Micropython for Nucleo-68 WB55 #17024

mkphsnbng · 2025-03-28T02:37:02Z

mkphsnbng
Mar 28, 2025

Hi,

I am trying to run micro python in Nucleo-68 STM32WB55R6VG.

I followed the link https://docs.micropython.org/en/latest/develop/gettingstarted.html#building-the-stm32-port

I am able to generate the binary files(hex,dfu,bin,elf)

I flashed firmware.bin file to 0x08000000.. and reset the board i am not able to see the REPL python on serial COM port(STLINK virtual COM port )

to verify wether serial port is configured correctly or not i print message in my project and able to observe log which we have printed.

but we are not able to observe the REPL in the same console.. (COM port)

to cross verify i have build mboot binary too and flashed in 0x08000000 and firmware.bin into 0x08000000

but still not able to get REPL prompt

Request to please help on this

mkphsnbng · 2025-03-28T09:13:22Z

mkphsnbng
Mar 28, 2025
Author

Hi , I have attached please have a look and suggest.. Regards, Manu From: Dave Festing ***@***.***> Sent: Friday, March 28, 2025 2:24 PM To: micropython/micropython ***@***.***> Cc: Kumar, Manu (FT D IN PAMC MI EMB FW) ***@***.***>; Author ***@***.***> Subject: Re: [micropython/micropython] Micropython for Nucleo-68 WB55 (Discussion #17024) Could you post the mpconfigboard.h that you are building against? - Reply to this email directly, view it on GitHub<#17024 (comment)>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/A6LDIRJ3T3THASE36OMUEYT2WUE3TAVCNFSM6AAAAABZ6PC6AGVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTENRVGA2DKMI>. You are receiving this because you authored the thread.Message ID: ***@***.***> /* * This file is part of the MicroPython project, http://micropython.org/ * * The MIT License (MIT) * * Copyright (c) 2013-2017 Damien P. George * * Permission is hereby granted, free of charge, to any person obtaining a copy * of this software and associated documentation files (the "Software"), to deal * in the Software without restriction, including without limitation the rights * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell * copies of the Software, and to permit persons to whom the Software is * furnished to do so, subject to the following conditions: * * The above copyright notice and this permission notice shall be included in * all copies or substantial portions of the Software. * * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN * THE SOFTWARE. */ // Options to control how MicroPython is built for this port, // overriding defaults in py/mpconfig.h. // board specific definitions #include "mpconfigboard.h" #include "mpconfigboard_common.h" #ifndef MICROPY_CONFIG_ROM_LEVEL #define MICROPY_CONFIG_ROM_LEVEL (MICROPY_CONFIG_ROM_LEVEL_EXTRA_FEATURES) #endif // memory allocation policies #ifndef MICROPY_GC_STACK_ENTRY_TYPE #if MICROPY_HW_SDRAM_SIZE #define MICROPY_GC_STACK_ENTRY_TYPE uint32_t #else #define MICROPY_GC_STACK_ENTRY_TYPE uint16_t #endif #endif #define MICROPY_ALLOC_PATH_MAX (128) // optimisations #ifndef MICROPY_OPT_COMPUTED_GOTO #define MICROPY_OPT_COMPUTED_GOTO (1) #endif // Don't enable lookup cache on M0 (low RAM) #ifndef MICROPY_OPT_MAP_LOOKUP_CACHE #define MICROPY_OPT_MAP_LOOKUP_CACHE (__CORTEX_M > 0) #endif // emitters #define MICROPY_PERSISTENT_CODE_LOAD (1) #ifndef MICROPY_EMIT_THUMB #define MICROPY_EMIT_THUMB (1) #endif #ifndef MICROPY_EMIT_INLINE_THUMB #define MICROPY_EMIT_INLINE_THUMB (1) #endif // Python internal features #define MICROPY_TRACKED_ALLOC (MICROPY_SSL_MBEDTLS || MICROPY_BLUETOOTH_BTSTACK) #define MICROPY_READER_VFS (1) #define MICROPY_ENABLE_GC (1) #define MICROPY_ENABLE_EMERGENCY_EXCEPTION_BUF (1) #define MICROPY_EMERGENCY_EXCEPTION_BUF_SIZE (0) #define MICROPY_REPL_INFO (1) #define MICROPY_LONGINT_IMPL (MICROPY_LONGINT_IMPL_MPZ) #ifndef MICROPY_FLOAT_IMPL // can be configured by each board via mpconfigboard.mk #define MICROPY_FLOAT_IMPL (MICROPY_FLOAT_IMPL_FLOAT) #endif #define MICROPY_USE_INTERNAL_ERRNO (1) #define MICROPY_SCHEDULER_STATIC_NODES (1) #define MICROPY_SCHEDULER_DEPTH (8) #define MICROPY_VFS (1) #ifndef MICROPY_VFS_ROM #define MICROPY_VFS_ROM (MICROPY_HW_ROMFS_ENABLE_INTERNAL_FLASH || MICROPY_HW_ROMFS_ENABLE_EXTERNAL_QSPI) #endif // control over Python builtins #ifndef MICROPY_PY_BUILTINS_HELP_TEXT #define MICROPY_PY_BUILTINS_HELP_TEXT stm32_help_text #endif #ifndef MICROPY_PY_SYS_PLATFORM // let boards override it if they want #define MICROPY_PY_SYS_PLATFORM "pyboard" #endif #ifndef MICROPY_PY_THREAD #define MICROPY_PY_THREAD (0) #endif // extended modules #define MICROPY_PY_HASHLIB_MD5 (MICROPY_PY_SSL) #define MICROPY_PY_HASHLIB_SHA1 (MICROPY_PY_SSL) #define MICROPY_PY_CRYPTOLIB (MICROPY_PY_SSL) #define MICROPY_PY_OS_INCLUDEFILE "ports/stm32/modos.c" #define MICROPY_PY_OS_DUPTERM (3) #define MICROPY_PY_OS_DUPTERM_BUILTIN_STREAM (1) #define MICROPY_PY_OS_DUPTERM_STREAM_DETACHED_ATTACHED (1) #define MICROPY_PY_OS_SYNC (1) #define MICROPY_PY_OS_UNAME (1) #define MICROPY_PY_OS_URANDOM (MICROPY_HW_ENABLE_RNG) #define MICROPY_PY_RANDOM_SEED_INIT_FUNC (rng_get()) #define MICROPY_PY_TIME_GMTIME_LOCALTIME_MKTIME (1) #define MICROPY_PY_TIME_TIME_TIME_NS (1) #define MICROPY_PY_TIME_INCLUDEFILE "ports/stm32/modtime.c" #define MICROPY_PY_LWIP_PPP (MICROPY_PY_NETWORK_PPP_LWIP) #define MICROPY_PY_LWIP_SOCK_RAW (MICROPY_PY_LWIP) #ifndef MICROPY_PY_MACHINE #define MICROPY_PY_MACHINE (1) #define MICROPY_PY_MACHINE_INCLUDEFILE "ports/stm32/modmachine.c" #define MICROPY_PY_MACHINE_RESET (1) #define MICROPY_PY_MACHINE_BARE_METAL_FUNCS (1) #define MICROPY_PY_MACHINE_FREQ_NUM_ARGS_MAX (4) #define MICROPY_PY_MACHINE_BOOTLOADER (1) #define MICROPY_PY_MACHINE_ADC (1) #define MICROPY_PY_MACHINE_ADC_INCLUDEFILE "ports/stm32/machine_adc.c" #ifndef MICROPY_PY_MACHINE_BITSTREAM #define MICROPY_PY_MACHINE_BITSTREAM (1) #endif #define MICROPY_PY_MACHINE_DHT_READINTO (1) #define MICROPY_PY_MACHINE_PULSE (1) #define MICROPY_PY_MACHINE_PIN_MAKE_NEW mp_pin_make_new #define MICROPY_PY_MACHINE_I2C (MICROPY_HW_ENABLE_HW_I2C) #define MICROPY_PY_MACHINE_SOFTI2C (1) #define MICROPY_PY_MACHINE_I2S_INCLUDEFILE "ports/stm32/machine_i2s.c" #define MICROPY_PY_MACHINE_I2S_CONSTANT_RX (I2S_MODE_MASTER_RX) #define MICROPY_PY_MACHINE_I2S_CONSTANT_TX (I2S_MODE_MASTER_TX) #define MICROPY_PY_MACHINE_I2S_RING_BUF (1) #define MICROPY_PY_MACHINE_SPI (1) #define MICROPY_PY_MACHINE_SPI_MSB (SPI_FIRSTBIT_MSB) #define MICROPY_PY_MACHINE_SPI_LSB (SPI_FIRSTBIT_LSB) #define MICROPY_PY_MACHINE_SOFTSPI (1) #define MICROPY_PY_MACHINE_TIMER (1) #define MICROPY_PY_MACHINE_UART (1) #define MICROPY_PY_MACHINE_UART_INCLUDEFILE "ports/stm32/machine_uart.c" #define MICROPY_PY_MACHINE_UART_IRQ (1) #define MICROPY_PY_MACHINE_UART_READCHAR_WRITECHAR (1) #define MICROPY_PY_MACHINE_UART_SENDBREAK (1) #define MICROPY_PY_MACHINE_WDT (1) #define MICROPY_PY_MACHINE_WDT_INCLUDEFILE "ports/stm32/machine_wdt.c" #endif #define MICROPY_HW_SOFTSPI_MIN_DELAY (0) #define MICROPY_HW_SOFTSPI_MAX_BAUDRATE (HAL_RCC_GetSysClockFreq() / 48) #define MICROPY_PY_WEBSOCKET (MICROPY_PY_LWIP) #define MICROPY_PY_WEBREPL (MICROPY_PY_LWIP) #ifndef MICROPY_PY_NETWORK #define MICROPY_PY_NETWORK (1) #endif #ifndef MICROPY_PY_ONEWIRE #define MICROPY_PY_ONEWIRE (1) #endif // optional network features #if MICROPY_PY_NETWORK #ifndef MICROPY_PY_SOCKET #define MICROPY_PY_SOCKET (1) #endif #ifndef MICROPY_PY_NETWORK_PPP_LWIP #define MICROPY_PY_NETWORK_PPP_LWIP (0) #endif #endif // fatfs configuration used in ffconf.h #define MICROPY_FATFS_ENABLE_LFN (2) #define MICROPY_FATFS_LFN_CODE_PAGE 437 /* 1=SFN/ANSI 437=LFN/U.S.(OEM) */ #define MICROPY_FATFS_USE_LABEL (1) #define MICROPY_FATFS_RPATH (2) #define MICROPY_FATFS_MULTI_PARTITION (1) #if MICROPY_PY_PYB extern const struct _mp_obj_module_t pyb_module; #define PYB_BUILTIN_MODULE_CONSTANTS \ { MP_ROM_QSTR(MP_QSTR_pyb), MP_ROM_PTR(&pyb_module) }, #else #define PYB_BUILTIN_MODULE_CONSTANTS #endif #if MICROPY_PY_STM extern const struct _mp_obj_module_t stm_module; #define STM_BUILTIN_MODULE_CONSTANTS \ { MP_ROM_QSTR(MP_QSTR_stm), MP_ROM_PTR(&stm_module) }, #else #define STM_BUILTIN_MODULE_CONSTANTS #endif #if MICROPY_PY_MACHINE #define MACHINE_BUILTIN_MODULE_CONSTANTS \ { MP_ROM_QSTR(MP_QSTR_machine), MP_ROM_PTR(&mp_module_machine) }, #else #define MACHINE_BUILTIN_MODULE_CONSTANTS #endif #if defined(MICROPY_HW_ETH_MDC) extern const struct _mp_obj_type_t network_lan_type; #define MICROPY_HW_NIC_ETH { MP_ROM_QSTR(MP_QSTR_LAN), MP_ROM_PTR(&network_lan_type) }, #else #define MICROPY_HW_NIC_ETH #endif #if MICROPY_PY_NETWORK_CYW43 extern const struct _mp_obj_type_t mp_network_cyw43_type; #define MICROPY_HW_NIC_CYW43 { MP_ROM_QSTR(MP_QSTR_WLAN), MP_ROM_PTR(&mp_network_cyw43_type) }, #else #define MICROPY_HW_NIC_CYW43 #endif #if MICROPY_PY_NETWORK_WIZNET5K extern const struct _mp_obj_type_t mod_network_nic_type_wiznet5k; #define MICROPY_HW_NIC_WIZNET5K { MP_ROM_QSTR(MP_QSTR_WIZNET5K), MP_ROM_PTR(&mod_network_nic_type_wiznet5k) }, #else #define MICROPY_HW_NIC_WIZNET5K #endif // extra constants #define MICROPY_PORT_CONSTANTS \ MACHINE_BUILTIN_MODULE_CONSTANTS \ PYB_BUILTIN_MODULE_CONSTANTS \ STM_BUILTIN_MODULE_CONSTANTS \ #ifndef MICROPY_BOARD_NETWORK_INTERFACES #define MICROPY_BOARD_NETWORK_INTERFACES #endif #define MICROPY_PORT_NETWORK_INTERFACES \ MICROPY_HW_NIC_ETH \ MICROPY_HW_NIC_CYW43 \ MICROPY_HW_NIC_WIZNET5K \ MICROPY_BOARD_NETWORK_INTERFACES \ #define MP_STATE_PORT MP_STATE_VM // type definitions for the specific machine #define MICROPY_MAKE_POINTER_CALLABLE(p) ((void *)((uint32_t)(p) | 1)) #define MP_SSIZE_MAX (0x7fffffff) // Assume that if we already defined the obj repr then we also defined these items #ifndef MICROPY_OBJ_REPR #define UINT_FMT "%u" #define INT_FMT "%d" typedef int mp_int_t; // must be pointer size typedef unsigned int mp_uint_t; // must be pointer size #endif typedef long mp_off_t; #if MICROPY_PY_THREAD #define MICROPY_EVENT_POLL_HOOK \ do { \ extern void mp_handle_pending(bool); \ mp_handle_pending(true); \ if (pyb_thread_enabled) { \ MP_THREAD_GIL_EXIT(); \ pyb_thread_yield(); \ MP_THREAD_GIL_ENTER(); \ } else { \ __WFI(); \ } \ } while (0); #define MICROPY_THREAD_YIELD() pyb_thread_yield() #else #define MICROPY_EVENT_POLL_HOOK \ do { \ extern void mp_handle_pending(bool); \ mp_handle_pending(true); \ __WFI(); \ } while (0); #define MICROPY_THREAD_YIELD() #endif // Configuration for shared/runtime/softtimer.c. #define MICROPY_SOFT_TIMER_TICKS_MS uwTick #ifndef MICROPY_PY_NETWORK_HOSTNAME_DEFAULT #define MICROPY_PY_NETWORK_HOSTNAME_DEFAULT "mpy-stm32" #endif #if MICROPY_PY_BLUETOOTH_USE_SYNC_EVENTS // Bluetooth code only runs in the scheduler, no locking/mutex required. #define MICROPY_PY_BLUETOOTH_ENTER uint32_t atomic_state = 0; #define MICROPY_PY_BLUETOOTH_EXIT (void)atomic_state; #else // When async events are enabled, need to prevent PendSV execution racing with // scheduler execution. #define MICROPY_PY_BLUETOOTH_ENTER MICROPY_PY_PENDSV_ENTER #define MICROPY_PY_BLUETOOTH_EXIT MICROPY_PY_PENDSV_EXIT #endif #if defined(STM32WB) #define MICROPY_PY_BLUETOOTH_HCI_READ_MODE MICROPY_PY_BLUETOOTH_HCI_READ_MODE_PACKET #else #define MICROPY_PY_BLUETOOTH_HCI_READ_MODE MICROPY_PY_BLUETOOTH_HCI_READ_MODE_BYTE #endif #ifndef MICROPY_PY_BLUETOOTH_ENABLE_CENTRAL_MODE #define MICROPY_PY_BLUETOOTH_ENABLE_CENTRAL_MODE (1) #endif #ifndef MICROPY_PY_BLUETOOTH_ENABLE_L2CAP_CHANNELS #define MICROPY_PY_BLUETOOTH_ENABLE_L2CAP_CHANNELS (MICROPY_BLUETOOTH_NIMBLE) #endif // We need an implementation of the log2 function which is not a macro #define MP_NEED_LOG2 (1) // We need to provide a declaration/definition of alloca() #include <alloca.h> // Needed for MICROPY_PY_RANDOM_SEED_INIT_FUNC. uint32_t rng_get(void);

0 replies

mkphsnbng · 2025-03-28T09:15:41Z

mkphsnbng
Mar 28, 2025
Author

PFA, You can consider this attachment. Regards, From: Dave Festing ***@***.***> Sent: Friday, March 28, 2025 2:24 PM To: micropython/micropython ***@***.***> Cc: Kumar, Manu (FT D IN PAMC MI EMB FW) ***@***.***>; Author ***@***.***> Subject: Re: [micropython/micropython] Micropython for Nucleo-68 WB55 (Discussion #17024) Could you post the mpconfigboard.h that you are building against? - Reply to this email directly, view it on GitHub<#17024 (comment)>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/A6LDIRJ3T3THASE36OMUEYT2WUE3TAVCNFSM6AAAAABZ6PC6AGVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTENRVGA2DKMI>. You are receiving this because you authored the thread.Message ID: ***@***.***> /* * This file is part of the MicroPython project, http://micropython.org/ * * The MIT License (MIT) * * Copyright (c) 2013-2017 Damien P. George * * Permission is hereby granted, free of charge, to any person obtaining a copy * of this software and associated documentation files (the "Software"), to deal * in the Software without restriction, including without limitation the rights * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell * copies of the Software, and to permit persons to whom the Software is * furnished to do so, subject to the following conditions: * * The above copyright notice and this permission notice shall be included in * all copies or substantial portions of the Software. * * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN * THE SOFTWARE. */ // Options to control how MicroPython is built for this port, // overriding defaults in py/mpconfig.h. // board specific definitions #include "mpconfigboard.h" #include "mpconfigboard_common.h" #ifndef MICROPY_CONFIG_ROM_LEVEL #define MICROPY_CONFIG_ROM_LEVEL (MICROPY_CONFIG_ROM_LEVEL_EXTRA_FEATURES) #endif // memory allocation policies #ifndef MICROPY_GC_STACK_ENTRY_TYPE #if MICROPY_HW_SDRAM_SIZE #define MICROPY_GC_STACK_ENTRY_TYPE uint32_t #else #define MICROPY_GC_STACK_ENTRY_TYPE uint16_t #endif #endif #define MICROPY_ALLOC_PATH_MAX (128) // optimisations #ifndef MICROPY_OPT_COMPUTED_GOTO #define MICROPY_OPT_COMPUTED_GOTO (1) #endif // Don't enable lookup cache on M0 (low RAM) #ifndef MICROPY_OPT_MAP_LOOKUP_CACHE #define MICROPY_OPT_MAP_LOOKUP_CACHE (__CORTEX_M > 0) #endif // emitters #define MICROPY_PERSISTENT_CODE_LOAD (1) #ifndef MICROPY_EMIT_THUMB #define MICROPY_EMIT_THUMB (1) #endif #ifndef MICROPY_EMIT_INLINE_THUMB #define MICROPY_EMIT_INLINE_THUMB (1) #endif // Python internal features #define MICROPY_TRACKED_ALLOC (MICROPY_SSL_MBEDTLS || MICROPY_BLUETOOTH_BTSTACK) #define MICROPY_READER_VFS (1) #define MICROPY_ENABLE_GC (1) #define MICROPY_ENABLE_EMERGENCY_EXCEPTION_BUF (1) #define MICROPY_EMERGENCY_EXCEPTION_BUF_SIZE (0) #define MICROPY_REPL_INFO (1) #define MICROPY_LONGINT_IMPL (MICROPY_LONGINT_IMPL_MPZ) #ifndef MICROPY_FLOAT_IMPL // can be configured by each board via mpconfigboard.mk #define MICROPY_FLOAT_IMPL (MICROPY_FLOAT_IMPL_FLOAT) #endif #define MICROPY_USE_INTERNAL_ERRNO (1) #define MICROPY_SCHEDULER_STATIC_NODES (1) #define MICROPY_SCHEDULER_DEPTH (8) #define MICROPY_VFS (1) #ifndef MICROPY_VFS_ROM #define MICROPY_VFS_ROM (MICROPY_HW_ROMFS_ENABLE_INTERNAL_FLASH || MICROPY_HW_ROMFS_ENABLE_EXTERNAL_QSPI) #endif // control over Python builtins #ifndef MICROPY_PY_BUILTINS_HELP_TEXT #define MICROPY_PY_BUILTINS_HELP_TEXT stm32_help_text #endif #ifndef MICROPY_PY_SYS_PLATFORM // let boards override it if they want #define MICROPY_PY_SYS_PLATFORM "pyboard" #endif #ifndef MICROPY_PY_THREAD #define MICROPY_PY_THREAD (0) #endif // extended modules #define MICROPY_PY_HASHLIB_MD5 (MICROPY_PY_SSL) #define MICROPY_PY_HASHLIB_SHA1 (MICROPY_PY_SSL) #define MICROPY_PY_CRYPTOLIB (MICROPY_PY_SSL) #define MICROPY_PY_OS_INCLUDEFILE "ports/stm32/modos.c" #define MICROPY_PY_OS_DUPTERM (3) #define MICROPY_PY_OS_DUPTERM_BUILTIN_STREAM (1) #define MICROPY_PY_OS_DUPTERM_STREAM_DETACHED_ATTACHED (1) #define MICROPY_PY_OS_SYNC (1) #define MICROPY_PY_OS_UNAME (1) #define MICROPY_PY_OS_URANDOM (MICROPY_HW_ENABLE_RNG) #define MICROPY_PY_RANDOM_SEED_INIT_FUNC (rng_get()) #define MICROPY_PY_TIME_GMTIME_LOCALTIME_MKTIME (1) #define MICROPY_PY_TIME_TIME_TIME_NS (1) #define MICROPY_PY_TIME_INCLUDEFILE "ports/stm32/modtime.c" #define MICROPY_PY_LWIP_PPP (MICROPY_PY_NETWORK_PPP_LWIP) #define MICROPY_PY_LWIP_SOCK_RAW (MICROPY_PY_LWIP) #ifndef MICROPY_PY_MACHINE #define MICROPY_PY_MACHINE (1) #define MICROPY_PY_MACHINE_INCLUDEFILE "ports/stm32/modmachine.c" #define MICROPY_PY_MACHINE_RESET (1) #define MICROPY_PY_MACHINE_BARE_METAL_FUNCS (1) #define MICROPY_PY_MACHINE_FREQ_NUM_ARGS_MAX (4) #define MICROPY_PY_MACHINE_BOOTLOADER (1) #define MICROPY_PY_MACHINE_ADC (1) #define MICROPY_PY_MACHINE_ADC_INCLUDEFILE "ports/stm32/machine_adc.c" #ifndef MICROPY_PY_MACHINE_BITSTREAM #define MICROPY_PY_MACHINE_BITSTREAM (1) #endif #define MICROPY_PY_MACHINE_DHT_READINTO (1) #define MICROPY_PY_MACHINE_PULSE (1) #define MICROPY_PY_MACHINE_PIN_MAKE_NEW mp_pin_make_new #define MICROPY_PY_MACHINE_I2C (MICROPY_HW_ENABLE_HW_I2C) #define MICROPY_PY_MACHINE_SOFTI2C (1) #define MICROPY_PY_MACHINE_I2S_INCLUDEFILE "ports/stm32/machine_i2s.c" #define MICROPY_PY_MACHINE_I2S_CONSTANT_RX (I2S_MODE_MASTER_RX) #define MICROPY_PY_MACHINE_I2S_CONSTANT_TX (I2S_MODE_MASTER_TX) #define MICROPY_PY_MACHINE_I2S_RING_BUF (1) #define MICROPY_PY_MACHINE_SPI (1) #define MICROPY_PY_MACHINE_SPI_MSB (SPI_FIRSTBIT_MSB) #define MICROPY_PY_MACHINE_SPI_LSB (SPI_FIRSTBIT_LSB) #define MICROPY_PY_MACHINE_SOFTSPI (1) #define MICROPY_PY_MACHINE_TIMER (1) #define MICROPY_PY_MACHINE_UART (1) #define MICROPY_PY_MACHINE_UART_INCLUDEFILE "ports/stm32/machine_uart.c" #define MICROPY_PY_MACHINE_UART_IRQ (1) #define MICROPY_PY_MACHINE_UART_READCHAR_WRITECHAR (1) #define MICROPY_PY_MACHINE_UART_SENDBREAK (1) #define MICROPY_PY_MACHINE_WDT (1) #define MICROPY_PY_MACHINE_WDT_INCLUDEFILE "ports/stm32/machine_wdt.c" #endif #define MICROPY_HW_SOFTSPI_MIN_DELAY (0) #define MICROPY_HW_SOFTSPI_MAX_BAUDRATE (HAL_RCC_GetSysClockFreq() / 48) #define MICROPY_PY_WEBSOCKET (MICROPY_PY_LWIP) #define MICROPY_PY_WEBREPL (MICROPY_PY_LWIP) #ifndef MICROPY_PY_NETWORK #define MICROPY_PY_NETWORK (1) #endif #ifndef MICROPY_PY_ONEWIRE #define MICROPY_PY_ONEWIRE (1) #endif // optional network features #if MICROPY_PY_NETWORK #ifndef MICROPY_PY_SOCKET #define MICROPY_PY_SOCKET (1) #endif #ifndef MICROPY_PY_NETWORK_PPP_LWIP #define MICROPY_PY_NETWORK_PPP_LWIP (0) #endif #endif // fatfs configuration used in ffconf.h #define MICROPY_FATFS_ENABLE_LFN (2) #define MICROPY_FATFS_LFN_CODE_PAGE 437 /* 1=SFN/ANSI 437=LFN/U.S.(OEM) */ #define MICROPY_FATFS_USE_LABEL (1) #define MICROPY_FATFS_RPATH (2) #define MICROPY_FATFS_MULTI_PARTITION (1) #if MICROPY_PY_PYB extern const struct _mp_obj_module_t pyb_module; #define PYB_BUILTIN_MODULE_CONSTANTS \ { MP_ROM_QSTR(MP_QSTR_pyb), MP_ROM_PTR(&pyb_module) }, #else #define PYB_BUILTIN_MODULE_CONSTANTS #endif #if MICROPY_PY_STM extern const struct _mp_obj_module_t stm_module; #define STM_BUILTIN_MODULE_CONSTANTS \ { MP_ROM_QSTR(MP_QSTR_stm), MP_ROM_PTR(&stm_module) }, #else #define STM_BUILTIN_MODULE_CONSTANTS #endif #if MICROPY_PY_MACHINE #define MACHINE_BUILTIN_MODULE_CONSTANTS \ { MP_ROM_QSTR(MP_QSTR_machine), MP_ROM_PTR(&mp_module_machine) }, #else #define MACHINE_BUILTIN_MODULE_CONSTANTS #endif #if defined(MICROPY_HW_ETH_MDC) extern const struct _mp_obj_type_t network_lan_type; #define MICROPY_HW_NIC_ETH { MP_ROM_QSTR(MP_QSTR_LAN), MP_ROM_PTR(&network_lan_type) }, #else #define MICROPY_HW_NIC_ETH #endif #if MICROPY_PY_NETWORK_CYW43 extern const struct _mp_obj_type_t mp_network_cyw43_type; #define MICROPY_HW_NIC_CYW43 { MP_ROM_QSTR(MP_QSTR_WLAN), MP_ROM_PTR(&mp_network_cyw43_type) }, #else #define MICROPY_HW_NIC_CYW43 #endif #if MICROPY_PY_NETWORK_WIZNET5K extern const struct _mp_obj_type_t mod_network_nic_type_wiznet5k; #define MICROPY_HW_NIC_WIZNET5K { MP_ROM_QSTR(MP_QSTR_WIZNET5K), MP_ROM_PTR(&mod_network_nic_type_wiznet5k) }, #else #define MICROPY_HW_NIC_WIZNET5K #endif // extra constants #define MICROPY_PORT_CONSTANTS \ MACHINE_BUILTIN_MODULE_CONSTANTS \ PYB_BUILTIN_MODULE_CONSTANTS \ STM_BUILTIN_MODULE_CONSTANTS \ #ifndef MICROPY_BOARD_NETWORK_INTERFACES #define MICROPY_BOARD_NETWORK_INTERFACES #endif #define MICROPY_PORT_NETWORK_INTERFACES \ MICROPY_HW_NIC_ETH \ MICROPY_HW_NIC_CYW43 \ MICROPY_HW_NIC_WIZNET5K \ MICROPY_BOARD_NETWORK_INTERFACES \ #define MP_STATE_PORT MP_STATE_VM // type definitions for the specific machine #define MICROPY_MAKE_POINTER_CALLABLE(p) ((void *)((uint32_t)(p) | 1)) #define MP_SSIZE_MAX (0x7fffffff) // Assume that if we already defined the obj repr then we also defined these items #ifndef MICROPY_OBJ_REPR #define UINT_FMT "%u" #define INT_FMT "%d" typedef int mp_int_t; // must be pointer size typedef unsigned int mp_uint_t; // must be pointer size #endif typedef long mp_off_t; #if MICROPY_PY_THREAD #define MICROPY_EVENT_POLL_HOOK \ do { \ extern void mp_handle_pending(bool); \ mp_handle_pending(true); \ if (pyb_thread_enabled) { \ MP_THREAD_GIL_EXIT(); \ pyb_thread_yield(); \ MP_THREAD_GIL_ENTER(); \ } else { \ __WFI(); \ } \ } while (0); #define MICROPY_THREAD_YIELD() pyb_thread_yield() #else #define MICROPY_EVENT_POLL_HOOK \ do { \ extern void mp_handle_pending(bool); \ mp_handle_pending(true); \ __WFI(); \ } while (0); #define MICROPY_THREAD_YIELD() #endif // Configuration for shared/runtime/softtimer.c. #define MICROPY_SOFT_TIMER_TICKS_MS uwTick #ifndef MICROPY_PY_NETWORK_HOSTNAME_DEFAULT #define MICROPY_PY_NETWORK_HOSTNAME_DEFAULT "mpy-stm32" #endif #if MICROPY_PY_BLUETOOTH_USE_SYNC_EVENTS // Bluetooth code only runs in the scheduler, no locking/mutex required. #define MICROPY_PY_BLUETOOTH_ENTER uint32_t atomic_state = 0; #define MICROPY_PY_BLUETOOTH_EXIT (void)atomic_state; #else // When async events are enabled, need to prevent PendSV execution racing with // scheduler execution. #define MICROPY_PY_BLUETOOTH_ENTER MICROPY_PY_PENDSV_ENTER #define MICROPY_PY_BLUETOOTH_EXIT MICROPY_PY_PENDSV_EXIT #endif #if defined(STM32WB) #define MICROPY_PY_BLUETOOTH_HCI_READ_MODE MICROPY_PY_BLUETOOTH_HCI_READ_MODE_PACKET #else #define MICROPY_PY_BLUETOOTH_HCI_READ_MODE MICROPY_PY_BLUETOOTH_HCI_READ_MODE_BYTE #endif #ifndef MICROPY_PY_BLUETOOTH_ENABLE_CENTRAL_MODE #define MICROPY_PY_BLUETOOTH_ENABLE_CENTRAL_MODE (1) #endif #ifndef MICROPY_PY_BLUETOOTH_ENABLE_L2CAP_CHANNELS #define MICROPY_PY_BLUETOOTH_ENABLE_L2CAP_CHANNELS (MICROPY_BLUETOOTH_NIMBLE) #endif // We need an implementation of the log2 function which is not a macro #define MP_NEED_LOG2 (1) // We need to provide a declaration/definition of alloca() #include <alloca.h> // Needed for MICROPY_PY_RANDOM_SEED_INIT_FUNC. uint32_t rng_get(void);

5 replies

davefes Mar 28, 2025

I deleted my post after looking up the mpconfigboard.h:

// UART buses
#define MICROPY_HW_UART1_TX         (pin_B6)
#define MICROPY_HW_UART1_RX         (pin_B7)
#define MICROPY_HW_LPUART1_TX       (pin_A2)
#define MICROPY_HW_LPUART1_RX       (pin_A3)
// USART 1 is connected to the virtual com port on the ST-LINK
#define MICROPY_HW_UART_REPL        PYB_UART_1
#define MICROPY_HW_UART_REPL_BAUD   115200

and saw ST-LINK was supposed to be connected to UART1. I would try a FTDI programmer on pins B6 and B7 to see if the REPL appears there. I have never tried to use the ST-LINK to load .py files or to observe what is happening on the device.

An expert is required!

davefes Mar 28, 2025

Have you tried the image at:
https://micropython.org/download/NUCLEO_WB55/

mkphsnbng Apr 1, 2025
Author

I have done changes as mentioned above in mpconfigboard.h(micropython/ports/stm32/mpconfigport.h)
// UART buses
#define MICROPY_HW_UART1_TX (pin_B6)
#define MICROPY_HW_UART1_RX (pin_B7)
#define MICROPY_HW_LPUART1_TX (pin_A2)
#define MICROPY_HW_LPUART1_RX (pin_A3)
// USART 1 is connected to the virtual com port on the ST-LINK
#define MICROPY_HW_UART_REPL PYB_UART_1
#define MICROPY_HW_UART_REPL_BAUD 115200

after that we got firmware.bin and flashed with 0x08000000 even in that i am not getting REPL and no python console when we open COM port

any other inputs ?

davefes Apr 1, 2025

I use Linux. Does the dev board say that it is connected to a specific COM port? In Ubuntu cd /dev and then ls. On Windows can you check in Device Manager?

mkphsnbng Apr 3, 2025
Author

with the above changes its not working.. parallely we have change UART1_TX (pin_B6) and UART1_RX (pin_B7) in STM32 cube IDE and able to run and we are able to see standard message which there was a standard logs.. when i see wb55 board rev no: MB1355C (which is mentioned on board)

mkphsnbng · 2025-03-28T10:40:34Z

mkphsnbng
Mar 28, 2025
Author

Can you please provide the link to flash firmware.bin and firmware.hex or elf files.. As I am not able to enter to dfu mode.. Please provide link or image firmware.bin ***@***.*** Thanks Regards, Manu From: Dave Festing ***@***.***> Sent: Friday, March 28, 2025 3:22 PM To: micropython/micropython ***@***.***> Cc: Kumar, Manu (FT D IN PAMC MI EMB FW) ***@***.***>; Author ***@***.***> Subject: Re: [micropython/micropython] Micropython for Nucleo-68 WB55 (Discussion #17024) Have you tried the image at: https://micropython.org/download/NUCLEO_WB55/ - Reply to this email directly, view it on GitHub<#17024 (reply in thread)>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/A6LDIRLTMAWDXYAEW6AA24L2WULVPAVCNFSM6AAAAABZ6PC6AGVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTENRVGEYTANQ>. You are receiving this because you authored the thread.Message ID: ***@***.***>

0 replies

mkphsnbng · 2025-03-28T13:04:38Z

mkphsnbng
Mar 28, 2025
Author

Sorry my bad.. I am able to download hex file.. from the link you provided.. I tried to flash firmware.hex file into 0x08000000. Currently I used below configuration ***@***.*** I am able to get the log from the COM(which observed device manager) port after configuring USART1 for the port PB6 and PB7 as per the datasheet and user manual. Also I configured the switch SW1 and SW1(here please let me know if I missed anything) When I flashed hex file(latest) to 0x08000000 as mention in below link And I did hold reset button for 5 seccond within that time I did BOOT 0(SW2) I hold for 4-5 seccond and left reset button 1st an slare SW2.. Even after that I am facing same issue.. Is there anything else I need to do to achieve this? Regards, Manu From: Kumar, Manu (FT D IN PAMC MI EMB FW) Sent: Friday, March 28, 2025 4:10 PM To: micropython/micropython ***@***.***>; micropython/micropython ***@***.***> Cc: Author ***@***.***> Subject: RE: [micropython/micropython] Micropython for Nucleo-68 WB55 (Discussion #17024) Can you please provide the link to flash firmware.bin and firmware.hex or elf files.. As I am not able to enter to dfu mode.. Please provide link or image firmware.bin ***@***.*** Thanks Regards, Manu From: Dave Festing ***@***.******@***.***>> Sent: Friday, March 28, 2025 3:22 PM To: micropython/micropython ***@***.******@***.***>> Cc: Kumar, Manu (FT D IN PAMC MI EMB FW) ***@***.******@***.***>>; Author ***@***.******@***.***>> Subject: Re: [micropython/micropython] Micropython for Nucleo-68 WB55 (Discussion #17024) Have you tried the image at: https://micropython.org/download/NUCLEO_WB55/ - Reply to this email directly, view it on GitHub<#17024 (reply in thread)>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/A6LDIRLTMAWDXYAEW6AA24L2WULVPAVCNFSM6AAAAABZ6PC6AGVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTENRVGEYTANQ>. You are receiving this because you authored the thread.Message ID: ***@***.******@***.***>>

1 reply

davefes Mar 28, 2025

All of my experience is using the STM32F411 BlackPill dev board.. I use STM32Cube programmer and load the provided .hex images. You need an expert on the WB55 units.

Also, your reply messages are "different". They have a lot of quoted information,

mkphsnbng · 2025-04-01T04:22:04Z

mkphsnbng
Apr 1, 2025
Author

Yes, Request to please provide information or images how to resolve this issue.. as with default image also we are not able to see micropython console. Let me know if there is any additional settings I need to do.. Regards Manu From: Dave Festing ***@***.***> Sent: Saturday, March 29, 2025 1:05 AM To: micropython/micropython ***@***.***> Cc: Kumar, Manu (FT D IN PAMC MI EMB FW) ***@***.***>; Author ***@***.***> Subject: Re: [micropython/micropython] Micropython for Nucleo-68 WB55 (Discussion #17024) All of my experience is using the STM32F411 BlackPill dev board.. I use STM32Cube programmer and load the provided .hex images. You need an expert on the WB55 units. Also, your reply messages are "different". They have a lot of quoted information, - Reply to this email directly, view it on GitHub<#17024 (reply in thread)>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/A6LDIRN7X4RQIE3C3WC3G332WWP7RAVCNFSM6AAAAABZ6PC6AGVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTENRVG43DKMA>. You are receiving this because you authored the thread.Message ID: ***@***.***>

0 replies

andrewleech · 2025-04-01T04:36:09Z

andrewleech
Apr 1, 2025
Collaborator Sponsor

Did you see the suggestion in https://github.com/orgs/micropython/discussions/17024#discussioncomment-12651106
The firmware from https://micropython.org/download/NUCLEO_WB55/ should most likely be correct for your board

8 replies

andrewleech Apr 1, 2025
Collaborator Sponsor

Are you using cube programmer to program the hex file? Does it verify that it's written?

There might be some other fuses set wrong that are changing the boot mode. You might need to find what the default settings are for all of them and check, there's quite a few in different tabs on cube programmer.

After programming it, can you plug a second USB cable into the other port as well, does it come up as a USB com port?

mkphsnbng Apr 1, 2025
Author

Are you using cube programmer to program the hex file? Does it verify that it's written?
Yes using cube programmer to program the hex file. Yes it verifed
There might be some other fuses set wrong that are changing the boot mode. You might need to find what the default settings are for all of them and check, there's quite a few in different tabs on cube programmer.
AS per the MicroPython - Python for microcontrollers the jumper setting are same..
After programming it, can you plug a second USB cable into the other port as well, does it come up as a USB com port?
Yes, but there is no luck..

mkphsnbng Apr 2, 2025
Author

Also, there is 1 observation we made that once after flashing micropython i opened the drive in file explorer.. i am able to see only 2 files.
embed.htm and default.txt

andrewleech Apr 2, 2025
Collaborator Sponsor

does it come up as a USB com port?\nYes, but there is no luck..

So the second USB port is recognised as an additional com port? If so that means the firmware is running!

The mass storage / flash drive that has those files, is that on the stlink USB port? If so then that's normal and expected I think.

Back to the second USB port, if that's coming up as a com port, try connecting with mpremote to that particular port, eg mpremote connect COM6 resume
It'll say it's connected to the port and ^] to exit.

Assuming it doesn't have the repl visible after that, try hitting ctrl-c or ctrl-d and see if anything happens.

You could also try a mass erase of the chip in cube programmer then program the hex again and see if that changes anything.

mkphsnbng Apr 2, 2025
Author

So the second USB port( is recognised as an additional com port? If so that means the firmware is running!
-> there are 2 USB port 1 port flashing via USB-STLink micro usb port (COM5 port ) and USB user port is not observing in device manager
Back to the second USB port, if that's coming up as a com port, try connecting with mpremote to that particular port, eg mpremote connect COM6 resume
-> seccond usb port not coming up
Assuming it doesn't have the repl visible after that, try hitting ctrl-c or ctrl-d and see if anything happens.
-> Did but no luck
You could also try a mass erase of the chip in cube programmer then program the hex again and see if that changes anything.
-> Did but no luck

mkphsnbng · 2025-04-01T09:04:40Z

mkphsnbng
Apr 1, 2025
Author

In ubuntu I am getting as below, i.e, it detected as /dev/ttyACM0 ***@***.*** In Windows its detecting as COM5(stmicroelecronics STLink Virtual COM port (COM5) ***@***.*** Is this correct? Regards, Manu From: Dave Festing ***@***.***> Sent: Tuesday, April 1, 2025 2:02 PM To: micropython/micropython ***@***.***> Cc: Kumar, Manu (FT D IN PAMC MI EMB FW) ***@***.***>; Author ***@***.***> Subject: Re: [micropython/micropython] Micropython for Nucleo-68 WB55 (Discussion #17024) I use Linux. Does the dev board say that it is connected to a specific COM port? In Ubuntu cd /dev and then ls. On Windows can you check in Device Manager? - Reply to this email directly, view it on GitHub<#17024 (reply in thread)>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/A6LDIRK472PYVLHNVQMAFRD2XJMKVAVCNFSM6AAAAABZ6PC6AGVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTENRYGU3TCMI>. You are receiving this because you authored the thread.Message ID: ***@***.***>

0 replies

mkphsnbng · 2025-04-02T03:53:11Z

mkphsnbng
Apr 2, 2025
Author

[Heads Up]

Also, 1 more update.. we have tried to flash(default image) https://micropython.org/download/USBDONGLE_WB55/ as we have this USB Dongle.. controller too.. in this controller also i am facing same..
after flashing i am not able to see any device entry in device manager.. i felt this is weird.. i tried with changing switch settings which is available in controller..
both led D2 and D3 are in brick led status( neither they both are ON of OFF)

1 reply

davefes Apr 2, 2025

I am surprised that on Ubuntu it shows up as /dev/ttyACM0. When you unplug the device /dev/ttyACM0 disappears?
Have you been able to run Micropython on any device?

If not, I would suggest a device that has a lot more forum support, ie ESP32 or more common STM32 platforms.

mkphsnbng · 2025-04-03T12:56:00Z

mkphsnbng
Apr 3, 2025
Author

Thanks All, a lot for the suggestions..

I found root cause for this.. it’s the controller board issue.. i used other controller and I am able to get the micropython running..
I was just going through the example and running micropython with the link https://stm32python.gitlab.io/en/docs/Micropython/[Downloads](https://stm32python.gitlab.io/en/docs/Micropython/Downloads#firmwares)#firmwares

Here I am not able to download the firmware.. can you please provide other links if we have any? Or please share this as in this Start with MicroPython and the NUCLEO-WB55 they have mentioned to download firmware.

I thank again for inputs provided

1 reply

andrewleech Apr 4, 2025
Collaborator Sponsor

Good to hear you have a path forward with another board. Yes these wb55's can be bricked in a number of ways unfortunately.

If you want to try to recover the broken controller, try looking at a working one connected in cube programmer. Go to the tabs on the left side for option bytes and similar settings and take screenshots of everything, scrolling down to capture all settings.

Then compare these on the broken one.

There's a few settings in these lists that can block startup.

Also look up guides for upgrading the wireless bootloader and firmware, sometimes these need to be reflashed.

For micropython use you want the hci only firmware pack, not the full stack.

MicroPython

Micropython for Nucleo-68 WB55 #17024

Uh oh!

mkphsnbng Mar 28, 2025

Replies: 9 comments · 16 replies

Uh oh!

mkphsnbng Mar 28, 2025 Author

Uh oh!

mkphsnbng Mar 28, 2025 Author

Uh oh!

davefes Mar 28, 2025

Uh oh!

davefes Mar 28, 2025

Uh oh!

mkphsnbng Apr 1, 2025 Author

Uh oh!

davefes Apr 1, 2025

Uh oh!

Uh oh!

mkphsnbng Apr 3, 2025 Author

Uh oh!

mkphsnbng Mar 28, 2025 Author

Uh oh!

mkphsnbng Mar 28, 2025 Author

Uh oh!

davefes Mar 28, 2025

Uh oh!

mkphsnbng Apr 1, 2025 Author

Uh oh!

andrewleech Apr 1, 2025 Collaborator Sponsor

Uh oh!

andrewleech Apr 1, 2025 Collaborator Sponsor

Uh oh!

mkphsnbng Apr 1, 2025 Author

Uh oh!

mkphsnbng Apr 2, 2025 Author

Uh oh!

andrewleech Apr 2, 2025 Collaborator Sponsor

Uh oh!

mkphsnbng Apr 2, 2025 Author

Uh oh!

mkphsnbng Apr 1, 2025 Author

Uh oh!

Uh oh!

mkphsnbng Apr 2, 2025 Author

Uh oh!

Uh oh!

davefes Apr 2, 2025

Uh oh!

mkphsnbng Apr 3, 2025 Author

Uh oh!

andrewleech Apr 4, 2025 Collaborator Sponsor

mkphsnbng
Mar 28, 2025

Replies: 9 comments 16 replies

mkphsnbng
Mar 28, 2025
Author

mkphsnbng
Mar 28, 2025
Author

mkphsnbng Apr 1, 2025
Author

mkphsnbng Apr 3, 2025
Author

mkphsnbng
Mar 28, 2025
Author

mkphsnbng
Mar 28, 2025
Author

mkphsnbng
Apr 1, 2025
Author

andrewleech
Apr 1, 2025
Collaborator Sponsor

andrewleech Apr 1, 2025
Collaborator Sponsor

mkphsnbng Apr 1, 2025
Author

mkphsnbng Apr 2, 2025
Author

andrewleech Apr 2, 2025
Collaborator Sponsor

mkphsnbng Apr 2, 2025
Author

mkphsnbng
Apr 1, 2025
Author

mkphsnbng
Apr 2, 2025
Author

mkphsnbng
Apr 3, 2025
Author

andrewleech Apr 4, 2025
Collaborator Sponsor