO₂, H₂S, H₂O, CO₂, CH₄, H₂, O₂, and N₂). A comparative assessment of adsorption strength and sensing properties was performed through analyses of the electronic structure, work function, and recovery time. The results show that Ni doping enhances the electrical conductivity of the InSe monolayer and improves the adsorption capabilities for six toxic gases (CO, NO, NO₂, NH₃, SO₂, and H₂S). Furthermore, the adsorption of these gases on the Ni-InSe surface is characterized as chemisorption, as indicated by the analysis of the adsorption energy, density of states, and charge density difference. Additionally, the adsorption of CO, NO, NO₂, and SO₂ results in significant alterations to the bandgap of Ni-InSe, with changes of 18.65%, 11.37%, 10.62%, and −31.77%, respectively, underscoring its exceptional sensitivity. Moreover, the Ni-InSe monolayer exhibits a moderate recovery time of 3.24 s at 298 K for the SO₂. Consequently, the Ni-InSe is regarded as a promising gas sensor for detecting SO₂ at room temperature. This research establishes a foundation for the development of an Ni-InSe-based gas sensor for detecting and mitigating harmful gas emissions. Full article

Microalgae are considered to be a promising and prospective source of lipids for the production of biocomponents for conventional liquid fuels. The available sources contain a lot of information about the cultivation of biomass and the amounts and composition of the resulting bio-oils. However, there is a lack of reliable and verified data on the impact of fuel blends based on microalgae biodiesel on the quality of the emitted exhaust gas. Therefore, the main objective of the study was to present the emission characteristics of a compression-ignition engine fuelled with a blend of diesel fuel and biodiesel produced from the lipids accumulated in the biomass of a heterotrophic culture of Schizochytrium sp. The final concentrations of microalgal biomass and lipids in the culture were 140.7 ± 13.9 g/L and 58.2 ± 1.1 g/L, respectively. The composition of fatty acids in the lipid fraction was dominated by decosahexaenoic acid (43.8 ± 2.8%) and palmitic acid (40.4 ± 2.8%). All parameters of the bio-oil met the requirements of the EN 14214 standard. It was found that the use of bio-components allowed lower concentrations of hydrocarbons in the exhaust gas, ranging between 33 ± 2 ppm and 38 ± 7 ppm, depending on the load level of the engine. For smoke opacity, lower emissions were found in the range of 50–100% engine load levels, where the observed content was between 23 ± 4% and 53 ± 8%. Full article

Gas boilers exhibit thermal inefficiency and unsatisfying pollutant emissions. In this study, numerical simulations were conducted to examine the effect of humidified oxygen-enriched air on methane combustion in a furnace and the effects of different premixed ratios of air on the temperature field inside the furnace, intermediate product OH groups, component concentration distribution, and pollutants. Although humidification of ambient air effectively reduced the flame center temperature and mass concentration of the NOx generated during combustion in the furnace, the highest growth rate of CO concentration at the furnace outlet was 18.6%. Humidification of oxygen-enriched air increased the center temperature and outlet NO concentration of the furnace compared with those during no oxygen enrichment, but the outlet CO concentration showed a decreasing trend, with the highest decrease rate of 34.6%. This study determined an optimal CO–air premix ratio with a moisture concentration of 50 g/kg dry air and an oxygen concentration of 23%. The air humidification and oxygen enrichment technology proposed in this article provides a technical reference for low nitrogen transformation of existing gas boilers. Full article